®
If any part is found to be defective due to faulty manufacture within
the guarantee period, Husqvarna Australia PTY/Husqvarna New
Zealand Ltd., through its Authorised Service Repairers will effect the
repair or replacement to the customer free of charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty adjustment by
the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired, taken apart or
tampered with by any person not authorised by Husqvarna Australia
PTY/Husqvarna New Zealand Ltd.
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
* This guarantee is additional to, and in no way diminishes the
customers statutory rights.
Failures due to the following are not covered, therefore it is important
that you read the instructions contained in this Operator’s Manual and
understand how to operate and maintain your machine:
Failures not covered by guarantee
* Replacing Nylon Line.
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in accordance with the
instructions and recommendations contained in this Operator‘s
Manual.
* Machines used for hire are not covered by this guarantee.
* The following items listed are considered as wearing parts and their
life is dependent on regular maintenance and are, therefore not
normally subject to a valid warranty claim: Nylon Line, Spool and
Line, Electric Mains Cable
* Caution!
Husqvarna Australia PTY/Husqvarna New Zealand Ltd. does not
accept liability under the warranty for defects caused in whole
or part, directly or indirectly by the fitting of replacement parts or
additional parts that are not either manufactured or approved by
Husqvarna Australia PTY/Husqvarna New Zealand Ltd., or by the
machine having been modified in any way.
Guarantee & Guarantee Policy
Original Instructions
5857342-02 06/2015
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
Copyright © 2015 Flymo S.A. All rights reserved. Flymo
®
and other product and feature names are registered or
unregistered trademarks of Flymo S.A.
Technical data
IMPORTANT INFORMATION
Read before use
& retain for future reference
Contour
500E/580E/650E
• Awareness of the environment must be considered when disposing
of ‘end-of-life’ product.
• If necessary, contact your local authority for disposal information.
The symbol
on the product or on its packaging indicates that
this product may not be treated as household waste. Instead it shall
be handed over to the applicable collection point for the recycling of
electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste
handling of this product.
For more detailed information about recycling of this product, please
contact your local council office, your household waste disposal service
or the shop where you purchased the product.
Environmental Information
Husqvarna AB
S-561 82 Huskvarna
Sweden
Replacement Parts
Spool and Line
Reference: 500E FLY021
580E 650E FLY061
Part no.: 513937190
Part no.: 510245990
1
Carton Contents
IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product.
IF ANY PARTS ARE MISSING CONTACT:-
Husqvarna Australia PTY. Ltd., Customer Service Department direct, Telephone: 024352 7400
Husqvarna New Zealand Ltd., Customer Service Department direct, Telephone: 99202410
Safety
General
1. This product is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
the use of the product by a person responsible for their
safety. Children should be supervised to ensure that they
do not play with the product. Local regulations may restrict
the age of the operator.
2. Never allow children or people unfamiliar with the
instructions to use the machine.
3. Stop using the machine while people, especially children,
or pets are nearby.
4. Only use the trimmer in the manner and for the functions
described in these instructions.
5. Never operate the trimmer when you are tired, ill or under
the influence of alcohol, drugs or medicine.
6. The operator or user is responsible for accidents or
hazards occurring to other people or their property.
Electrical
AVOID ACCIDENTAL STARTING. REMOVE PLUG FROM
MAINS AND KEEP FEET AWAY FROM THE SWITCH
LEVER WHEN:- CLEANING AROUND THE INSIDE OF
THE SAFETY GUARD, REMOVING OR REFITTING SPOOL
CAP, MANUALLY FEEDING OR REPLACING NYLON
LINE.
1. We recommend the use of a Residual Current Device
(R.C.D.) with a tripping current of not more than 30mA.
Even with a R.C.D. installed 100% safety cannot be
guaranteed and safe working practice must be followed at
all times. Check your R.C.D . every time you use it.
2. Before use, examine cable for damage. If the cable is
found to be defective, take the product to an Authorised
Service Centre and have the cable replaced.
3. Do not use the trimmer if the electric cables are damaged
or worn.
4. Immediately disconnect from the mains electricity supply
if the cable is cut, or the insulation is damaged. Do not
touch the electric cable until the electrical supply has been
disconnected. Do not repair a cut or damaged cable.
