要求： 成品尺寸285*210mm，80G书写纸，单色双面印刷。
印刷成品必须按我司提供的文档1:1印刷,成品要印刷清晰,整洁,
不能有模糊,残缺、等现象.
常规
CK面板灯通用
说明书
80G
书写纸
骆韦东
2019.09.10
折叠后效果
L
ED PANEL LIGHT USER GUIDE
L USER GUIDEED PANEL LIGHT
1:1
7-123104-1000001
HUP-PL6060-CK-H0028B2
惠州民爆光电技术有限公司
Hu
更改线条图
B1
增加安装前验证是否变形的步骤
B2
285mm
210mm
WARNING:
1.Switch off before installation.
2.Switch on only after complete installation and examination of the circuit.
Installation Procedure
Safety Instruction:
Recessed
④ Make sure the led panel light
is firmly fixed, turn on the power.
AC~
① Remove the ceiling plaster
slab.
② Feed the main AC wire in
driver terminal block respectively,
connect the panel light and driver.
③ Fix the panel light into
plaster ceiling.
Basic safety precautions should always be followed when installing, including the following:
1. Read instructions carefully before installing.
2. This LED Panel requires professional installation and maintenance.
3. The power supply of the LED Panel should be powered by a dedicated external LED driver.
4. Disconnect the power supply before installing or maintenance.
5. Make sure the wires have been properly connected before powering on the device.
6. Ensure the product has enough space for heat dissipation.
7. Ensure the luminaries are never covered by any heat insulation mat or slim layer material at anytime.
8. Dimmable version could be compatible with a wide range of recommended TRIAC dimmers.
9. IP40 for indoor use only, not for damp loaction; IP54 for indoor damp location.
10. Ambient Temperature: -10℃ to + 45℃, Avoid direct sunlight.
11. Storage Conditions: Cool & dry conditions.
CAUTION:
Make sure that the mounting surface or structural member used for installation can support the weight
of LED Panel.
Recessed with frame
① Open a hole on ceiling
according to cutout size of
recessed frame.
② Fix 2pcs of clips to one side
of frame by screw, then insert
the frame into ceiling.
Suspended
①
place on the ceiling.
Fix the anchor into target
②
on the ceiling with plastic
anchor.
Fix the installation mount
Surface mounted
⑤ Make sure the frame and
panel light are firmly fixed, turn
on the power.
① Assemble the surface mounted
frame and fix by screws.
② knock the plastic
anchor into ceiling, fix the
surface mounted frame on
the ceiling by screws.
③ Unscrew the side frame then
take out, connect the panel light to
power supply, insert the panel light
into the frame.
④ Fix the side frame back by
screw.
③
suspended installation kits,adjust
the length of steel wires.
Hang the panel to ceiling with
④
driver terminal block respectively,
turn on the power.
Feed the main AC wire in
B
A
B
A
B
Lamp inspection before installation:
Take out the lamp from the box and put it in a flat table, if the lamp upwarps, please adjust the lamp with
below steps before installation:
1.Press the oposite angles at the same time;
2.Press another two oposite angles at the
same time, make sure the four angles are
flat, then start the installation.
AC~
④ Feed the main AC wire
in terminal block
respectively.
③ Fasten the frame into ceiling
by screwing another 2 pcs clips
on the other side of frame.
BALANCE
Installation Manual
BALANCE Installation Manual
LED PANEL LIGHT USER GUIDE
要求： 成品尺寸285*210mm，70G书写纸，单色双面印刷。
印刷成品必须按我司提供的文档1: 1印刷,成品要 印刷清晰,整洁,
不能有模糊,残缺、等现象.
285mm
210mm
说明 书
AK面板灯
70G
书写纸
折叠后效果
L USER GUIDEED PANEL LIGHT
WARNING:
1.Switch off before installation.
2.Switch on only after complete installation and examination of the circuit.
Installation Procedure
Safety Instruction:
Recessed
④ Make sure the led panel light
is firmly fixed, turn on the power.
① Remove the ceiling plaster
slab.
② Feed the main AC wire in
driver terminal block respectively,
connect the panel light and driver.
③ Fix the panel light into
plaster ceiling.
Basic safety precautions should always be followed when installing, including the following:
1. Read instructions carefully before installing.
2. This LED Panel requires professional installation and maintenance.
3. The power supply of the LED Panel should be powered by a dedicated external LED driver.
4. Disconnect the power supply before installing or maintenance.
5. Make sure the wires have been properly connected before powering on the device.
6. Ensure the product has enough space for heat dissipation.
7. Ensure the luminaries are never covered by any heat insulation mat or slim layer material at anytime.
8. Dimmable version could be compatible with a wide range of recommended TRIAC dimmers.
9. IP40 for indoor use only, not for damp loaction; IP54 for indoor damp location.
10. Ambient Temperature: -10℃ to + 45℃, Avoid direct sunlight.
11. Storage Conditions: Cool & dry conditions.
CAUTION:
Make sure that the mounting surface or structural member used for installation can support the weight
of LED Panel.
LED PANEL LIGHT USER GUIDE
L USER GUIDEED PANEL LIGHT
Recessed with frame
⑥ Switch on and check
for correct operation.
① Unpack box and take out
aluminum profile A - 2pcs, aluminum
profile B - 2pcs, as well as accessory
pack.
