EasyManuals Logo
Home>Efco>Brush Cutter>DS 3500 T

Efco DS 3500 T Operators Instruction Book

Efco DS 3500 T
66 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #11 background imageLoading...
Page #11 background image
27
GB
CAUTION:
- Match your fuel purchases to your
consumption; don’t buy more than you will
use in one or two months;
- Store gasoline in a tightly-closed container
in a cool, dry place.
CAUTION - For the mixture, never use a
fuel with an ethanol percentage higher than
10%; gasohol (mixture of gasoline and
ethanol) up to 10% ethanol or E10 fuel are
acceptable.
NOTE - Prepare only the quantity of mixture
required for immediate use; do not leave fuel in
the tank or a container for a long time. Were
commend the use of the additive Emak ADDITIX
2000 code 001000972 if the mixture is to be
stored for 30 days.
Alkylate gasoline
CAUTIONS Alkylate fuels have
different density than normal fuel. Therefore
engines, set with normal fuel, need different
H jet regulation to avoid critical issues. For
this operation it’s necessary turned at a
Licensed Service Dealer.
Filling the tank
stir the mixture well before refuelling.
STARTING
Before starting the engine, make sure
that the blade is free to move and is not in
contact with any foreign objects.
The cutting attachment must not rotate
when the engine is idling. Otherwise contact
an Authorized Service Center to carry out a
check and x the problem.
WARNING: Hold the brush cutter rmly
with both hands. Always keep your body is to
the left of tube. Never use a cross-handed grip.
Left-handers should follow these instructions
too.
Keep a proper cutting stance.
· Never place the machine in a combustible
area such as dry leaves, straw, paper, etc.
· Store the unit and fuel in an area where fuel
vapors cannot reach sparks or open flames
from water heaters, electric motors or
switches, furnaces, etc.
· Never take the cap off the tank when the
engine is running.
· Never use fuel for cleaning operations.
· Take care not to get fuel on your clothing
OIL
2%-50 : 1
4%-25 : 1
1
5
10
15
20
25
GASOLINE
l
0,04 (40)
0,20 (200)
0,40 (400)
0,60 (600)
0,80 (800)
1,00 (1000)
0,02 (20)
0,10 (100)
0,20 (200)
0,30 (300)
0,40 (400)
0,50 (500)
l (cm
3
) l (cm
3
)
A
This product is powered by a 2-cycle engine and
requires pre-mixing gasoline and 2-cycle oil.
Pre-mix unleaded gasoline and 2-cycle engine
oil in a clean container approved for gasoline.
RECOMMENDED FUEL: THIS ENGINE IS
CERTIFIED TO OPERATE ON UNLEADED
GASOLINE INTENDED FOR AUTOMOTIVE USE
WITH AN OCTANE RATING OF 89 ([R + M] / 2) OR
HIGHER.
Mix 2-cycle engine oil with gasoline according to
the instructions on the package.
We strongly recommend the use of 2% (1:50)
Efco - Oleo-Mac two cycle engine oil, which is
specifically formulated for all air-cooled two-
stroke engines.
The correct oil / fuel proportions shown in the
table (Fig. A) are suitable when using the
PROSINT 2 and EUROSINT 2 or an equivalent
high-quality engine oil (JASO specification FD
or ISO specification L-EGD). When oil
specifications are NOT equivalent or unknown
use 4% (1:25) oil / fuel mixing ratio.
CAUTION: DO NOT USE AUTOMOTIVE
OIL OR 2-CYCLE OUTBOARD OIL.

Other manuals for Efco DS 3500 T

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Efco DS 3500 T and is the answer not in the manual?

Efco DS 3500 T Specifications

General IconGeneral
BrandEfco
ModelDS 3500 T
CategoryBrush Cutter
LanguageEnglish

Related product manuals