Quick Start Guide
3400 MAX PSI* Pressure Washer
Unpack pressure washer
Remove everything from carton except pressure washer.1.
Open carton completely by cutting each corner from top to bottom. 2.
Ensure you have all included items prior to assembly. If items are 3.
damaged or missing, call 1-800-743-4115.
Assemble pressure washer
Place handle (a) onto handle supports connected to main unit. Make 1.
sure holes in handle align with holes on handle supports.
1
NOTE: It may be necessary to move the handle supports from side to
side in order to align the handle so it will slide over the handle supports.
Insert carriage bolts (k) through holes from front of unit and attach 2.
plastic knobs (j) from back of unit. Tighten by hand.
2
Place accessory tray (h) over holes on handle (a) (viewing from front 3.
of unit). Push the tree clips (f) into the holes until they sit flat against
the accessory tray.
3
Insert spray gun holder (n) wireform through hole on left side of 4.
handle (viewing from front of unit). Hold wireform in place and
attach a plastic knob (j) from inside of unit. Tighten by hand.
4
Place hose reel onto left side of handle (a) (viewing from back of 5.
unit) just above carriage bolt. Make sure pin (A) in hose reel clamp
inserts in hole (B) on handle.
5
NOTE: Make sure hose reel is attached to the handle facing the engine.
Close hose reel clamp (C) and insert “T” bolt (e1). Tighten by hand.6.
6
Remove shipping cap (D) from fitting on hose reel and attach one 7.
end of the shorter high pressure hose (m) to reel fitting (E). Tighten
by hand.
7
Attach other end of shorter high pressure hose (m) to high pressure 8.
outlet (F) on pump. Tighten by hand.
8
Uncoil high pressure hose (p) and slide metal reinforced end through 9.
hole of hose reel (b).
9
Attach high pressure hose (p) to fitting on hose reel (b). Tighten by 10.
hand.
10
Slide hose clamp (e2) onto high pressure hose. Using an 8 mm 11.
wrench and a phillips screwdriver, attach hose clamp to hose reel
with screw (e4) and lock nut (e3).
11
Pull ring on pin (G) and rotate to vertical position to lock pin open.12.
12
Pull hose reel handle outward and coil high pressure hose onto hose 13.
reel.
Line up pin with hole in hose reel and pull ring on pin. Rotate to 14.
horizontal position and let ring slide into groove to lock hose reel in
place.
Copyright © 2009. All rights reserved. No part of this material may be reproduced or transmitted in any form without the express written permission of Briggs & Stratton Power Products Group, LLC.
Every effort has been made to ensure that the information in this document is accurate and correct. However, we reserve the right to alter or otherwise improve the product and this document at any time without prior notice and without incurring obligation.
*This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard PW101 (Testing and Rating Performance of Pressure Washers).
Add engine oil and fuel
NOTICE You MUST properly fill engine with oil before attempting to start
pressure washer.
NOTICE DO NOT use E85 fuel.
NOTICE DO NOT mix oil with fuel.
Move pressure washer outdoors to a flat, level surface.1.
Remove oil fill cap (H). Slowly pour supplied oil (g) into oil fill, 2.
frequently checking oil level. Do not over fill. Replace and fully tighten
oil fill cap.
13
Remove fuel cap (J). Add clean, fresh, UNLEADED fuel. Allow space 3.
in fuel tank for fuel expansion.
13
Replace fuel cap. Let any spilled fuel evaporate before starting 4.
engine.
Move pressure washer
to safe operating location
Move pressure washer outdoors to a flat, level surface. Running 1.
engines give off carbon monoxide.
14
Keep at least 5 ft. (1.5m) clearance on all sides of pressure washer 2.
including overhead to reduce the risk of exhaust heat or exhaust
gases igniting nearby combustible material.
Connect spray gun
Attach rubber reinforced end of high pressure hose (p) to base of 1.
spray gun (s). Tighten by hand.
15
Connect water supply
Remove and discard shipping cap from garden hose inlet 1.
connections.
NOTICE If inlet screen is damaged or missing, DO NOT use pressure
washer, call 1-800-743-4115.
Inspect garden hose inlet screen (K) for damage. 2.
16
Clean screen if necessary. Refer to operator’s manual for instructions.3.
Run cold water through garden hose for 30 seconds to clean out 4.
any debris. Garden hose length must not exceed 50 feet (15m). Turn
off water supply and attach garden hose (L) to water inlet. Tighten by
hand.
16
Start pressure washer
NOTICE You MUST connect and turn on water supply fully before
starting engine.
Turn on water supply.1.
Put on safety goggles (r).2.
Push trigger lock (red button) (M) on spray gun and pull trigger 3.
until water comes out in a steady stream. Release trigger to locked
position.
