1
PACKING LIST
PREPARING FILTER INSERTS. All filters must be rinsed thoroughly.
Biological C-Nodes
Using the tab, pull open the Trickle Chamber Cover and remove it. Lightly rinse the C-Nodes with aquarium
water or replace 1/2 the quantity every 6 months. Never replace all the C-Nodes at one time, as the valuable
colonies of beneficial bacteria would be lost. For best results, completely fill the cartridge with additional
C- Nodes, but be sure to allow the cover to close easily.
Impeller and Motor
Unplug the power cord. Remove cover, filter baskets and discard water remaining in filter case. Remove motor
by twisting a 1/4 – turn gently in the direction of the arrow on the motor. Ease the motor down slowly to prevent
damage to the filter and motor guide. Pull impeller out of the impeller well, and rinse to remove accumulated
slime deposits. If the impeller well needs cleaning, scrub it gently with a Fluval Cleaning Brush (sold separately).
A cotton swab or impeller well brush (not supplied) can be used to remove more stubborn deposits. It is
recommended to wet motor seal ring to prevent damage before placing into filter case.
Note: It is recommended to replace the motor O-Ring on a yearly base to prevent leaking.
Re-position the magnetic impeller on the shaft and insert into the impeller well. Re-position the motor in the
filter case.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
- To guard against injury, basic safety precautions should be observed, including the following:
1. For the complete enjoyment, use and understanding of this product,
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
and all-important notices on the Power Filter before using.
Failure to do so may result in damage to the unit.
2.
DANGER
— to avoid possible electrical shock, special care should be taken since water is employed
in the use of this equipment. For each of the following situations, do not attempt repairs yourself;
return the Fluval Power Filter for repair to an authorized service facility for service or discard the
appliance.
I. If the Fluval Motor Unit falls into the water
DO NOT
reach for it! First unplug it and then retrieve it.
If any of the electrical components of the Power Filter get wet, unplug it immediately.
II. If the Motor Unit shows any sign of abnormal water leakage or if RCD (or GFCI- Ground Fault
Current Interrupter) switches off, disconnect the power supply cord from the wall socket and
remove pump from water.
III. Carefully examine the Power Filter after installation. It should not be plugged in if there is water on
parts not intended to be wet.
IV. Do not operate any appliance if it has a damaged cord or plug, or if it is malfunctioning or if it is
dropped or damaged in any manner. The power cord of this appliance cannot be replaced; if the
cord is damaged, the appliance should be discarded. Never cut the cord.
V. To avoid the possibility of the Power Filter’s plug or socket getting wet, position
the unit to one side of a wall mounted socket to prevent water from dripping
onto the socket or plug. A “drip loop” (A) should be arranged. The “drip loop” is
the part of the cord below the level of the socket or the connector if an extension
cord is used, to prevent water travelling along the cord and coming into contact
with the socket. If the plug or socket does get wet,
DO NOT
unplug the cord.
Disconnect the fuse or circuit breaker that supplies power to the appliance. Then
unplug and examine for presence of water in the socket.
3.
WARNING
- Close supervision is necessary when any appliance is used by or
near children. This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety. Children should be supervised to ensure that they do not play
with the appliance.
4. To avoid injury, do not contact moving parts or hot parts such as heaters, reflectors, lamp bulbs,
impeller etc...
5.
CAUTION
— Always unplug or disconnect all appliances in the aquarium from electrical supply
before placing hands in water, before putting on or taking off parts and whilst the equipment is being
installed, maintained or handled. When inserting or removing the pump from the water, always pull
out the main electrical plug. Never yank cord to pull plug from outlet. Grasp the plug and pull to
disconnect. Always unplug appliances from the socket when not in use.
6. This is an aquarium filter-pump. Do not use this pump for other than its’ intended use (i.e.: do not
use in swimming pools, bathrooms, etc.). The use of attachments not recommended or sold by the
appliance manufacturer may cause an unsafe condition, and will invalidate your warranty.
C Power Filter
Instruction Manual
Quick Start Guide
Congratulations on the purchase of your new Fluval C Power Filter. Please allow
approximately 15-20 minutes for the complete installation of filter parts and
inserts. Inspect the filter for any visible signs of shipping damage, and verify
that the motor is securely fastened to the filter case. The following parts should
be included in your package.
