SPEAKER CABLES
The PH50 is our standard cable when purchasing a complete sound system.
These cables feature 1/4” plugs and heavy 16 gauge copper wire. The PH50 is
adequate for lengths up to 50’ under normal use. You can DAISY-CHAIN up to one
additional speaker per cable by using the unused 1/4” OUTPUT” jack (right side)
on your speaker jack plate. Be sure to note the total impedance to the amp so it is
not lower than it’s recommended impedance. See Typical Loudspeaker Impedance
Configurations.
SUGGESTIONS FOR OPTIMAL PERFORMANCE
Raise the enclosure to the ear level of your audience for greater coverage. Use
Carvin’s optional SS20 stand. To help control feedback, use a graphic equalizer.
Keep the speakers in front of the microphone. Never direct the microphone
towards the speaker. For greater coverage, add a second speaker system 20° to
30° off axis.
MODEL 832 SPEAKER SYSTEM SPECS:
Frequency Response: 65 Hz to 17 kHz ±3 dB
Useable Low Frequency: 42 Hz (-10 dB)
Power Handling: 400w Continuous Power
Recommended Amp: 50 to 600 watts
Sensitivity: 100 dB SPL, 1 Watt @ 1 meter
Coverage Angles: 90° Horizontal, 45° Vertical
Nominal Impedance: 8Ω
Horn Driver Protection: Yes
Inputs/Outputs: Two 1/4" & Two Twist-Lok™ Connectors
Woofer Enclosure Type: Vented Box
Enclosure Covering: Black Duratuff II™
Dim/Wt: 20"W x 14"D x 26"H, 47 lbs.
Warranty: One Year
Options: Cover: CVS832, Stands: SS20
832
Serial No.
MADE
AUS
IN THE
POWER RATING: 400 Watts
PRO SOUND REINFORCEMENT
IMPEDANCE: 8 Ohms
JACKS WIRED
PARALLEL
EXT. SYSTEMINPUT
TWIST-LOK
1+
1–
SIGNAL
GROUND
2+
2–
NOT USED
NOT USED
832 FREQUENCY RESPONSE
CARVIN ENGINEERING DATA 832 SPEAKER SYSTEM INSTRUCTIONS
832
Congratulations on your selection of the 832
loudspeaker.
This 400
watt system features a large 15” woofer that delivers great bottom
end while the large radial horn delivers crystal clear treble. It’s great
for indoor or outdoor performances, churches, schools or clubs. Use
it with the optional SS20 stand. The 832 includes a built-in recessed
bracket for easy mounting to speaker stands.
RECEIVING INSPECTION
INSPECT YOUR SPEAKER FOR ANY DAMAGE which may have occurred during
shipping. If any damage is found, please notify the shipping company & CARVIN.
SA
VE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship
your unit, always use the original carton and packing material. CARVIN and the
shipping company are not liable for any damage caused by improper packing.
SA
VE YOUR INVOICE. It will be required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped
separately. Please allow several days for the rest of your order to arrive before
inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this
manual for your records. Return the warranty card with your name and comments to us.
WARRANTY
Parts and labor are covered for 1 year on manufacturer’s defects. Warranty does
not cover burned out drivers caused by excessive power or distortion, or physical
damage caused by general use, moisture or dust. CAUTION: Distortion from
power amps can destroy drivers much faster than clean power. Contact Carvin’s
Customer Service at 800-854-2235 or returnsrepairs@carvin.com. Customer is
responsible for shipping charges.
TYPICAL LOUDSPEAKER IMPEDANCE CONFIGURATIONS
Individual speaker or speaker cabinet wiring examples for total impedance.
For your records, you may wish to record the following information.
Serial No._____________________ Invoice Date_______________
SERIES CONNECTION
16Ω TOTAL IMPEDANCE
+
+
+
PARALLEL CONNECTION
4Ω TOTAL IMPEDANCE
+
+
+
8Ω TOTAL
IMPEDANCE
SERIES/PARALLEL
CONNECTION
8Ω TOTAL IMPEDANCE
+
+ +
+
+
+
+
8Ω
8Ω
8Ω
8Ω
8Ω
8Ω
8Ω
4Ω8Ω
8Ω
16Ω8Ω8Ω
REAR CONNECT PLATE
Two professional Twist-Lok™ connectors and two standard 1/4” phone jacks are
featured. Use either the 1/4” or Twist-Lok™ connectors for connecting to the
power amp and daisy chaining to an additional speakers.
76-00832 0902
12340 World Trade Drive, San Diego, CA 92128
(619) 487-1600 (800) 854-2235
www.carvin.com
See other side for SPS™ Powered Speaker operation
Twist-Lok™ & 1/4”
through connectors for
additional speakers
Twist-Lok™ & 1/4” inputs
from power amp output.
To Next Page
Need help?
General
