Accu-Chek GO Quick Reference Guide

Beep tone
Press and hold down
(for more than 3 seconds)
Time &
Date
Time-and-
date format
Hours
Minutes
Time
Date
Year
Month
Day
Press briefly
(turn off
)
On
(On1)
Off
(OFF)
Acoustic Mode
(On2)
Press briefly
(turn off
)
Target range
Off
On
Value
Lower limit
(LL)
Off
On
Value
Upper limit
(LH)
Press briefly
(turn off
)
Alarm clock function
Press briefly
(turn off
)
Press briefly
(turn off
)
Turning on the meter
and starting Quick
set-up
Off
On
Hours
Minutes
AL1
AL2
AL3
AL4













Top and sides
 Þ button: turn on or off, start a set-up to
change settings, save entries
 Liquid crystal display (LCD)
 < and > buttons: change settings (decre-
ment and increment value, respectively),
retrieve results, request averages
 Test strip guide – this is where you insert the
test strip
 Measurement optics cover
 Test strip ejector
 Code chip
 Infrared port for downloading results to a PC,
for instance
Bottom
 Code chip
 Code chip slot
 Type plate
 Battery compartment
 Battery (type CR 2032)
1 Set-up
2 When an average is displayed: number of days
covered
3 LH or LL: target range setting (set-up)
4 Alarm clock function turned on.
Flashing: optical signal during alarm
5 Test or averaging in progress
6 Unit of measurement for BG result
7 Flag indicating special result
8 Flashing: cue to allow test strip to draw up
blood
9 Flashing: cue to insert test strip
10 Test strips are past their expiry date
11 Code number display.
Flashing: code chip is missing
12 Target range setting (set-up).
Flashing: result is outside the target range
13 Flag indicating quality control
14 Flashing: temperature is/was outside the
permitted range
15 Beep tone or Acoustic Mode is turned on
16 Flashing: battery is running low
17 When an average is displayed: number of
results included
18 Memory, averages or results download
19 Follows time in 12-hour format
20 Display messages
Code chip is missing.
In memory: no results in memory, averaging
not possible or result erased
Alarm setting (set-up)
Flashing: latest result being erased
End of set-up, self-test following test or
download complete
In Quick set-up: group selected
Result >600 mg/dL (33.3 mmol/L)
Result <10 mg/dL (0.6 mmol/L)
Results download
Error messages
E-1
Test strip inserted incorrectly, test strip
bent/moved, strong electromagnetic
field
E-2
Code chip from another system, meter
cannot read code chip, code chip defec
-
tive, code chip removed during test
E-4
Measurement optics dirty, test strip
drew up blood too soon, test strip bent/
moved, used strip inserted, test strip
past its expiry date, new test strip inser
-
ted too soon after last test (while End
was showing)
E-6
Test strip drew up too little blood, test
strip drew up blood too soon, test strip
bent/moved, battery empty, meter error,
strong electromagnetic field
EEE
Meter error
ttt
Temperature too low or too high to test.
Quick set-up: Changing settings
Þ press and held down for more than 3 seconds at
anytime = save, exit set-up and turn off
< > change with < or >
press briefly = save or scroll
17
18
16
15
14
13
7
6
5
4
20
3
2
1
11 10 9 8
19
12

Accu-Chek GO Specifications

General

Brand	Accu-Chek
Model	GO
Category	Blood Glucose Meter
Language	English