JVC ca-mx55mbk User Manual

CA-MX55MBK |
Searching for Beginning of the Current Track
«ifthe tape is traveling in the forward direction, press the <4 fast-winding
button while simultaneously pressing the ft playback button.
* if the tape is traveling in the reverse direction, press the b> fast-
winding button while simultaneously pressing the <j playback button.
(deck B only)
Searching for Beginning of the Next Track
* If the tape is traveling in the forward direction, press the b> fast-
winding button while simultaneously pressing the [> playback button.
Ifthe tape is traveling inthe reverse direction, press the <4 fast-winding
button while simultaneously pressing the <q playback button. (deck B
only)
Note:
* The deck that is playing will stop if the music scan function is used on
the other deck.
The music scan function is not effective:
« When the track being scanned contains an area of low sound level.
When the blank between tracks is short.
* When there is noise, for example, a hum between tracks.
Recording a Tape
Recording Notes
* Deck Ais used for playback only, and deck B is used for both recording
and playback.
* Toreduce hiss, use the Dolby B noise reduction system.
Press the DOLBY B NR button. The indicator light will go on.
¢ Torecord on both sides A and B continuously, select reverse mode by
pressing the REV. MODE button.
* The recording level is set automatically.
¢ if the small tabs on cassette tapes which prevent accidental erasure
have been removed, the contents of the tape cannot be over-recorded
- orerased. To record or erase, cover the holes with adhesive tape. The
tab in the upper left corner controls the side facing you; and the other
tab controls the opposite side.
* Ifyou are recording an AM broadcast and you hear interference, move
the BEAT CUT switch on the rear panel of the cassette deck & amplifier
unit from Position 1 (the normal mode ) to Position 2.
Recording from Various Sources
1. Insert a cassette for recording Into deck B.
2. Select the source you are recording from.
3. Press the Pause Il button on the tape deck while simultaneously
pressing the REC/REC MUTE button.
This puts the deck B in REC/PAUSE mode.
oD Ou
RECREC MUTE
4. Start the source to be recorded.
5. Press the Play <j or t> button on the deck B to start recording.
To record on both sides of tape, start recording in the forward ( f )
direction.
6. To stop recording, press the Stop ™ button.
7. To stop recording temporarily, press the Pause It button on deck
B.
To restart recording again, press the Play button <j or >.
16
18 (No. 20342)
Dubbing a Tape
Normal-speed Dubbing
1. Insert the cassette for playback into deck A and the cassette for
recording into deck B.
* The type of tape (Normal or CrO,) used for recording mustbe the same
as that used for playback.
¢ With the Dolby system.on, tapes are recorded in the same Dolby mode
as the pre-recorded tape, regardless of whether the DOLBY B NR
button is ON or OFF (the DOLBY B NR indicator remains off while
dubbing is in progress.)
2. Press the Pause I button while simultaneously pressing the REC/
REC MUTE button on deck B.
This places deck B in REC/PAUSE mode.
3. Press the Play button > on deck A.
4. Press the Play button <j or > ( depending on which side of the
tape you want to record onto) on deck B.
The tans-to-tane recording starts
mmo tapos w ayo tovvliul iy vlai lo.
Note:
* You cannot listen to another source during normal-speed dubbing.
* To stop normal-speed dubbing before end of either the playback or
record tape, press the Stop ml buttons on decks A and B.
High-Speed Dubbing
1. Insert the cassette for playback into deck A and the cassette for
recording into deck B.
2. Press the HIGH SPEED DUBBING button on the Tape Deck. ©
The high-speed tape-to tape recording starts.
WGH'SPEED
DUBBING
Note:
« You can listen to another source while high-speed dubbing is in
progress.
¢ Tostop high-speed dubbing before reaching the end of either playback
or record tape, press the Stop ll button on deck B.
* If nearby television is on during high-speed dubbing, beeping noise
may be recorded onto the record tape. So turn off the television or move
it farther away.
3. Press the Stop @ button on deck A when you hear the end of a
track to record from many different tapes (for example, to create
a “Greatest Hits” tape).
Deck A stops playback, and deck B automatically creates about a 4
second blank, then pauses.
Note:
:
*
If
youdon’t
want
this
blank,
press
the
Pause
4§
button
on
deck
B
before
pressing
the
Stop
™@
button.
4. Put another tape In to deck A.
5. Press the HIGH SPEED DUBBING button on the Tape Deck.
The high-speed dubbing restarts.
6. To record tracks from other tapes, repeat steps 3-5.
Note:
¢ itshould be noted that it may be unlawful to re-record prerecorded
tapes, records, or discs without the consent of the owner of
copyright in the sound recording and In any copyright musical or
literary work embodied in that recording.

JVC ca-mx55mbk Specifications

General

Brand	JVC
Model	ca-mx55mbk
Category	CD Player
Language	English