Ordering numbers, Harmonic filters
Harmonic filters are used to reduce mains harmonics
• AHF 010: 10% current distortion
• AHF 005: 5% current distortion
380-415 V, 50Hz
I
AHF,N
Typical Motor Used
[kW]
Danfoss ordering number VLT 5000
AHF 005 AHF 010
10 A 4, 5.5 175G6600 175G6622 5006, 5008
19 A 7.5 175G6601 175G6623 5011
26 A 11 175G6602 175G6624 5016
35 A 15, 18.5 175G6603 175G6625 5022, 5027
43 A 22 175G6604 175G6626 5032
72 A 30, 37 175G6605 175G6627 5042, 5052
101 A 45. 55 175G6606 175G6628 5062, 5072
144 A 75 175G6607 175G6629 5102
180 A 90 175G6608 175G6630 5122
217 A 110 175G6609 175G6631 5152
289 A 132, 160 175G6610 175G6632 5202, 5252
324 A 175G6611 175G6633
370 A 200 175G6688 175G6691 5302
Higher ratings can be achieved by paralleling the filter units
434 A
250 Two 217 A units 5352
578 A 315 Two 289 A units 5452
613 A 355 289 A and 324 A units 5502
648 A 400 Two 324 A units 5552
Please note that the matching of the typical Danfoss frequency converter and filter is pre-calculated based on
400 V and assuming typical motor load (4 or 2 pole motor): VLT 5000 series is based on a max. 160 % torque
application. The pre-calculated filter current may be different than the input current ratings of VLT 5000 as stated
in the respective operating instructions, as these numbers are based on different operating conditions.
440-480 V, 60Hz
I
AHF,N
Typical Motor Used
[HP]
Danfoss ordering number VLT 5000
AHF 005 AHF 010
19 A 10, 15 175G6612 175G6634 5011, 5016
26 A 20 175G6613 175G6635 5022
35 A 25, 30 175G6614 175G6636 5027, 5032
43 A 40 175G6615 175G6637 5042
72 A 50, 60 175G6616 175G6638 5052, 5062
101 A 75 175G6617 175G6639 5072
144 A 100, 125 175G6618 175G6640 5102, 5122
180 A 150 175G6619 175G6641 5152
217 A 200 175G6620 175G6642 5202
289 A 250 175G6621 175G6643 5252
324 A 300 175G6689 175G6692 5302
370 A 350 175G6690 175G6693 5352
Higher ratings can be achieved by paralleling the filter units
506 A
450 217 A and 289 A units 5452
578 A 500 Two 289 A units 5502
648 A 600 Two 324 A units 5552
Please note that the matching of the typical Danfoss frequency converter and filter is pre-calculated based on
480 V and assuming typical motor load (4 or 2 pole motor): VLT 5000 series is based on a max. 160 % torque
application. The pre-calculated filter current may be different than the input current ratings of VLT 5000 as stated
in the respective operating instructions, as these numbers are based on different operating conditions.
VLT
®
5000 Series
MG.51.C5.22 - VLT
p
is a registered Danfoss trademark. 39
Technical data
To Next Page
Loading...
Need help?
General