HIKVISION DS-PS1-I-WB Manual

7
8
Operaon Cauon and Device Maintenance
Specificaon
Replace Baeries
- All the electronic operaon should be strictly compliance with the electrical safety regulaons, fire prevenon regula-
ons and other related regulaons in your local region.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagnesm radiaon. Avoid
the equipment installaon on vibraons surface or places subject to shock (ignorance can cause equipment damage).
- Please make sure that the power has been disconnected before you wire, install or dismantle the device.
- If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please
contact the service center.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagnesm radiaon. Avoid
the equipment installaon on vibraons surface or places subject to shock (ignorance can cause equipment damage).
- Do not place the device in extremely hot (refer to the specificaon of the device for the detailed operaon tempera-
ture), cold, dusty or damp locaons, and do not expose it to high electromagnec radiaon.
- The device for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low venlaon or heat source such as heater or radiator is forbidden (igno-
rance can cause fire danger).
- Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a
malfuncon however), and affecng the endurance of sensor at the same me.
- Improper use or replacement of the baery may result in hazard of explosion. Replace with the same or equivalent type
only. Dispose of used baeries according to the instrucons provided by the baery manufacturer.
- Do not expose the device to the corrosive gas. Otherwise the equipment damage may occur.
- Do not expose the device to the explosive situaon.
4
Hangzhou Hikvision Digital Technology CO.,Ltd. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
The device is self powered from the manufacturer.
Replace all baeries at the same me.
Do not mix old and new baeries.
CAUTION
RISK OF EXPLOSION IF BATTERY IS
REPLACED BY AN INCORRECT TYPE
DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS
CHEMICAL BURNING DANGER
DO NOT SWALLOW THE BATTERY
KEEP NEW AND USED BATTERIES
AWAY FROM THE CHILDREN
INSTALL THE BATTERIES ACCORDING
TO THE POLARITY MARK ON THE
BATTERY HOLDER. THE OPPOSITE
POLARITY MAY CAUSE DEVICE
DAMAGE
DO NOT REVERSE THE POLARITY OF
THE BATTERY
Frequency 868 MHz
Metod Two-way communicaon
Distance 1.6 KM
Indicator Red/Green/Amber
Strobe light Red/Blue
Power Baery (default power supply method)
Consumpon
Quiescent Current: 40uA
Max. 3 V/4A (alerts in volume level 3 )
Low Baery Cut Off
2.45 V
Voltage Range
Fully charged (new) to 2.45V DC (baery)
Baery life span
3 CR123A, 3 years in work status (triggered every two weeks and
alerng 90 s for each triggering)
Power switch Power switch
Tamper switch Front and rear tamper-proof
Decibel 90 to 110 db
Max. sound duraon
15min
（
900s
）
Operaon
Temperature
-10 °C to 40 °C (14 °F to 104 °F)
Operaon Humidity 10% to 90%
Dimension (W × H ×
D)
88× 88 × 32 mm (3.46" ×3.46" × 1.26"）
Weight 169.5g
Installaon Wall mounng
General
RF
Indicaon
Power
Interface
Buzzer

HIKVISION DS-PS1-I-WB Specifications

General

Brand	HIKVISION
Model	DS-PS1-I-WB
Category	Security System
Language	English