- 28 -
19) BAT (Battery)
The battery provides power to keep the values (such as BIOS conξΏgurations, date, and time information)
in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low
level, or the CMOS values may not be accurate or may be lost.
You may clear the CMOS values by removing the battery:
1. Turn off your computer and unplug the power cord.
2. Unplug the the battery cable from the battery cable
header and wait for one minute.
3. Plug in the battery cable.
4. Plug in the power cord and restart your computer.
β’ Always turn off your computer and unplug the power cord before replacing the battery.
β’ Replace the battery with an equivalent one. Damage to your devices may occur if the battery is
replaced with an incorrect model.
β’ Contact the place of purchase or local dealer if you are not able to replace the battery by yourself
or uncertain about the battery model.
β’ Used batteries must be handled in accordance with local environmental regulations.
1
(+)
2
(-)
Pin No. DeξΏnition
1 (+) RTC Power
2 (-) GND
F_USB30
F_ξUξξξξξξ
ξB_ξξξ ξ
F_ξ ξξξξξξξξ F_ξ ξξξξ
ξξξξξξξξξ
ξξξξ_ξξξ
ξξξξξξBξ
BξξS_ξξ
ξξξξξξBξ
SξB_ξξξ
ξξξξξξBξ
ξξξ_ξξξS
ξξ
ξξS_ξξ
ξξξξ_ξξξ
ξξξξξξBξ
ξξξ_ξξU
ξξξ_ξξξ
ξξξξξξBξ
ξξξ
ξξξξξξξξξ
ξ ξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξξ
ξξξξξξξξξξξξξξξξξξξξξξSξ ξξ ξξξξξξξξξξ
ξξ ξ
123
ξξ ξ
123
ξξ ξ
123
ξξ ξ
123
1
1
1
1
BξξSξSξξξξξξξξξξξξξξξξξ
ξξξξSξξξξξξξξξξξξξξξ
ξ_Sξ ξξ
ξξξξSξξξξξξξSξξξξξξξξUξξξ
ξξ ξ
1 2 3 ξ ξ
ξ ξξξξξξξξξξξξξξξξξξξξξξξξξξξξξSξξξξξξ3ξ
BξξSξSξξξξξξξξξSξξξ
ξξξξ
ξξξξξξξξξξξξξξξξξξξUξξξ
ξξ ξ_ξξξ_ξξ 3
F_USB3ξξFξξξξξξξξξξξ
Sξ ξξ _ξξξξξξξ
Sξ ξξ _ξξξξξξξ
Sξ ξξ _ξξξξξξξ
ξξξξξξξξξξξξξξξξξξξξξξξξSξξξFξξξξξ
ξξξ
ξξξξξξξξξ
ξξB_ξ
ξξB_ξ
ξξξξξξξFξ
ξξ_ξ0ξ
Sξξξξξξξ
Sξξξξ
ξξ_ξ0ξξξξξξξξξFξξξξξξξξ
ξξ_ξξFξ
ξξξ_ξξξξξξξξξξ
ξ_ξξξξξξξξ
ξξ_ξξξξξξ_Bξ
ξξξ
ξξξξξξξξξ
Uξξ
Sξ ξξ _Sξξ
ξξξ_ξξξξξξξξ
SξξξF_ξξξξξξξξξ
Bξ ξ
USBξ0_ξB
ξξB_ξ
ξξB_ξξ
F_USB3ξξ
ξξξ
F_USB30ξ3ξξ
ξξξξ
ξξξ_ξξξ
ξξξξξξ
ξξ_3ξξξξξξξξξξξξξξUξ
Sξξ_ξξξ
ξξ_Sξ
SξS_F ξξ
ξξξ_ξξξ
ξξξ_ξξξ
Fξ ξξξξξξξξξξξ
ξξξ_SB
18) CLR_CMOS (Clear CMOS Jumper)
Use this jumper to clear the BIOS conξΏguration and reset the CMOS values to factory defaults. To clear
the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds.
β’ Always turn off your computer and unplug the power cord from the power outlet before clearing
the CMOS values.
β’ After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or
manually conξΏgure the BIOS settings (please navigate to the "BIOS Setup" page of GIGABYTE's
website for more information).
Open: Normal
Short: Clear CMOS Values