Denon UCD-F10 User Manual

CAUTION:
Whenever the power switch is in
the STANDBY position. the unit is
still connected on AC line voltage
Please be sure to unplug the cord
when you leave home for, say, a
vacation.
[4]
CONNECTIONS
«For
instructions
on
connection
connecting
the
speaker
system
Connect the speaker system for the
left channel {the left side as seen from
NOTE: MO ‘plaver. fefer.t9- the, MD the front) to the “L” terminals, the
This system includes digita! circuitry which may cause player's operating instructions. speaker system for the right channel
interference such as color blotching or changes in the to the “R” terminals. Be sure to use
color on TVs. If this happens, move the system and the speaker systems with an impedance
TV as far apart as possible MO playe:. video deck. LD piayer, etc of 4 ohm or greater.
and operation of an optional
Side by side instaliation
@ Disconnect the ground cord if
humming or noise ts produced
when it is connected.
3
Power
piug
Use
a
record
player
with
an
FM
antenna
AC
230
V
50
Hz
(Plug into a power outlet.)
MM cartridge
install the sets as shown in
one of these diagrams. In
either case, be sure that the
pre-main amplifier's ventila-
tion holes are not obstructed.
AM loop antenna
Record player
AUDIO OUT
, Power cord
{ {for U.K. model)
Pre-main amplifier (UPA-F10}
AC outlets are not
included on U.K.
models.
Side by side instailation
CD player (UCD-F10)
Cassette deck
(UOR-F10)
System
operations
OPTICAL
DIGITAL
OUT
jack
Such
system
operations
as
the
timer
and
the
auto
Digital
data
is
output
in
optical
form
from
this
jack.
on
functions,
as
weil
as
remote
control
operations
cannot
be
performed
unless
ail
the
RCA
pin-plug
NOTES:
Do
not
plug
the
power
cord
into
the
power
outlet
until
all
connections
are
completed.
Be
sure
to
interconnect
the
channels (L to L (white) and R to R {red)) properly, as shown on the diagram.
e Insert the plugs securely. incomplete connections may result in noise.
cords
and
system
connector
cords
are
connected
PROCESSOR
LOOP
jacks
©
Be
sure
to
connect
the
speaker
cords
between
the
speaker
terminals
and
the
speaker
systems
with
the
same
between
the
units,
so
be
sure
to
make
all
the
The
PROCESSOR
LOOP
jacks
on
the
UPA-F10
are
polarities
(+
to
+,
-
to
-).
if
the
polarities
are
switched,
the
sound
at
the
center
will
be
weak,
the
position
of
the
connections
properly
as
shown
in
the
diagram.
interconnected
with
short-circuiting
pins.
Only
remove
different
instruments
will
De
unclear,
and
the
stereo
effect
will
be
fost.
,
'
Also,
disconnecting
system
connectors
while
the
these
pins
when
using
these
jacks
for
connection
to
©
After
unplugging
the
power
cord,
wait
about
5
seconds
before
piugging
it
back
in.
; ;
system is operating may result in malfunction. Be another component. e Note that setting the connection cords (pin-plug cords) next to the power cords may result in humming or other
sure to turn unplug the power cord before chan- Noise.
ging connections.
NOILOSS IWH4aNI9D
ea) LR Sp a r

Denon UCD-F10 Specifications

General

Brand	Denon
Model	UCD-F10
Category	Stereo System
Language	English