JVC KD-DB912BT User Manual

16
ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Pair and connect a Bluetooth device for the first time
1
Press B SRC to turn on the unit.
2 Search and select the name of your receiver (“KD-DB912BT”) on the
Bluetooth device.
“BT PAIRING” flashes on the display.
• For some Bluetooth devices, you may need to enter the Personal
Identification Number (PIN) code immediately after searching.
3 Perform (A) or (B) depending on what appears on the display.
For some Bluetooth devices, pairing sequence may vary from the steps
described below.
(A) “Device Name” “XXXXXX” “VOL–YES” “BACK–NO”
“XXXXXX” is a 6-digit passkey randomly generated during each
pairing.
Ensure that the passkeys appear on the unit and Bluetooth
device are the same.
Press the volume knob to confirm the passkey.
Operate the Bluetooth device to confirm the passkey.
(B) “Device Name” “VOL–YES” “BACK–NO”
Press the volume knob to start pairing.
• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN
code “0000” into the Bluetooth device.
You can change to a desired PIN code before pairing.
(Page 20)
• If only “PAIRING” appears, operate the Bluetooth device to
confirm pairing.
“PAIRING COMPLETED” appears when pairing is completed and “” will light
up when the Bluetooth connection is established.
• “
” indicator lights up to show the strength of the battery of the
connected device.
See also
[FORMAT] on page 30 for the battery and signal strength shown
on the display.
• This unit supports Secure Simple Pairing (SSP).
• Up to five devices can be registered (paired) in total.
• Once the pairing is completed, the Bluetooth device will remain registered
in the unit even if you reset the unit. To delete the paired device, see
[DEVICE DELETE] on page 20.
• A maximum of two Bluetooth phones and one Bluetooth audio device can
be connected at any time. To connect or disconnect the registered device,
see
[PHONESELECT] or [AUDIOSELECT] in [BTMODE] . (Page 20)
However, while in BT AUDIO source, you can connect to five Bluetooth
audio devices and switch between these five devices. (Page 21)
• Some Bluetooth devices may not automatically connect to the unit after
pairing. Connect the device to the unit manually.
• When the battery of the connected Bluetooth device runs low, “Device
Name”
“LOW BATTERY” appears.
• Refer to the instruction manual of the Bluetooth device for more
information.
Auto Pairing
When you connect iPhone/iPod touch to the USB input terminal, pairing
request (via Bluetooth) is automatically activated if
[AUTO PAIRING] is set to
[ON] . (Page 20)
Press the volume knob to pair once you have confirmed the device name.
Bluetooth®
JS_JVC_KD_DB912BT_E_EN_1.indd 16JS_JVC_KD_DB912BT_E_EN_1.indd 16 7/23/2019 4:59:31 PM7/23/2019 4:59:31 PM

JVC KD-DB912BT Specifications

General

DIN size	1 DIN
CD player	Yes
Impedance	4 Ω
Output power	200 W
Product color	Black
Volume control	Rotary
Disc types supported	CD
Audio output channels	4.0 channels
Equalizer bands quantity	13
Maximum power per channel	50 W
Audio formats supported	AAC, SBC
Display type	LCD
USB version	2.0
Bluetooth version	4.2
USB port position	Front
Bluetooth profiles	A2DP, AVRCP
USB connector type	USB Type-A
USB ports quantity	1
Bluetooth functions	Handsfree calling
Package weight	1600 g
AM band range	531 - 1611 kHz
FM band range	87.5 - 108 MHz
LW band range	153 - 279 kHz
Supported radio bands	FM, LW, MW

Weight and Dimensions

Weight	1200 g