CAME RBE4RC User Manual

p.
7
7 - Manual
for the FA00067-EN
for the FA00067-EN v.
1
1- 05/2015 - © Came S.p.A. - The manual's contents may be edited at any time without notice.
MEMORIZING TRANSMITTERS IN SEQUENTIAL MODE 󱵩
-Press any key on the MASTER transmitter. After 10
seconds, the receiver's display will read Sto 1. Keep the
key pressed until the LED stays on permanently.
-Within 20 seconds, press a key on the transmitter you
want to memorize; the wording in the display will flash to
show that memorization is now complete.
-Repeat ❸ and ❹ for all transmitters you wish to add.
Control several outputs simulataneously 󱵪
The control of several operators/accessories connected
to OUT1 and OUT2 can be associated to one transmitter
button, even if they are separately associated with the
MASTER transmitter.
MEMORIZING A SECOND MASTER TRANSMITTER 󱵫
You can memorize a second MASTER transmitter among
those you have already memorized in your receiver.
☞If you repeat this procedure with another transmitter, it
will replace any previous second MASTER transmitter.
- Press a key on the transmitter that you want to memorize
as second MASTER transmitter. The display will show the
position occupied by the transmitter.
-Set DIP switch 2 to ON. The display will show the first
free position and a flashing S.
- Press 1 (UP) or 2 (DOWN) to select the position.
- Press and keep pressed the key of the first MASTER
transmitter. The display will flash the position and the letter M.
-Set DIP switch 2 to OFF.
Edit Password 󱵬
The (123) default password can be edited with a combination
of between 1 and 500.
-Set DIP switches 1 and 2 to ON; The display shows 001
and C.
Press CLEAR; the display will flash 000 and C.
-Press 1 (UP) or 2 (DOWN) to select the default password.
-Press CLEAR; the display will flash 123 and C.
Within five seconds press button 4; the display shows both
000 and - flashing.
-Press 1 (UP) or 2 (DOWN) to setup a new password. Press
CLEAR; the display will show M flashing.
-Set DIP switches 1 and 2 to OFF.
Saving data 󱵭
You can save data on the Memory Roll.
⚠
Cut off the main power supply every time you connect
or disconnect the Memory Roll card.
-Fit the Memory Roll card
into the connector.
- Power up and keep the Master transmitter's button
MASTER BARRIER the receiver's 2 button pressed
simultaneously until the letter U appears after about 10
seconds.
Release the key and button simultaneously.
The data is now transferred to the Memory Roll.
- Cut off the main power supply and remove the Memory
Roll card.
Manually memorizing a transmitter 󱵮
-Set DIP switch 2 to ON. The display will show the fi rst free
position and a fl ashing S.
-Press 1 (UP) or 2 (DOWN) to select a di erent free
position. The S fl ashes only if the position you have
selected is free.
-On the MASTER transmitter press the button that is
associated with the output to which you want to add a
transmitter; the output you have selected is displayed in
fl ashing mode.
-Within 20 seconds press the button of the new transmitter
you want to memorize; after a few seconds the displayed
wording stops fl ashing to indicate that memorization has
been successful.
- Set DIP switch 2 back to OFF again.
Deleting a transmitter 󱵯
You can delete one or more transmitters.
- Press a key on the transmitter you want to delete to
check which position it occupies in the receiver.
- Set DIP switch 1 to ON; the display shows 001 C and
stays on permanently.
- With 1 UP and 2 DOWN, select the position of the
transmitter that you want to delete.
- press any key on the Master transmitter; a fl ashing C is
displayed
- RESETDIP switch 1 to OFF.
Inhibiting the keys on one transmitter 󱵰
You can inhibit one or more buttons on a transmitter,
instead of deleting it.
- Press a button on the transmitter. The display shows
which position is occupied.
- SetDIP switch 2 to ON. The display will show the first free
position and a flashing S.
- Press 1 (UP) or 2 (DOWN) to select the positon.
The S on
the display stays lit.
- Press the button on the transmitter you want to inhibit.
The writing on the display starts flashing.
- Within ten seconds
press CLEAR; the occupied position is
again displayed and remains lit.
- Set
DIP 2 to OFF.

CAME RBE4RC Specifications

General

Brand	CAME
Model	RBE4RC
Category	Receiver
Language	English