To ensure optimal operating performance, the Fluval C Power Filter must be level.
1. Insert leveller into bottom of filter case.
2. Mount Power Filter onto rear of aquarium, and adjust leveller by turning it to the
required setting so that the filter sits perfectly in vertical position.
1. With the cover removed, fill the Power Filter case completely with water
and replace cover.
2. For the initial start-up and for a faster priming of the filter, adjust water flow control
lever on the intake “U” tube to its minimum position.
3. Plug power cord into electrical outlet. Allow a few seconds for priming
(air being expelled from the “U” tube.)
4. After priming has been completed, move adjustment control on “U” tube to adjust
water flow rate to desired output level.
(See How it Works — Patented Refiltration System.)
IMPORTANT: DO NOT OPERATE FILTER WITHOUT WATER.
For a correct filter installation, the minimum water level in the tank should be no more
than 6 cm (2.25 inches) below the aquarium rim. NOTE: For maximum filter operation
and efficiency, regular cleaning of media is recommended every two weeks.
ATTACHING LEVELING DEVICE
POWER FILTER START-UP
• Do not use this pump in swimming pools or other situations where people are immersed.
• This pump is suitable for use in water temperatures up to 35°C.
• Do not use this pump with inflammable or drinkable liquids.
7. This pump is suitable for
INDOOR HOUSEHOLD
use only. Do not install or store the appliance where it
will be exposed to the weather or to temperatures below freezing.
8. Make sure an appliance mounted on a tank is securely installed before operating it, and that the electrical
connections are in accordance with data on the rating label. Do not allow pump run dry.
9. If an extension cord is necessary, a cord with proper rating should be used. A cord rated for less amperes
or watts than the appliance rating may overheat. Care should be taken to arrange the cord so that it will
not be tripped over or pulled. The connection should be carried out by a qualified electrical installer.
10.
SAVE THESE INSTRUCTIONS
For the complete use and understanding of this power filter it is recommended that this manual is
thoroughly read and understood. Failure to do so may result in damage to this filter.
FOR AUTHORIZED WARRANTY REPAIR SERVICE
For Authorized Warranty Service please return (well packaged and by registered post) to the address below
enclosing dated receipt and reason for return. If you have any queries or comments about the operation of
this product, please let us try to help you before you return the product to your retailer. Most queries can be
handled promptly with a phone call. When you call (or write), please have all relevant information such as
model number, age of product, details of aquarium set-up, as well as the nature of the problem. When you call
(or write), please have all relevant information, such as model number and/or part numbers available, as well
as the nature of the problem.
CANADA: Hagen Industries, Consumer Repair, 3235 Guénette, Montréal QC H4S 1N2
U.S.A.: Rolf C. Hagen (U.S.A.) Corp., 305 Forbes Blvd, Mansfield, MA. 02048
UK: Rolf C. Hagen (UK) Ltd, Customer Service Department California Drive, Whitwood Ind Est., Castleford,
West Yorkshire WF10 5QH — http://hagen-uk.custhelp.com
CALL US ON OUR TOLL-FREE NUMBER: Canada only: 1-800-554-2436 between 9:00 a.m. and 4:30 p.m.
Eastern Standard Time. Ask for Customer Service.
U.S. only: 1-800-724-2436 between 9:00 a.m. and 4:00 p.m. Eastern Standard Time. Ask for Customer
Service. U.K. only: Helpline Number 01977 556622. Between 9:00 AM and 5:00 PM, Monday to Friday
(excluding Bank Holidays).
HOW IT WORKS
The Fluval C Power Filter draws water from the aquarium through the
intake tube into the motor which then pumps water out of the impeller
assembly. The motor pushes the flow of unfiltered water through filter
inserts to trap particles, debris, and purify the water. The New Fluval C
series filtration system offers the ultimate multistage filtration available
in the market: With 2 x Mechanical, 1 x Chemical and 2 x Biological,
each stage operates independently.
NEW 5 STAGE FILTRATION SYSTEM
Unsurpassed Mechanical,
Chemical, and Biological filtration
A healthy aquarium requires “beneficial” bacteria. Invisible and
harmless, beneficial bacteria are essential in the removal of toxic
ammonia and nitrite. With cartridge filtration systems, when you
throw away the cartridge, you throw away beneficial bacteria. It can take weeks for the bacteria to re-colonize,
resulting in a stressful environment. The Fluval
®
5 stage filtration system is different. Only one of the filtration
components is changed at a time. This ensures that the maximum amount of beneficial bacteria remains.
