Agilent Technologies HP 83712A Calibration Guide

l-28. Typical Puke Modulation Envelope IIIustrates the Past Rise and PaII Times,
Excellent Flatness and Puke Fidelity
..................
l-29. Typical Log AM Error (deviation from desired depth) at 25 OC for Carrier
Frequencies between 1.0 and 20 GHz
..................
3-l. Internal Timebase Aging Rate Test Equipment Setup
.............
3-2. kequency Range and Resolution Test Setup
.................
3-3. External Leveling Test Setup
........................
3-4. Maximum Power Test Setup
........................
3-5. Vernier Level Accuracy and Flatness Test Setup
...............
3-6. Low Level Accuracy Test Setup using Power Meter
..............
3-7. 10 MHz to 1 GHz Low Level Accuracy Test Setup using Measuring Receiver
. .
3-8. 1 GHz to 18 GHz Low Level Accuracy Test Setup using Measuring Receiver
. .
3-9. Harmonics Test Setup
...........................
3-10. Siie-Sideband Phase Noise Test Setup
...................
3-11. Non-Harmonic Spurious Level ~30 kHz Test Setup
..............
3-12. Non-Harmonic Spurious Level >30 kHz Test Setup
..............
3-13. Puke On/Off Ratio Test Setup
........................
3-14. PuIseRise/FkUTimeTestSetup
.......................
3-15. P&e Rise Time Measurement
.......................
3-16. Puke PaII Time Measurement
........................
3-17.PuIseWidth’IkstSetup
...........................
3-18. Pulse Width Measurement
.........................
3-19. Maximum FM Deviation Test Setup
.....................
3-20. Example Signal Spectrum that Passes l&t
..................
3-21. Example SiiaI Spectrum that Fails Test
...................
3-22. FM Rate and Flatness lkst Setup
......................
3-23. 4M Flatness Test Setup
...........................
3-24. Minimum AM Depth Test Setup
.......................
3-25. Minim~LinearAMDepthTestSetup
...................
3-26. Internal AM Rate ‘I&t Setup
........................
3-27. Internal FM Source Verification Test Setup
..................
3-28. Example Signal Spectrum that Passes ‘I&t
..................
3-29. Example Signal Spectrum that Fails l&t
...................
6-l. DIP Switch, A3S1, Settings
.........................
6-2. High stability Timebase Adjustment Equipment Setup
............
6-3. Low Stabihty Timebase Equipment Setup
..................
64. 0.5 V/GHz Output Equipment Setup
.....................
6-5. PM Sensitivity Equipment Setup
......................
6-6. 4M Sensitivity Equipment Setup
......................
6-7. Phase Cross-Over Equipment Setup
.....................
6-8. Linear AM Offset Equipment Setup
.....................
7-l. DIP Switch, A3S1, Settings
.........................
7-2. l-20 GHz Vernier Calibration Equipment Setup
...............
7-3. l-20 GHz Frequency Calibration Equipment Setup
.............
7-4. l-20 GHz Frequency Calibration 2 Equipment Setup
............
7-5. l-20 GHz Attenuator Calibration Equipment Setup
.............
7-6. l-20 GHz AM Linearity Calibration Equipment Setup
............
7-7. l-20 GHz Log AM Gain Calibration Equipment Setup
............
7-8. l-20 GHz Linear AM Calibration Equipment Setup
.............
7-9. 0.01-l GHz Vernier Calibration Equipment Setup
..............
7-10. 0.01-l GHz Frequency Calibration 1 Equipment Setup
............
7-11. 0.01-l GHz Frequency Calibration 2 Equipment Setup
............
7-12. 0.01-l GHz Attenuator Calibration Equipment Setup
............
7-13. 0.01-l GHz AM Calibration Equipment Setup
................
7-14. 0.01-l GHz Linear AM Calibration Equipment Setup
............
l-27
l-30
3-4
3-6
3-8
3-11
3-15
3-18
3-20
3-23
3-29
3-33
3-39
3-44
3-47
3-49
3-50
3-51
3-52
3-53
3-55
3-56
3-57
3-59
3-64
3-68
3-70
3-72
3-74
3-75
3-76
6-3
6-6
6-7
6-8
6-9
6-11
6-13
6-15
7-3
7-7
7-9
7-10
7-12
7-14
7-16
7-19
7-21
7-23
7-24
7-25
7-27
7-29
Contents-~

Agilent Technologies HP 83712A Specifications

General

Brand	Agilent Technologies
Model	HP 83712A
Category	Test Equipment
Language	English