Cisco ASR 9906 User Manual

0/RSP0/CPU0 A9K-RSP880-LT-TR(Active) IOS XR RUN NSHUT
0/RSP1/CPU0 A9K-RSP5-TR(Standby) IOS XR RUN NSHUT
0/FT0 ASR-9910-FAN OPERATIONAL NSHUT
0/FT1 ASR-9910-FAN OPERATIONAL NSHUT
0/1/CPU0 A9K-8X100GE-TR IOS XR RUN NSHUT
0/FC0 A99-SFC-S OPERATIONAL NSHUT
0/FC1 A99-SFC-S OPERATIONAL NSHUT
0/FC2 A99-SFC-S OPERATIONAL NSHUT
0/FC3 A99-SFC-S OPERATIONAL NSHUT
0/FC4 A99-SFC-S OPERATIONAL NSHUT
0/PT0 A9K-AC-PEM-V3 OPERATIONAL NSHUT
0/PT1 A9K-AC-PEM-V3 OPERATIONAL NSHUT
Step 6 Verify RSP in slot 0 and RSP5 in slot 1 reach full synchronization (NSR-ready state) and status of ALL the
groups is Ready state. Use show redundancy command to verify the same.
Step 7 Manually copy Embedded Event Manager (EEM) scripts from RSP to RSP5 disks if applicable.
The EEM scripts are files located on RSP’s hard disk. These files are not automatically synced
between Active and Standby RSPs.
Note
Step 8 From active RSP, verify the both RSPs have synchronized the SNMP engine ID and SNMP ifindex-table
between each other:
Example:
#more disk0:snmp/ifindex-table loc 0/rsp0/cpu0
#more disk0:snmp/ifindex-table loc 0/rsp1/cpu0
#more disk0:snmp/snmp_persist loc 0/rsp0/cpu0
#more disk0:snmp/snmp_persist loc 0/rsp1/cpu0
Step 9 Perform redundancy switchover from active RSP to standby RSP5. This results in RSP5 (slot 1) becoming
active RSP and RSP (slot 0) becoming standby RP.
Example:
Router# redundancy switchover
Step 10 Verify that both the RSPs are in IOS XR RUN state using the show platform command
Example:
Router# show platform
Node Type State Config state
--------------------------------------------------------------------------------------
0/RSP0/CPU0 A9K-RSP880-LT-TR(Standby) IOS XR RUN NSHUT
0/RSP1/CPU0 A9K-RSP5-TR(Active) IOS XR RUN NSHUT
0/FT0 ASR-9910-FAN OPERATIONAL NSHUT
0/FT1 ASR-9910-FAN OPERATIONAL NSHUT
0/1/CPU0 A9K-8X100GE-TR IOS XR RUN NSHUT
0/FC0 A99-SFC-S OPERATIONAL NSHUT
0/FC1 A99-SFC-S OPERATIONAL NSHUT
0/FC2 A99-SFC-S OPERATIONAL NSHUT
0/FC3 A99-SFC-S OPERATIONAL NSHUT
0/FC4 A99-SFC-S OPERATIONAL NSHUT
0/PT0 A9K-AC-PEM-V3 OPERATIONAL NSHUT
0/PT1 A9K-AC-PEM-V3 OPERATIONAL NSHUT
Replacing Cisco ASR 9000 Series Router Components
39
Replacing Cisco ASR 9000 Series Router Components
Migrating from RSP4/RSP4-S/RSP-L to RSP5 Card

Cisco ASR 9906 Specifications

General

Brand	Cisco
Model	ASR 9906
Category	Network Router
Language	English