on = Option Enabled (factory default setting)
oFF = Option Disabled
5. Press the DELICATES (∧) or the COLD (∨) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Programmable Push Start Display PPSt
This option allows the owner to enable or disable allowing the
control to display the corresponding command to press the
START (enter) keypad once the vend has been satisfied.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until PPSt appears in the
display.
4.
When PPSt appears in the display, press the START (enter)
keypad. The current Push Start status will appear in the dis-
play.
on = Option Enabled (factory default setting)
oFF = Option Disabled
5. Press the DELICATES (∧) or the COLD (∨) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Programmable Open Lid Display PodL
This option allows the owner to enable or disable allowing the
control to display the corresponding command to open the lid
along with the cycle time when the cycle had completed.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until PodL appears in the
display.
4.
When PodL appears in the display, press the START (enter)
keypad. The current status will appear in the display.
on = Option Enabled (factory default setting)
oFF = Option Disabled
5. Press the DELICATES (∧) or the COLD (∨) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Vend Price Display Override AtS do
This option allows the owner to override the previously set vend
price with a custom display that is set by the payment system.
The default display is CArd if the payment system does not mod-
ify it.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until “ AtS do ” appears in
the display.
4.
When AtS do appears in the display, press the START (en-
ter) keypad. The current Vend Price Display Override status
will appear in the display.
on = Option Enabled
oFF = Option Disabled (factory default setting)
5. Press the DELICATES (∧) or the COLD (∨) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
OPL Parameters oPL-
This option allows the owner to enable or disable the OPL Pa-
rameters in which no vend price needs to be satisfied to operate
the machine.
1. Control must be in Manual Mode. Refer to How to Enter the
Manual Mode.
2. Press the DELICATES (∧) or the COLD (∨) keypad until
Prog appears in the display. Press the START (enter) keypad,
and AtS 1 will appear in the display.
3. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the programmable options until oPL- appears in the
display.
4.
When oPL- appears in the display, press the START (enter)
keypad to enter the OPL submenu.
5. Press the DELICATES (∧) or the COLD (∨) keypad to scroll
through the OPL submenu options.
6. Press the START (enter) keypad when the desired option ap-
pears in the display
OPL Mode Enable oPL 1
This option allows the owner to place the control in OPL Mode,
in which no vend price needs to be satisfied in order to start the
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
65 Part No. 204370ENR1
To Next Page
Loading...
Need help?
General