HP ProCurve 2610-24 User Manual

HP ProCurve Switch 2610 Series
7
Specifications
HP ProCurve Switch 2610-48-PWR (J9089A) HP ProCurve Switch 2610-24/12PWR (J9086A)
Ports
48 auto-sensing 10/100 ports (IEEE 802.3 Type 10Base-T, IEEE
802.3u Type 100Base-TX); Media Type: Auto-MDIX; Duplex: half or
full
24 auto-sensing 10/100 ports (IEEE 802.3 Type 10Base-T, IEEE
802.3u Type 100Base-TX); Media Type: Auto-MDIX; Duplex: half or
full
1 RJ-45 serial console port 1 RJ-45 serial console port
2 auto-sensing 10/100/1000 ports (IEEE 802.3 Type 10Base-T, IEEE
802.3u Type 100Base-TX, IEEE 802.3ab Type 1000Base-T); Duplex:
10Base-T/100Base-TX: half or full; 1000Base-T: full only
2 auto-sensing 10/100/1000 ports (IEEE 802.3 Type 10Base-T, IEEE
802.3u Type 100Base-TX, IEEE 802.3ab Type 1000Base-T); Duplex:
10Base-T/100Base-TX: half or full; 1000Base-T: full only
2 open mini-GBIC (SFP) slots 2 open mini-GBIC (SFP) slots
Physical characteristics
Dimensions
13.5(d) x 17.4(w) x 1.73(h) in. (34.29 x 44.2 x 4.39 cm) (1U height) 9.3(d) x 17.4(w) x 1.73(h) in. (23.62 x 44.2 x 4.39 cm) (1U height)
Weight
16.7 lb. (7.58 kg), Fully loaded 7.5 lb. (3.4 kg)
Memory and processor
Processor
MIPS @ 300 MHz, 16 MB flash, 128 MB SDRAM; packet buffer size:
2 MB
MIPS @ 300 MHz, 16 MB flash, 128 MB SDRAM; packet buffer size:
1 MB
Mounting
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet
(hardware included); horizontal surface mounting only
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet
(hardware included); horizontal surface mounting only
Performance
100 Mb Latency
< 6.2 µs (LIFO) < 4.1 µs
1000 Mb Latency
< 4.4 µs (LIFO) < 2.9 µs
Throughput
up to 13.0 million pps up to 9.5 million pps
Routing/Switching capacity
17.6 Gbps 12.8 Gbps
MAC address table size
8000 entries 8000 entries
Environment
Operating temperature
32ºF to 122ºF (0ºC to 50ºC) 32ºF to 122ºF (0ºC to 50ºC)
Operating relative humidity
15% to 95% @ 104ºF (40ºC), non-condensing 15% to 95% @ 104ºF (40ºC), non-condensing
Non-operating/Storage temperature
-40ºF to 158ºF (-40ºC to 70ºC) -40ºF to 158ºF (-40ºC to 70ºC)
Non-operating/Storage relative humidity
15% to 90% @ 149ºF (65ºC), non-condensing 15% to 90% @ 149ºF (65ºC), non-condensing
Altitude
up to 10000 ft. (3 km) up to 10000 ft. (3 km)
Acoustic
Power: 63.6 dB, Pressure: 56.6 dB; DIN 45635T.19 per ISO 7779 Power: 46 dB, Pressure: 38.4 dB; DIN 45635T.19 per ISO 7779
Electrical characteristics
Maximum heat dissipation
410 BTU/hr (432.55 kJ/hr), (switch-only BTU/hr: 410; combined
switch + max. PoE devices at 15.4 W: 2281 BTU/hr)
181 BTU/hr (190.96 kJ/hr), (switch-only BTU/hr: 181; combined
switch + max. PoE devices at 15.4 W: 827 BTU/hr)
Voltage
100-127 / 200-240 VAC 100-127 / 200-240 VAC
Current
7.0 / 3.5 A 3.3 / 1.7 A
Power consumption
96 W 62 W
Frequency
50 / 60 Hz 50 / 60 Hz
Notes
Maximum power rating is the worst-case theoretical maximum power
number with fully loaded PoE, 100% traffic, all ports plugged in, and
all modules populated.
Power consumption: 96 W without PoE; 590 W with PoE.
Maximum power rating is the worst-case theoretical maximum power
number with fully loaded PoE, 100% traffic, all ports plugged in, and
all modules populated.
Power consumption: 62 W without PoE; 189 W with PoE.

HP ProCurve 2610-24 Specifications

General

Brand	HP
Model	ProCurve 2610-24
Category	Switch
Language	English