EasyManuals Logo

Cisco LightStream 1010 Installation Guide

Cisco LightStream 1010
12 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #6 background image
6 LightStream 1010 ATM Switch PCMCIA Flash Memory Card Installation Guide
Copying an Image into a Flash Memory Card
Copying an Image into a Flash Memory Card
With the Flash memory card formatted, you can now copy an image into it. The following procedure
assumes the following:
You have an ASP with a good image in the onboard Flash so you can start the switch.
The bootable image you want to copy to the Flash memory card exists on a TFTP server to which
you have access (meaning you know its name and have connectivity to it), and at least one
interface is available over which you can access this server.
You know the filename of the image you want to copy into the Flash memory card.
Following is the procedure for copying a file (called ls1010-wp-mz.111-3.018) into the Flash
memory card:
Step 1 Boot the switch and allow it to initialize.
Step 2 If the Flash memory card is unformatted or has been formatted on another switch, format
it using the procedure in the section “Formatting a Flash Memory Card” on page 5.
Step 3 To copy the image ls1010-wp-mz.111-3.018 to the Flash memory card, use the following
command series:
Switch> enable
Password:
Switch#dir
-#- -length- -----date/time------ name
1 5393 May 03 1996 15:32:57 startup-config
2 1814648 Jul 15 1996 10:29:34 ls1010-wp-mz.111-3.005
4248452 bytes available (3746940 bytes used)
Switch#copy tftp ls1010-wp-mz.111-3.018
Enter source file name: ls1010-wp-mz.111-3.018
4248324 bytes available on device slot0, proceed? [confirm]y
Address or name of remote host [255.255.255.255]? dirt
Translating "dirt"...domain server (171.69.2.132) [OK]
Accessing file "ls1010-wp-mz.111-3.018" on dirt.cisco.com ...FOUND
Loading ls1010-wp-mz.111-3.018 from 171.69.1.129 (via Ethernet2/0/0): !!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK - 1819888/3639296 bytes]
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
Switch#dir
-#- -length- -----date/time------ name
1 5393 May 03 1996 15:32:57 startup-config
2 1814648 Jul 15 1996 10:29:34 ls1010-wp-mz.111-3.005
3 1819888 Aug 20 1996 15:22:21 ls1010-wp-mz.111-3.018
2428436 bytes available (5566956 bytes used)
Switch#
Note In the preceding example, the exclamation points (!!!) appear as the file is downloaded, and
the “C” characters signify calculation of the checksum, which is a verification that the file has been
correctly downloaded to the Flash memory card.

Other manuals for Cisco LightStream 1010

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco LightStream 1010 and is the answer not in the manual?

Cisco LightStream 1010 Specifications

General IconGeneral
BrandCisco
ModelLightStream 1010
CategorySwitch
LanguageEnglish

Related product manuals