13
Use Voice Recognition
1 Press and hold to enter Voice Recognition mode.
If two phones are connected, turn the volume knob to select the desired phone,
then press the knob.
2 Speak the name of the contact you want to call or the voice command to
control the phone functions.
• Supported Voice Recognition features vary for each phone. Refer to the instruction
manual of the connected phone for details.
• This unit also supports the intelligent personal assistant function of iPhone.
Store a contact in memory
You can store up to 6 contacts.
1 Press .
2 Turn the volume knob to select
[RECENT CALL]
,
[PHONEBOOK]
, or
[DIAL NUMBER]
,
then press the knob.
3 Turn the volume knob to select a contact or enter a phone number.
4 Press and hold one of the number buttons (1 to 6).
“MEMORY PX” flashes when the contact is stored.
To erase a contact from the preset memory, select
[DIAL NUMBER]
in step 2 and store
a blank number.
Make a call from memory
1 Press .
2 Press one of the number buttons (1 to 6).
3 Press the volume knob to call.
“NO PRESET” appears if there are no contacts stored.
Delete a contact
Only when
[P.BOOK SEL]
is set to
[PB IN UNIT]
.
(
➜
12)
1 Press .
2 Turn the volume knob to select
[RECENT CALL]
or
[PHONEBOOK]
, then press the
knob.
3 Turn the volume knob to select a contact or enter a phone number.
4 Press and hold G.
BLUETOOTH®
5 Turn the volume knob to select
[DELETE]
or
[DELETE ALL]
, then press the knob.
DELETE
: Selected name or phone number in step 3 is deleted.
DELETE ALL
: All names or phone numbers from the selected menu in step 2 is
deleted.
Bluetooth compatibility check mode
You can check the connectivity of the supported profile between the Bluetooth
device and the unit.
1 While pressing and holding , press and hold the volume knob for about
3 seconds.
“BLUETOOTH” Ô “CHECK MODE” appears. “SEARCH NOW USING PHONE” ]
“PIN IS 0000” scrolls on the display.
2 Search and select “JVC UNIT” on the Bluetooth device within 3 minutes.
3 Perform (A), (B) or (C) depending on what appears on the display.
(A) “PAIRING” ] “XXXXXX” (6-digit passkey): Ensure that the same passkey
appears on the unit and Bluetooth device, then operate the Bluetooth device
to confirm the passkey.
(B) “PAIRING” ] “PIN IS 0000”: Enter “0000” on the Bluetooth device.
(C) “PAIRING”: Operate the Bluetooth device to confirm pairing.
After pairing is successful, “PAIRING OK” ] “[Device Name]” appears and Bluetooth
compatibility check starts.
If “CONNECT NOW USING PHONE” appears, operate the Bluetooth device to allow
phonebook access to continue.
The connectivity result flashes on the display.
• “H.FREE OK”*
1
and/or “A.STREAM OK”*
2
] “[Device Name]” : Compatible
• “CONNECT FAIL” Ô “TRY CONNECT” : Not compatible
*
1
Compatible with Hands-Free Profile (HFP)
*
2
Compatible with Advanced Audio Distribution Profile (A2DP)
After 30 seconds, “PAIRING DELETED” appears to indicate that pairing has been
deleted, and the unit exits check mode.
• To cancel check mode, turn off the unit by pressing and holding L SOURCE.
• Delete the pairing on the Bluetooth device before pairing with this unit.
(
➜
10)
ENGLISH
EN_KD-A845BT[J]ff.indd 13EN_KD-A845BT[J]ff.indd 13 12/24/12 10:58:33 AM12/24/12 10:58:33 AM
To Next Page
Loading...
Need help?
General