17
Attach quick connect wand (t) to spray gun (s). 4.
18
Choose Project Pro® nozzle (d) you want to use, pull back on collar 5.
of quick connect wand (t), insert nozzle and release collar. Tug on
nozzle to make sure it is securely in place.
19
Rotate fuel valve (N) to “On” position. 6.
20
Move throttle control lever (P) to “Fast” position, shown on engine 7.
as a ( ).
21
Move choke lever (R) to “Choke” position. 8.
22
When starting engine, position yourself as recommended and grasp 9.
starter grip handle and pull slowly until you feel some resistance.
Then pull rapidly to start engine to avoid kickback. After each starting
attempt, where engine fails to run, always point gun in safe direction,
press red button and squeeze spray gun trigger to release high
pressure.
23
NOTE: When engine starts, slowly move choke lever to “Run” position
as engine warms. If engine falters, move choke lever to “Choke” position,
then to “Run” position.
Point gun toward surface to be cleaned. Push trigger lock (red 10.
button) and pull trigger to begin spraying.
Stop pressure washer
Let engine idle for 2 minutes.1.
Move throttle control lever (P) on engine to SLOW (2.
) position,
then STOP ( ) position.
21
Turn off water supply.3.
Point spray gun in safe direction, press red button, and squeeze 4.
spray gun trigger to relieve retained high water pressure.
Disconnect garden hose from pump.5.
Disconnect high pressure hose from pump and gun for storage. For 6.
long term storage instructions, see operator’s manual.
Remove safety goggles.7.
You will need:
• Utility knife • 8 mm wrench • Phillips Screwdriver • Unleaded fuel • Garden hose, 50 feet (15m)or less
Items Included: Operator’s Manual (not shown)
WARNING Failure to read and follow the operator’s
manual and all operating instructions can
result in death, bodily injury, and/or property
damage.
WARNING Fuel and its vapors are flammable and
explosive. Turn off engine and wait at least
2 minutes before refueling. Let spilled fuel
evaporate before starting engine. Always allow
space for fuel expansion.
WARNING High pressure water spray can cut
through skin. Never spray people or animals,
as injury can result. Spray gun traps high
water pressure, even when engine is stopped
and water is disconnected. ALWAYS point spray gun in
safe direction, press red button and squeeze spray gun
trigger, to release high pressure, every time you stop
engine.
WARNING Outdoor use ONLY. DO NOT start or run
engine indoors or in an enclosed area, even
if windows and doors are open. Running
engines give off carbon monoxide, an
odorless, poison gas that can cause nausea, fainting or
death.
WARNING Starter cord kickback (rapid retraction)
can result in bodily injury. NEVER pull
starter cord without first relieving spray
gun pressure. Pull starter cord slowly until
resistance is felt, then pull rapidly. Kickback will pull
hand and arm toward engine faster than you can let go.
High pressure can cause spray gun to kickback. Hold
spray gun with both hands during use.
WARNING Risk of eye injury. Spray can splash back
or propel objects. Always wear safety goggles
when using this equipment or in vicinity of
where equipment is in use. Before starting
the pressure washer, be sure you are wearing adequate
safety goggles. NEVER substitute safety glasses for
safety goggles.
WARNING Outdoor use ONLY. DO NOT start or run engine indoors
or in an enclosed area, even if windows and doors are open.
Running engines give off carbon monoxide, an odorless,
poison gas that can cause nausea, fainting or death.
WARNING Risk of eye injury. Spray can splash back or propel
objects. Always wear safety goggles when using this
equipment or in vicinity of where equipment is in use.
Before starting the pressure washer, be sure you are
wearing adequate safety goggles. NEVER substitute safety glasses for
safety goggles.
WARNING Starter cord kickback (rapid retraction) can result in
bodily injury. NEVER pull starter cord without first relieving
spray gun pressure. Pull starter cord slowly until resistance
is felt, then pull rapidly. Kickback will pull hand and arm
toward engine faster than you can let go. High pressure can cause
spray gun to kickback. Hold spray gun with both hands during use.
Have Questions?
Do not return to store. We can help.
Call Customer Service Toll-Free 1-800-743-4115
or visit our website, BRIGGSandSTRATTON.COM
1
a
3
a
f
h
2
k
j
4
n
j
7
6
e1
5
a
8
B
A
C
D
m
E
m
F
e1
e2
e3
e4
22
23
14
Exhaust Port
Pointed away from
dwelling openings
21
15
16
L
13
H
J
9
10
11
12
17
M
18
19
20
K
p
b
b
p
G
e3
e2
e4
N
P
R
s
t
s
d
t
p
To Next Page
Need help?
General