② Assembling 3 pieces aluminum
profile together with screw.
⑤ Fix the last piece of aluminum
profile with screw after panel is well
placed.
③
wire cap, adjust the length of steel
wire.
Through the steel wire into the
④
into wire locking clips, feed the
main AC wire.
Twist the wire cap to fasten it
⑤
connect the power supply.
Adjust the length of steel wires,
Recessed with frame
⑥ Turn on the power,
installation completed.
① Open a hole according
to the lamp cut out size.
② Open tha accessory pack,
fix the installation clips to the
side of lamp.
⑤ Fasten the other side
of clips.
④ Slide panel into frame
properly.
③ Fix semi-finished frame onto
ceiling with screw (Concrete ceiling
requires plastic anchor).
Suspended
①
pack from box. Fix the anchor into
target place on the ceiling.
Take out the lamp and accessory
②
the ceiling with tapping screw,fix
the wire locking clips to the
installation mount.
Fix the installation mount on
Warning:
Input wire diameter ≥0.75mm²;
Product modification and improper installation are not valid for warranty!
Note: If the diffuse d mater ial LGP is constructed from quality PS m ateri al, while discoloration of LED panel
is easily generated with ex posur e to sunlight/UV. In general installatio n area, p laces w ithout sunlight/UV,
PS is strong enough to s uppor t. However, sunlight/UV can cause discolora tion, u nder th is circumstance, we
would recommend the use of LE D panel m ade of PMMA material. Please note warranty do es not co ver
discoloration of diffus ed mate rial.
④ Fasten one side of clips
with the ceiling.
③ Connect DC wire.
AC~
7-123004-1000004
UP-PL30120-AK-010B2
B1
增加支架框 安装
单色印刷
L=BROWN
N=BLUE
L=BROWN
N=BLUE
未注公差按此 公差表
蓝娟
2019. 09.16
修 改 安 装 步 骤
B2
要求： 成品尺寸285*210mm，80G书写纸， 单色双面印刷。
印刷成品必须按 我司提供的文档1:1印刷,成品要印刷清晰,整洁,
不能有模糊,残缺、 等现象.
常规
CK面板灯通用
说明书
80G
书写纸
骆韦东
2019.09.10
折叠后效果
L
ED PANEL LIGHT USER GUIDE
L USER GUIDEED PANEL LIGHT
1:1
7-123104-1000001
HUP-PL6060-CK-H0028B2
惠州民爆光电技术有限公司
Hu
更改 线条图
B1
增加 安装前验证是否 变形的步骤
B2
285mm
210mm
WARNING:
1.Switch off before installation.
2.Switch on only after complete installation and examination of the circuit.
Installation Procedure
Safety Instruction:
Recessed
④ Make sure the led panel light
is firmly fixed, turn on the power.
AC~
① Remove the ceiling plaster
slab.
② Feed the main AC wire in
driver terminal block respectively,
connect the panel light and driver.
③ Fix the panel light into
plaster ceiling.
Basic safety precautions should always be followed when installing, including the following:
1. Read instructions carefully before installing.
2. This LED Panel requires professional installation and maintenance.
3. The power supply of the LED Panel should be powered by a dedicated external LED driver.
4. Disconnect the power supply before installing or maintenance.
5. Make sure the wires have been properly connected before powering on the device.
6. Ensure the product has enough space for heat dissipation.
7. Ensure the luminaries are never covered by any heat insulation mat or slim layer material at anytime.
8. Dimmable version could be compatible with a wide range of recommended TRIAC dimmers.
9. IP40 for indoor use only, not for damp loaction; IP54 for indoor damp location.
10. Ambient Temperature: -10℃ to + 45℃, Avoid direct sunlight.
11. Storage Conditions: Cool & dry conditions.
CAUTION:
Make sure that the mounting surface or structural member used for installation can support the weight
of LED Panel.
Recessed with frame
① Open a hole on ceiling
according to cutout size of
recessed frame.
② Fix 2pcs of clips to one side
of frame by screw, then insert
the frame into ceiling.
Suspended
①
place on the ceiling.
Fix the anchor into target
②
on the ceiling with plastic
anchor.
Fix the installation mount
Surface mounted
⑤ Make sure the frame and
panel light are firmly fixed, turn
on the power.
① Assemble the surface mounted
frame and fix by screws.
② knock the plastic
anchor into ceiling, fix the
surface mounted frame on
the ceiling by screws.
③ Unscrew the side frame then
take out, connect the panel light to
power supply, insert the panel light
into the frame.
④ Fix the side frame back by
screw.
③
suspended installation kits,adjust
the length of steel wires.
Hang the panel to ceiling with
④
driver terminal block respectively,
turn on the power.
Feed the main AC wire in
B
A
B
A
B
Lamp inspection before in stall ation:
Take out the lamp from the box and put it in a flat table, if the la mp upwa rps, pl ease ad just th e lamp wi th
below steps before installation:
1.Press the oposite angles at the same time;
2.Press another two oposite angles at the
same time, make sure the four angles are
flat, then start the installation.
AC~
④ Feed the main AC wire
in terminal block
respectively.
③ Fasten the frame into ceiling
by screwing another 2 pcs clips
on the other side of frame.
To Next Page
Need help?
General