There is never a sudden depletion of bacteria so biological filtration remains always at high effective levels.
Stage 1 & 2: Mechanical — Poly/ Foam Pad
Effective mechanical filtration is essential for efficient chemical and biological filtration. The large surface area
of the Poly/Foam pad effectively performs two stages of Mechanical filtration. The first stage of porous foam
traps large particles and the second stage of dense polyester captures fine debris.
Note: The mechanical frame is equipped with a cleaning indicator (A) located on the top portion of the
frame. When fully visible (B), the mechanical Poly/Foam pad requires maintenance.
Stage 3: Chemical — Activated Carbon insert
Fluval Activated Carbon Filter Insert contains
100% premium research grade carbon.
Premium research grade carbon provides
large amounts of surface area for adsorption
of undesirable impurities. The activated
carbon filter insert removes unwanted odors,
discoloration and impurities, resulting in a
crystal clear aquarium.
Stage 4: Biological — Bio-Screen
An additional hydraulic circuit conveys part of the intake water to the NEW innovative Bio-Screen placed
at the top of the Trickle Chamber cover. Fluval’s Bio-Screen removes any debris before dripping into
the biological chamber. It also ensures that the water pumped to the Trickle Chamber is evenly spread
through all areas before it drips on the C-Nodes, which are contained in the chamber. The motion of water
dropping slowly through the grids mimics the rain. This process ensures that additional oxygen is
dissolved into the water before returning to the aquarium, for a more efficient biological filtration.
Stage 5: Biological — C-Nodes
The surface of the C-Nodes is made up of a complex pore system that provides optimal living space for
beneficial bacteria to thrive and enhance the removal of ammonia and nitrites. The new “Star Shape”
provides a higher filtration surface and more biological power than a traditional cartridge, resulting in a
healthy aquarium environment.
PATENTED REFILTRATION SYSTEM
For a healthy aquarium and clear water
Sometimes delicate fish and plants require a gentler water flow. Fluval’s patented refiltration system
allows you to control the flow rate without compromising filtration efficiency. When the flow rate is
reduced, up to 50% of the water within the filter chamber is re-processed multiple times.
More impurities are filtered out, creating a healthier tank with sparkling clean and clear water.
NOTE: A reduced flow rate is also recommended during feeding, to ensure more efficient
food consumption and less waste.
FLUVAL C POWER FILTERS FLOW RATES
MODEL # C2 C3 C4
120V 230V 120V 230V 120V 230V
gph lph gph lph gph lph
Maximum Flo Rate
119 400 153 480 264 900
Minimum Flo Rate
62 210 80 330 159 480
POWER FILTER MAINTENANCE
WARNING: ALWAYS DISCONNECT APPLIANCES IN THE AQUARIUM FROM THE ELECTRICAL SUPPLY
BEFORE PLACING HANDS IN THE WATER, BEFORE PUTTING ON OR TAKING OFF PARTS, AND
WHENEVER THE FILTER EQUIPMENT IS BEING INSTALLED, MAINTAINED OR HANDLED.
No special maintenance is required to clean the external sides of the filter, other than periodic cleaning
with a damp cloth (never use harsh chemical products or detergents). Simple lemon juice may be useful for
removing calcareous encrustation. Rinse thoroughly afterward to eliminate acid residue. Following a routine
maintenance schedule will result in a healthier aquarium, and extend the life of the filter. Fluval C Power
Filters have been designed to facilitate these tasks, as they can be done within a matter of minutes.
Poly/Foam Pad
Remove mechanical frame from the filter body
and place in an empty bucket. Remove Poly/
Foam Pad from frame, and rinse using water
taken from the aquarium. Do not use tap
water as this will kill the beneficial bacteria
in your foam. NEVER use soap or detergents
as these products could be harmful to the
inhabitants of your aquarium. After rinsing,
reinstall the Poly/Foam Pad into the mechani-
cal frame, then slide the frame into the rear
the of filter case with the cleaning indicator to
the right. Note: Make sure that the dense
polyester side is facing the grid on the frame.
