Danfoss TP9000 Si User Manual

Danfoss Randall Ltd
Ampthill Road
Bedford, MK42 9ER
Tel: 0845 1217 400
Fax: 0845 1217 515
Email: danfossrandall@danfoss.com
Website: www.danfoss-randall.co.uk
I. Temporary User Overrides
G. Programming your hot water - 24 hour mode
H. Programming your hot water - 7 day mode
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Part No. V1 02/09
A)Press the • CH/HW button until the HW mode is selected (Fig 8)
B) Press • PROG to show the 1st pre-set time (Event 1 )
C) Use • + or – buttons to adjust the TIME (press and hold to change in 10 min
increments). (Fig 9)
D) Press • NEXT to move to next preset time (Event 2) (Fig 10)
E) Repeat steps • C and D for programming Events 3, 4, 5 & 6.
To return to normal operating mode press and hold PROG until screen returns to the current
time. (Fig 12)
A)Press the CH/HW button until the HW mode is selected • (Fig 8)
B) Press PROG to show the 1st pre-set time (Event 1 Mon)•
C) Use + or – buttons to adjust the TIME (press and hold to change in 10 min •
increments). (Fig 9)
D) Press NEXT to move to next preset time(Event 2) • (Fig 10)
E) Repeat steps c and d for programming Events 3, 4, 5 & 6.•
F) To select the next day, press DAY/HOL and repeat steps c, d, and e • (Fig 11)
G) Repeat process as necessary to complete programming for all 7 days•
To return to normal operating mode press and hold PROG until screen returns to the current
time. (Fig 12)
Central Heating:
(ensure Central Heating mode is selected by using the CH/HW button)
Temporarily alter the current programmed temperature:• Simply press Λ
and V until the required temperature is selected. The unit will now maintain
this setting until the start of the next timed event at which point it will revert to
pre-programmed user settings. (Fig 13)
Temporarily override the current time period:• Pressing the +HRS BOOST
button will extend the current time/temperature period for 1,2 or 3 hours
depending on how many times it is pressed. At the end of the extended
period normal operation resumes. (Fig 13)
Frost Protection Mode: • Pressing Λ and V together puts the unit in frost
protection mode. A constant low temperature can be selected and this will be
maintained until Λ and V is pressed again to resume normal operation. (Fig 13)
Hot water:
Temporarily override the current time period: Pressing the +HRS BOOST button will
extend the current time period for 1,2 or 3 hours depending on how many times it is
pressed. At the end of the extended period normal operation resumes.
Fig. 8
Fig. 9
Temperature
adjust buttons
+hour boost
buttons
F. Programming your hot water - 5/2 day mode
Monday-Friday
A)Press the CH/HW button until the HW mode is selected • (Fig 8a)
B) Press PROG until the first preset time is selected • (Fig 8b)
C) Use + or – buttons to adjust the TIME (press and hold to change in 10 min •
increments). (Fig 9)
D) Press NEXT to move to next preset time & temp (Event 2)• (Fig 10)
E) Repeat steps c and d for programming Events 3, 4, 5 & 6.•
Saturday- Sunday
Press DAY/HOL to show 1st pre-set time (Event 1 Days Sat - Sun) (Fig 11)
Repeat steps b, c and d above to programme time and temperature events for
the weekend.
To return to normal operating mode press and hold PROG until screen returns to the current
time. (Fig 12)
(a)
(b)
IMPORTANT TO THE INSTALLER
Installers: please ensure that you have amended the remote sensor setting to
value 0 (no remote sensor). Please refer to Option 90 of the Installer Advanced
Programming (page 15) in the installation instructions.

Danfoss TP9000 Si Specifications

General

Brand	Danfoss
Model	TP9000 Si
Category	Thermostat
Language	English