Replace it with a new one.
5. Your extension cable must be uncoiled, coiled cables can
overheat and reduce the efficiency of your trimmer.
6. Keep the cable clear of the cutting area and obstacles at
all times.
7. Do not pull cable around sharp objects.
8. Always switch off at the mains before disconnecting any
plug, cable connector or extension cable.
9. Never pull on the cable to disconnect any of the plugs.
10. Switch off, remove plug from mains and examine electric
supply cable for damage or ageing before winding cable
for storage. Do not repair a damaged cable, replace it with
WARNING. When using the product the safety rules must be followed. For your own safety and that of bystanders
please read these instructions before operating the product. Please keep the instructions safe for later use.
Explanation of Symbols on the product
10m
12m Electric Cable
with moulded on plug
Instruction Manual
Guard
2
a new one. Use only Flymo replacement cable.
11. Always wind cable carefully, avoiding kinking.
12. Never carry the product by the cable.
13. Use only on AC mains supply voltage shown on the
product rating label.
14. Our products are double insulated to EN60335.
Under no circumstance should an earth be connected to
any part of the trimmer.
Preparation
1. While using your product always wear eye protection,
substantial footwear and long trousers. Do not operate the
equipment when barefoot or wearing open sandals.
2. Before using the machine and after any impact, check for
signs of wear or damage and repair as necessary.
3. Inspect the area to be cut before each use. Remove all
objects such as stones, broken glass, nails, wire, string
etc, which can be thrown or become entangled in the
trimmer head.
4 .
Before use, inspect the area for wildlife, especially hedgehogs.
5. Check that the cutting head is fitted correctly.
Use
1. Use the trimmer only in daylight or good artificial light.
2. Avoid operating your trimmer in wet grass, where feasible.
3. Take care in wet grass, you may lose your footing.
4. On slopes, be extra careful of your footing and wear
non-slip footwear.
5. Do not walk backwards when trimming, you could trip.
Walk never run.
6. Keep cutting head below waist level.
7. Switch off before pushing the trimmer over surfaces other
than grass.
8. Never operate the trimmer with damaged guards or
without guards in place.
9. Never fit metal cutting elements.
10. Keep hands and feet away from the cutting means at all
times and especially when switching on the motor.
11. Never pick up or carry a trimmer by the cable.
12. Do not lean over the trimmer guard - objects may be
thrown by the cutting line.
13. Beware of cut-off pieces of nylon line ejected during use.
14. Remove the plug from the mains :
- before leaving the trimmer unattended for any period;
- before clearing a blockage;
- before checking, cleaning or working on the appliance;
- if you hit an object. Do not use your trimmer until you are
sure that the entire trimmer is in a safe operating condition;
- if the trimmer starts to vibrate abnormally. Check
immediately. Excessive vibration can cause injury.
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure the
trimmer is in safe working condition.
2. Replace worn or damaged parts for safety.
3. Only use the replacement cutting line specified for this
product.
4. Only use replacement parts and accessories
recommended by Husqvarna Australia PTY/Husqvarna
New Zealand Ltd.
5. After any maintenance in dealing with the cutting line,
always return the product to its normal operating position
before switching on.
6. Clean unit with a dry cloth. Never use metal objects to
clean the unit.
7. Inspect and maintain the trimmer regularly. Any repairs
must be carried out by an authorised repairer.
8. Store in a cool dry place and out of reach of children.
Do not store outdoors.
9. Allow the product to cool for at least 30 minutes before
storing.
Cables
IMPORTANT If you want to use an extension cable when
operating your product, only the following cable dimensions
should be used.
- 1.0 mm
2
: max length 40 m
- 1.5 mm
2
: max length 60 m
- 2.5 mm
2
: max length 100 m
Minimum rating :
1.00 mm
2
size cable, 10 amps 250 volts AC.
1. YOUR PRODUCT IS SUPPLIED WITH AN ELECTRIC
MAINS CABLE WIRED DIRECTLY INTO THE
PRODUCT.
1. If the supply cord is damaged, it must be replaced by
your local Husqvarna Approved Service Centre or similarly
qualified persons in order to avoid a hazard.