For best results, replace every 4-6 weeks.
Activated Carbon Insert
Remove filter cover. Pull out
the chemical basket and
Trickle Chamber from filter
body. Separate the 2 sections,
then remove insert from
Chemical basket. Replace
with new insert. For best
results, replace every 2-4
weeks.
Bio-Screen
Remove filter cover. Using the tab, pull open the Trickle Chamber Cover and remove it. Place cover in the
sink or a bucket, and rinse with the Bio-Screen, using water taken from the aquarium. Do not use tap
water as this will kill the beneficial bacteria in your foam. For best results, replace every two to
three months.
ITEM
C2 C3 C4
A
Filter Case
A20265 A20266 A20267
B
Biological Trickle Chamber with cover
A20268 A20269 A20270
C
Chemical Basket
A20271 A20272 A20273
D
Filter Cover
A20274 A20275 A20276
E
Mechanical Frame
A20277 A20278 A20279
F
“U” Tube
A20280 A20280 A20281
G
Telescopic Intake Tube
A20282 A20282 A20283
H
Extension Tube
A20284 A20284 A20285
I
Impeller Cover Assembly
A20286 A20286 A20287
J
Impeller
A20297 A20298 A20299
K
Motor Seal Ring
A20288 A20288 A20288
L
Motor Unit
A16000 A16000 A16000
M
Leveling Device
A20290 A20290 A20290
4
5
1
3
2
(B) DIRTY(A) CLEAN
A
B
C
D
E
F
G
H
I
J
K
L
M
2
Water Intake Components
The telescopic intake tube, “U” tube and impeller cover, can be cleaned using a filter stem brush to remove any
build-up of deposits.
To remove the impeller cover assembly: gently grasp the impeller cover and pull
To insert the impeller cover assembly: place the impeller cover and gently push it down until it “clicks”.
Note: For an optimal performance it is recommended to clean the impeller cover assembly once a
year. The motor should be thoroughly cleaned every three months. When all parts have been cleaned and
thoroughly rinsed, reassemble the filter and replace onto aquarium. (See Quick Start Guide 2, 3 and 4.) Follow
operating instructions to restart and prime power filter. (See Power Filter Start-up.)
AVAILABLE SEPARATELY
Alternate Filter Inserts
We offer the following alternative chemical stage inserts as superior solutions to your filtration system.
Fluval Ammonia Remover Filter Insert
Ammonia remover is a natural ion-exchange media
designed to remove toxic ammonia as water passes
over it. Controlling ammonia levels reduces stress on
fish. Use this to provide a healthy environment when
setting up a new aquarium or maintaining one that
contains a higher than average fish stock.
Fluval Zeo-Carb Filter Insert
Zeo-Carb filter insert is a blend of premium activated carbon and ammonia remover. It collectively
eliminates impurities, odors and discoloration, while
simultaneously removing toxic ammonia, resulting in
a crystal clear and healthy aquarium. Water quality is
the most important aspect of keeping fish. Maintaining
the optimum water quality will help you keep your fish
healthy and happy, and make the aquarium a beautiful
and exciting addition to your home.
NUTRAFIN WATER CARE PRODUCTS
Nutrafin Aqua Plus
Tap Water Conditioner makes tap water safe for fish.
Nutrafin Cycle
Biological aquarium supplement introduces beneficial
bacteria to accelerate the maturation of new tanks.
FLUVAL POLY/FOAM PAD
Slide the mechanical frame out of the filter body and rinse under tap water to remove
any debris caused during shipment. Check to make sure the Poly/Foam pad is inserted
correctly, with the dense polyester side facing the grid on the frame.
FLUVAL BIO-SCREEN
Rinse Bio-Screen under tap water, and place into Trickle Chamber cover.
Note: The side with the large holes must face upwards.
FLUVAL C-NODES
Open poly bag and spread them evenly in the Trickle Chamber, then rinse under tap water.
(Aquarium water is preferable if the aquarium is already established). Replace Trickle
Chamber cover. Note: Ensure C-Nodes are well positioned inside the chamber so that the
cover closes perfectly.
FILTER INSERTS MAINTENANCE
NOTE: Regular replacement of Fluval filter inserts is essential to ensure optimum filter performance.
