ComAp InteliNano NT Plus User Manual

ComAp, a.s.
Kundratka 2359/17
180 00, Praha 8
Czech Republic
InteliNano-NT Plus, SW version 1.5, ©ComAp – October 2013 1
InteliNano-NT-Plus-1.5-Fast User Guide.pdf
CAN INTERFACE
MAINS / GENERATOR
VOLTAGE
MEASUREMENT
T20 = Neutral
T21 = Phase 1
T22 = Phase 2
T23 = Phase 3
GENERATOR CURRENT
MEASUREMENT
T16 = k
T17 = l
USB interface
L
COM
H
INTPUT TERMINALS
T10 = COM for analog inputs
T11 = binary input
T12 = binary input
T13 = binary/analog input – Low Fuel Level
T14 = binary/analog input – Coolan Temperature
T15 = binary/analog input – Oil Pressure
OUTPUT TERMINALS
T04 = binary output – Starter (6A)
T05 = binary output - Fuel Solenoid (6A)
T06 = binary output (500 mA)
T07 = binary input/output (500 mA)
T08 = binary output (500 mA)
T09 = binary output (500 mA)
POWER SUPPLY, D+
T01 = BATT -
T02 = D+
T03 = BATT +
GENERATOR VOLTAGE
MEASUREMENT
T18 = Neutral / Phase 1
T19 = Phase 1 / Phase 2
InteliNano NT

Plus Fast User Guide
Typical wiring diagram
Accessing the setup mode
Ensure the engine is stopped and the controller is in Manual mode (green LED above button Auto is turned off).
If you have not configured the custom initialization (init) screen then press and hold Stop button, then briefly press ▲ button and then Auto .
If you have already created your own init screen then press and hold Stop button and then briefly press ▲, the custom init screen will appear, keep holding the Stop
button. Then press ▼ to switch LCD to default init screen, and then press Auto.
To move up and down in the setup menu use ▲ and ▼ buttons. Press Start button to select or Stop button for exit.
Basic settings
Output settings
Engine parameters and protections
Input settings
Generator protections
ECU setting
AMF(Auto Mains Failure) settings
Info
Outputs and inputs
Output
code
Output source
Type
Terminal assignment
O00
Not Used
binary
T04 , T05, T06, T07, T08, T09
O01
Starter
binary
T04
O02
Fuel Solenoid
binary
T05, T06, T07, T08, T09
O03
Stop Solenoid
binary
T05, T06, T07, T08, T09
O04
Alarm
binary
T04, T05, T06, T07, T08, T09
O05
GCB Close/Open
binary
T04, T05, T06, T07, T08, T09
O06
MCB Close/Open
binary
T04, T05, T06, T07, T08, T09
O07
Ready To Load
binary
T04, T05, T06, T07, T08, T09
O08
Prestart
binary
T04, T05, T06, T07, T08, T09
O09
ECU Power Relay
binary
T04, T05, T06, T07, T08, T09
O10
Choke
binary
O11
Glow Plugs
binary
Normally Open Contact – output
Normally Open Contact - input
button
Normally Closed Contact – output
Normally Closed Contact – output
User curves
I21
I23
I25
VDO Level %
VDO 5 Bar
VDO 40-120 °C
Datcon Level %
VDO 10 Bar
VDO 50-150 °C
Datcon 5 Bar
Datcon High °C
Datcon 7 Bar
Datcon Low °C
Datcon 10 Bar
Not selected
Not selected
Not selected
Input
code
Input source
Type
Terminal assignment
I00
Not Used
binary
T07, T11, T12, T13, T14, T15
I01
Emergency Stop
binary
T07, T11, T12, T13, T14, T15
I02
Remote Start/Stop
binary
T11
I03
Remote Start And Load
binary
T11
I04
Access Lock
binary
T07, T11, T12, T13, T14, T15
I05
AMF Blocked
binary
T07, T11, T12, T13, T14, T15
I06
MCB Feedback
binary
T07, T11, T12, T13, T14, T15
I07
GCB Feedback
binary
T07, T11, T12, T13, T14, T15
I10
External Warning 1
binary
T07, T11, T12, T13, T14, T15
I11
External Warning 2
binary
T07, T11, T12, T13, T14, T15
I12
External Warning 3
binary
T07, T11, T12, T13, T14, T15
I13
External Shutdown 1
binary
T07, T11, T12, T13,T14, T15
I14
External Shutdown 2
binary
T07, T11, T12, T13, T14, T15
I15
External Shutdown 3
binary
T07, T11, T12, T13, T14, T15
I20
Low Fuel Level
binary
T07, T11, T12, T13, T14, T15
I21
Fuel Level Analog
analog
T13, T14, T15
I22
Low Oil Pressure
binary
T07, T11, T12, T13, T14, T15
I23
Oil Pressure Analog
analog
T13, T14, T15
I24
High Coolant Temperature
binary
T07, T11, T12, T13, T14, T15
I25
Coolant Temperature Analog
analog
T13, T14, T15
I29
Fuel Level SD
binary
T07, T11, T12, T13, T14, T15
Dimensions
Case dimensions: 118mm x108mm x 40mm
Panel Cutout: 96mm x 96mm
WARNING!
If D+ is not used, connect this terminal to battery positive!

ComAp InteliNano NT Plus Specifications

General

Brand	ComAp
Model	InteliNano NT Plus
Category	Controller
Language	English