2. Flymo Extension Cables are available from your local
Husqvarna Approved Service Centre.
3. Do not wire an extension cable directly to your product
yourself. Please contact your local Husqvarna Approved
Service Centre for further information on the connectors
and kits available.
4. Only use extension cables specifically designed for
outdoor use and which conform to one of the following
specifications: Ordinary rubber (60245 IEC 53), Ordinary
PVC (60227 IEC 53) or Ordinary PCP (60245 IEC 57)
CONNECTORS Flymo connectors are suitable for use
with 2 core cable only. Under no circumstances should
these connectors be used for earthed products. All Flymo
connectors and cables are of splashproof construction. They
are not waterproof and must not be left outside permanently
nor should they be submerged or immersed in water. Do not
let cable lay or trail through pools of water or splashed with
water from hose pipes.
MAINS PLUG REPLACEMENT
• If the plug supplied is cut off it should be destroyed.
There is an electric shock hazard if a cut off plug is
inserted into a 13 amp socket.
1. No earth required. Flymo products are double insulated to
EN60335 and under no circumstances should an earth be
connected to any part of the product.
2. Ensure the mains voltage suits your product.
3. IMPORTANT!
The wires in the mains lead are coloured in accordance with
the following code:
BLUE - NEUTRAL BROWN - LIVE
The wire which is coloured BLUE must be connected to the
Terminal which is marked with the letter ‘N’ or coloured BLACK.
The wire which is coloured BROWN must be connected to the
Terminal which is marked with the letter ‘L’ or coloured RED.
4. It is important that the outer sheath is clamped correctly into
the 3-pin plug.
5. If in doubt consult your local Service Repairer or qualified
electrician before the machine is used.
6. A 13 Amp fuse must be fitted to the Mains Plug.
7. The normal plug fuse and household fuse only protect
the electrical equipment and are not a safeguard against
electrocution.
If your product is hard wired i.e. non-detachable mains
electric cable, a conversion kit and extension cable is
available from all Approved Service Centres which can be
found in your local Yellow Pages.
Wheel
Trimmer Head
Assembly Instructions
A1 A2
Assembly of Switch Handle to Tube (A1)
• Ensure that the internal cable is not twisted.
1. Insert the tube into the switch handle.
2. Push until it clicks into position.
• ENSURE THAT THE TUBE IS FULLY LOCATED BY
ATTEMPTING TO REMOVE IT.
Assembly of Trimmer Head to Tube (A2)
• Ensure that the internal cable is not twisted.
1. Insert the tube into the trimmer head.
2. Push until it clicks into position.
• ENSURE THAT THE TUBE IS FULLY LOCATED BY
ATTEMPTING TO REMOVE IT.
Plant Guard
CLICK!
CLICK!
Steady Handle
Warning
Read the user instructions carefully to make sure
youunderstand all the controls and what they do.
Keep bystanders away. Do not operate whilst
people especially children or pets are in the
area.
Wear eye protection
Do not operate in the rain or leave the product
outdoors while it is raining.
Switch off! Remove plug from mains before
adjusting, cleaning or if cable is entangled or
damaged.
Warning: The cutting line continues to rotate after the
machine has been switched off.
Type CTE25 CTE27 CTE30
Width of Cut (cm) 25 27 30
Speed of Rotation of Cutting Device (rpm) 11,500 9,800 8,500
Measured Sound Power L
WA
(dB(A)) 92 91 90
Guaranteed Sound Power L
WA
(dB(A)) 96 96 96
Sound pressure L
pA
(dB(A)) 80.3 79.3 80.1
Uncertainty K
pA
(dB(A)) 2.5 2.5 2.5
Hand / arm vibration a
h
(m/s
2
) 2.0 3.6 3.0
Uncertainty K
ah
(m/s
2
) 1.5 1.5 1.5
Weight (kg) 3.1 3.2 3.4
Safety Lock-off Switch
Upper Shaft
Lower Shaft
Switch lever
5857342-02 Contour 500E-580E-650E AU/NZ.indd 1 14.06.15 11:25
To Next Page
Need help?
General
