JVC KD-R482 User Manual

ENGLISH
10
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
LOUDNESS
LEVEL 01 / LEVEL 02 :Boosts low or high frequencies to produce a well-
balanced sound at low volume.;
OFF :Cancels.
SUB.W LEVEL
*
4
SPK-OUT
*
5
SUB.W 00 to SUB.W +06 ( SUB.W +03 ):Adjusts the
output level of the subwoofer connected via speaker lead.
(
16)
PRE-OUT
*
6
SUB.W –08 to SUB.W +08 ( SUB.W 00 ):Adjusts the
output level of the subwoofer connected to the lineout
terminals (REAR/SW) through an external amplifier.
( 16)
SUBWOOFER SET
*
6
ON : Turns on the subwoofer output.; OFF : Cancels.
SUBWOOFER  LPF
*
4
FRQ THROUGH :All signals are sent to the subwoofer;
FRQ 55HZ / FRQ 85HZ / FRQ 120HZ :Audio signals with frequencies lower
than 55Hz/85Hz/120Hz are sent to the subwoofer.
SUB.W PHASE
*
4
*
7
REVERSE (180°)/ NORMAL (0°):Selects the phase of the subwoofer output
to be in line with the speaker output for optimum performance.
FADER
POSITION R06 to POSITION F06 ( POSITION 00 ):Adjusts the front and
rear speaker output balance.
BALANCE
*
8
POSITION L06 to POSITION R06 ( POSITION 00 ):Adjusts the left and
right speaker output balance.
VOLUME  ADJUST
LEVEL –15 to LEVEL +06 ( LEVEL 00 ):Preset the initial volume level of
each source (compared to the FM volume level). Before adjustment, select
the source you want to adjust. (“VOLADJFIX” appears if FM is selected.)
AMP  GAIN
LOW POWER :Limits the maximum volume level to 25. (Select if the
maximum power of each speaker is less than 50W to prevent damaging
the speakers.);
HIGH POWER :The maximum volume level is 35.
*
4
Displayed only when [SUBWOOFER SET] is set to [ON] .
*
5
Displayed only when [SPK/PRE OUT] is set to [SUB.W/SUB.W] .
*
6
Displayed only when [SPK/PRE OUT] is set to [REAR/SUB.W] or [SUB.W/SUB.W] .
*
7
Selectable only if a setting other than [FRQ THROUGH] is selected for [SUBWOOFER LPF] .
*
8
This adjustment will not affect the subwoofer output.
D.T.EXPANDER
(Digital Track
Expander)
ON :Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost in
audio data compression.;
OFF :Cancels.
SPK/PRE OUT
Depending on the speaker connection method, select the appropriate
setting to get the desired output. (
 Speaker output settings )
Speaker output settings
Select the output setting for the speakers [SPK/PRE OUT], base on the
speaker connection method.
Connection via lineout terminals
For connections through an external amplifier. ( 16)
Setting on
[SPK/PRE OUT]
Audio signal through lineout terminal
REAR/SW
REAR/REAR Rear speakers output
REAR/SUB.W (default) Subwoofer output
SUB.W/SUB.W Subwoofer output
Connection via speaker leads
For connections without using an external amplifier. However, with
this settings you can also enjoy the subwoofer output.
( 16)
Setting on
[SPK/PRE OUT]
Audio signal through rear speaker lead
L (left) R (right)
REAR/REAR Rear speakers output Rear speakers output
REAR/SUB.W (default) Rear speakers output Rear speakers output
SUB.W/SUB.W Subwoofer output (Mute)
If [SUB.W/SUB.W] is selected:
–
[FRQ 120HZ] is selected in [SUBWOOFER LPF] and [FRQ THROUGH] is not
available.
–
[POSITION R01] is selected in [FADER] and selectable range is
[POSITION R06] to [POSITION 00] .
JS_JVC_KD_R482_M_EN_3.indd 10JS_JVC_KD_R482_M_EN_3.indd 10 8/1/2016 11:34:22 AM8/1/2016 11:34:22 AM

JVC KD-R482 Specifications

General

Brand	JVC
Model	KD-R482
Category	Car Receiver
Language	English