INSTALLATION AND SERVICE MUST BE PERFORMED BY
A QUALIFIED INSTALLER.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Do not pinch the power
supply cord between the
range and the wall.
Do not seal the range to the
side cabinets.
NOTE: 24" (61 cm)
minimum clearance
between the cooktop and
the bottom of the cabinet
when the bottom of wood
or metal cabinet is
protected by not less than
1/4" (0.64 cm) flame
retardant millboard
covered with not less than
No. 28 MSG sheet metal,
0.015" (0.4 ram) stainless
steel, 0.024" (0.6 ram)
aluminum, or 0.020" (0.5
mm) copper.
30" (76.2 cm) minimum
clearance when the
cabinet is unprotected.
OoorOpen
(see note) _-e_
. J
\
NOTE: For 29" (73.7 cm) cutout wide
opening, you must call for optional
side panels and clear wide cooktop , /_30" Min.
rim as shown in the "Countertop 1___.2 cm) Mlin.
Preparation" section (see page 6). _ / 13"
\ /33cm/
_, (76.2 cm) Min.* 'r
Shave Raised ___, I 18" Min.
Edge To Clear I J_E_'_J_._..._ (45.7 cm) Min.
31 1/2"(81cm) 1 1/2" Max. / --L_-_........__ i
Wide Cooktop (3.8cm Max.) _ ......... _1___
Rim. _ ..... iF:...... i -
zG ----_L..jj i
Locate Cabinet Doors _ _'__iiiii_;:; /
l"(2.5cm) Min. __ T_ / ............... /_/ 24" Min.
From Cutout Opening _t___ / \(61 cm) Min.
Grounded Junction Box or Wall Outlet Should Be
Located 8" to 17" (20.3 - 43.2 cm) From Right
Cabinet and 2" to 4" (5.1-10.2 cm) From Floor
1 5/16"
cm)
• NOTE: Allow at least 19 ¼" (48.9 cm) clearance for
door depth when it is open.
22 7/8" **
(58.1 cm) min.
_23 1/4" _
(59.05 cm) max. [-
l
For cutouts below
22 7/8"(58.1 cm),
appliance will
slightly show out
of the cabinet. FRONT
OF
IMPORTANT: CABINET
_1 1/8"
(2.86 cm)
GR_
For width cutout (F dimension) more than 30 1/16"
(76.4 cm) to avoid glass breakage, make sure the
appliance is center in the counter opening, Raise
leveling legs at maximum position, insert the appliance
in the counter and then level. Make sure the unit is
supported by the leveling legs not by the smoothtop
glass itself.
H. HEIGHT
30 _+1/16" 21 3/4" (55,2 cm) Min. 36" (91,4 cm) standard
35 3/8" (90 crn) - 36 3/8" (92 crn) 30" (76,2 cm) 28 5/16" (71,9 crn) (76,2 _+0,15 crn) 22 1/8" (56,2 cm) Max. 35 3/8" (90 cm) rnin.
G. Minimum cutout depth is increased to 24" (61 cm) with backguard.
PIN 318201606 (0311) Rev. B
English - pages 1-9
Espahol - paginas 10-18
Fran_ais - pages 19-27
To Next Page
Need help?
General