The Fluval Poly/Foam Pad, Activated Carbon, Bio Screen and C-Nodes should be changed alternately in order to maintain continuous biological activity. To enhance bacterial action, pour a dose
of Nutrafin Cycle Biological Aquarium Supplement onto your filter inserts each time you change the media. Follow individual packaging instructions for recommended replacement intervals.
FLUVAL ACTIVATED CARBON
Remove Activated Carbon insert from its plastic shipping bag, and rinse pouch under tap
water to remove any dust particles. Place pouch loosely into the chemical media basket.
(Do not remove carbon from porous bag).
3
1. Attach the telescopic intake tube to the “U” tube.
2. Slide the “U“ tube down into its place.
Note: For deep aquariums, an additional extension tube can be purchased
separately.
ATTACHING “U” TUBE
TROUBLE-SHOOTING & FAQs
Q. What if the power filter motor doesn’t start or makes a mechanical noise?
A. First check that all the filters’ components have been correctly installed. Then check to make sure
the impeller blades are free moving on magnet assembly.
Q. Why won’t the power filter motor re-start after performing filter insert maintenance?
A. Make sure the unit has been plugged back into the power outlet and that all parts are thoroughly
clean and replaced as directed. (See Power Filter Maintenance)
Q. What should I do if the priming process doesn’t occur?
A. Verify that:
• All parts are installed correctly
• Filter case is completely filled with water
• Unit is plugged into power outlet
• “U” tube is correctly installed
• The minimum water level inside the tank no more than 6 cm (2.25 inches) below the aquarium rim
Q. Why is the water cloudy in my new aquarium?
A. Bacterial cloudiness may occur during the first week of a new aquarium set-up and may last up to
six weeks. If the condition persists, consult your local aquarium professional.
Q. What happens if I forget to clean my filter inserts?
A. If the Power Filter is left unattended for too long, the filter inserts become clogged with debris.
The efficiency of the filtration is very low, and the filter inserts require immediate rinsing or
replacement. (See Filter Inserts Maintenance)
Q. When should I operate a reduced flow?
A. Reduced flow is most helpful during feeding times, or when the input suction or output stream is
too strong for small or delicate fish. (See How it Works — Patented Refiltration System.)
Q. Why should I use only aquarium water to rinse my filter inserts after they are installed?
A. Most cities add chlorine or other chemicals to eliminate harmful bacteria in drinking water for
human consumption. These additives, while harmless to us, are very toxic to fish.
REPLACEMENT PARTS
To re-order parts for your Fluval C Power Filter, please refer to the parts list below.
2 YEAR WARRANTY
To register your warranty on line or for more information on this and other products go to:
www.hagen.com The Fluval C Filters are guaranteed against defects in material or workmanship under
normal aquarium usage and service for 2 years. We offer a 2 year guarantee on all non-replaceable parts
which means that the filter will be repaired or replaced at the manufacturer’s discretion, free of charge,
when the complete pump is returned with proof of purchase and postage paid. This warranty does not
apply to any filter that has been subjected to misuse, negligence, or tampering. No liability is assumed
with respect to loss or damage to livestock or personal property irrespective of the cause thereof.
maximumminimum
Biological Trickle chamber
with cover
Filter Cover
Mechanical Frame
“U” Tube Telescopic Intake Tube
C-Nodes
Activated Carbon
Impeller Cover Assembly
Chemical Basket
Motor Unit with Seal RingImpeller
Bio-Screen
Poly/Foam Pad
Filter Case
Leveling
Device
After preparing filter inserts, first slide the mechanical cartridge frame into the rear
of filter case with the cleaning indicator to the right. Then slide the chemical basket
and Trickle Chamber into the filter case.
INSTALLING FILTER INSERTS
4
Removing motor Re-positioning motor
RECYCLING
This product bears the selective sorting symbol for waste electrical and electronic
equipment (WEEE).This means that this product must be handled pursuant to
European Directive 2002/96/EC in order to be recycled or dismantled to minimize its
impact on the environment. Check with your local Environmental Agency for possible
disposal instructions or take to an official council registered refuse collection point.
Electronic products not included in the selective sorting process are potentially
dangerous for the environment and human health due to the presence of
hazardous substances.
09601000 11B10
To Next Page
Need help?
General
