Page 3 - Manual FA01560-EN - 02/2023 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions
GENERAL PRECAUTIONS FOR INSTALLERS
Important safety instructions.
Please follow all of these instructions. Improper installation may cause serious bodily harm.
Before continuing, please also read the general precautions for users.
Only use this product for its intended purpose. Any other use is hazardous. • The manufacturer cannot be held liable for any
damage caused by improper, unreasonable or erroneous use. • This product is defined by the Machinery Directive (2006/42/EC)
as partly completed machinery. • Partly completed machinery means an assembly which is almost machinery but which cannot
in itself perform a specific application. • Partly completed machinery is only intended to be incorporated into or assembled with
other machinery or other partly completed machinery or equipment thereby forming machinery to which the Machinery Directive
(2006/42/EC) applies. • The final installation must comply with the Machinery Directive (2006/42/EC) and the European reference
standards in force. • The manufacturer declines any liability for using non-original products, which would also void the warranty.
• All oper
ations indicated in this manual must be carried out exclusively by skilled and qualified personnel and in full compli
ance
with the r
egulations in force. • The device must be installed, wired, connected and tested according to good professional pract
ice,
in compliance with the standar
ds and laws in force. • Make sur
e the mains power supply is disconnected during all installation
procedures. • Check that the temperature ranges given are suitable for the installation site. • Make sure that opening the automatic
barrier does not constitute a hazar
d. • Do not install on slopes i.e. any surfaces that are not perfectly level. • Do not insta
ll the
oper
ator on surfaces that could yield and bend. If necessary, add suitable reinforcements to the anchoring points. • Make sur
e
that no dir
ect jets of water can wet the product at the installation site (sprinklers, water cleaners, etc.). • Make sure you h
ave set
up a suitable dual-pole cut-off device along the power supply that is compliant with the installation rules. It should completely cut
off the power supply accor
ding to category III surcharge conditions. • Demarcate the entire site properly to prevent unauthoris
ed
personnel fr
om entering, especially minors. • In case of manual handling, have one person for ever
y 20 kg that needs hoisting;
for non-manual handling, use pr
oper hoisting equipment in safe conditions. • When the operator is being fixed in place, it may
be
unstable and overturn. Be car
eful and do not lean on it until it is fully fastened in place. • Use suitable protection to preve
nt any
mechanical hazar
ds due to persons loitering within the operating range of the operator. • The electrical cables must pass throu
gh
special pipes, ducts and cable glands in order to guarantee adequate protection against mechanical damage. • Make sure that the
moving mechanical parts are suitably far away from the wiring. • The electrical cables must not touch any parts that may overhe
at
during use (such as the motor and tr
ansformer). • All fixed controls must be clearly visible after installation, in a position
that allows
the guided part to be dir
ectly visible, but far away from moving parts. In the case of a hold-to-run control, this must be inst
alled at
a minimum height of 1.5 m fr
om the ground and must not be accessible to the public. • If the passage is wider than 3 m, you mus
t
use a fix
ed support for the boom. • If not already present, apply a permanent tag that describes how to use the manual r
elease
mechanism close to it. • Mak
e sure that the operator has been properly adjusted and that the safety and protection devices and
the
manual r
elease are working properly. • Before handing over to the final user, check that the system complies with the harmonise
d
standar
ds and the essential requirements of the Machinery Directive (2006/42/EC). • Any residual risks must be indicated clearl
y
with pr
oper signage affixed in visible areas, and explained to end users. • Put the machine’s ID plate in a visible place when
the
installation is complete. • If the power supply cable is damaged, it must be immediately replaced by the manufacturer or by an
authorised technical assistance centr
e, or in any case, by qualified staff, to prevent any risk. • Keep this manual inside the
technical
folder along with the manuals of all the other devices used for your automation system. • Mak
e sure to hand over to the end use
r
all the oper
ating manuals of the products that make up the final machinery. • The product, in its original packaging supplied b
y
the manufactur
er, must only be transported in a closed environment (railway carriage, containers, closed vehicles). • If the pr
oduct
malfunctions, stop using it and contact customer ser
vices at https://www
.came.com/global/en/contact-us or via the telephone
number on the website. • The manufactur
e date is provided in the production batch printed on the product label. If necessar
y,
contact us at https://w
ww.came.com/global/en/contact-us. • The general conditions of sale are given in the official C
AME price
lists.
To Next Page
Loading...
Need help?
General
