13
ENGLISH
REMOTE CONTROL FUNCTIONS
Mute Button
: Press to mute the AVR’s speaker and headphone outputs. To
end the muting, press this button, adjust the volume, or turn off the receiver.
Channel/Page Control
: When the tuner has been selected, this control
changes a preset radio station. While operating a cable, satellite or HDTV set-
top box or a television, press these buttons to change channels.
Transport Controls
: These buttons are used to control source playback
and The Bridge III.
Record Button
: Use this button to make recordings when an audio or
video recorder is in use.
Setup Button
: Press to display the AVR’s Main Menu, or to switch the
remote to AVR device mode.
Info Settings Button
: Press to display the AVR’s Info Menu, which
contains the settings for the current source.
Sleep Settings Button
: Press to activate the sleep timer, which turns
off the receiver after a programmed period of time of up to 90 minutes.
Each press decreases the timer by 10 minutes, ending with the “Sleep Off”
message.
Zone Selector
: Use this switch to select whether AVR commands will
affect the main listening area (Zone 1) or the remote zone of a multizone
system (Zone 2). For normal operation, leave the switch in the Zone 1
position.
Learn (AVR 460 only)
: The AVR remote is capable of “learning” individual
IR codes from the original remote that came with a source device. See page
24 in the Installation section.
Zone 2 remote controL (AVR 460 only)
The Zone 2 remote control is used in the remote zone of a multizone system
with an IR receiver connected to the Zone 2 IR Input or an A-BUS device. It
may be used to control the power, volume and mute functions or to select
a source input for the remote zone, and to control a Harman Kardon source
connected to one of the AVR’s Remote IR Outputs or the A-BUS IR Output.
The Zone 2 remote may also be used in the main listening room to directly
control the AVR 460 and Harman Kardon DVD, CD or tape players. When the
Zone Selector is pressed to switch the remote to Zone 1 mode (the Zone
Indicator will turn green), the power, volume and mute controls will only
affect the main listening area. To control operation for the remote zone, press
the Zone Selector so that the Zone Indicator turns red.
The Zone 2 remote requires two AAA batteries (included) that are installed
in the battery compartment on the back of the remote. Make sure to observe
proper polarity by matching the + and – symbols on the batteries to the
symbols printed inside the compartment.
The following explanations describe the buttons that are not similar in
function to the main remote control, or are found on the Zone 2 remote
control only. For explanations of all other Zone 2 remote control functions,
see the descriptions above that cover functions that are common to the two
Remote Controls as well as functions available on the Main Remote Control
only.
Power
: Press to turn the AVR 460 on or off. The AVR also turns on its
multizone system automatically when any of the Input Selectors is pressed,
even if the AVR itself is in Standby mode. When in the main listening room,
press any Input Selector or the AVR Selector to turn on the AVR 460.
Zone Selector and Zone Indicator
: Each press of the Zone Selector
determines whether the AVR commands will affect the main listening area
(Zone 1) or the remote zone (Zone 2). The Zone Indicator will turn green when
Zone 1 has been selected, and red for Zone 2. The Zone Indicator will also light
briefly whenever any button is pressed.
Instructions for users on removal and
disposal of used batteries.
Specification of included battery types.
These symbols shown on the product, the packaging or in the manual or
separate information sheet mean that the product itself, as well as the
batteries included or built into the product, should never be thrown away
with general household waste. Take them to suitable collection points, where
proper treatment, recycling and recovery take place, in accordance with
national or local legislation, or European Directives 2002/96/EC and 2006/66/
EC.
Correct handling of the product and batteries to be disposed of helps to
save resources and prevents possible negative effects on the environment or
human health.
The batteries included with your equipment may be Alkaline, Carbon Zinc/
Manganese or Lithium (button cells) type. All types should be disposed of
according to the above instructions.
To remove the batteries from your equipment or remote control, reverse the
procedure described for inserting batteries in the Owners Manual.
For products with a built-in battery that lasts for the lifetime of the product,
removal may not be possible for the user. In this case, recycling or recovery
centers handle the dismantling of the product and the removal of the
battery. If, for any reason, it becomes necessary to replace such a battery, this
procedure must be performed by authorized service centers.
0153CSK - HK AVR460-360 OM EURO, WORK09os.indd 13 06/08/09 13:13:47
AVR 360/230 Service Manual
To Next Page
Loading...
Need help?
General
Weight and Dimensions
