12
SUB.W LEVEL
*
4
SPK-OUT
*
5
00
to
+06
(
+03
):Adjusts the output level of the
subwoofer connected via speaker lead. (
19
)
PRE-OUT
*
6
–08
to
+08
(
00
):Adjusts the output level of the
subwoofer connected to the lineout terminals (REAR/SW)
through an external amplifier. (
19
)
SUB.W
*
6
ON
/
OFF
: Turns on or off the subwoofer output.
SUB.W
LPF
*
4
THROUGH
:All signals are sent to the subwoofer. ;
LOW
55HZ
/
MID
85HZ
/
HIGH120HZ
:Audio signals with frequencies lower than
55Hz/ 85Hz/ 120Hz are sent to the subwoofer.
SUB.WPHASE
*
4
REVERSE
(180°)/
NORMAL
(0°):Selects the phase of the subwoofer
output to be in line with the speaker output for optimum performance.
(Selectable only if a setting other than [
THROUGH
] is selected for
[
SUB.W
LPF
].)
FADER R06
—
F06
(
00
):Adjusts the front and rear speaker output balance.
BALANCE
*
7
L06
—
R06
(
00
):Adjusts the left and right speaker output balance.
VOL
ADJUST –15
—
+06
(
00
):Preset the initial volume level of each source
(compared to the FM volume level). Before adjustment, select the source
you want to adjust. (“VOLADJFIX” appears if FM is selected.)
AMP
GAIN LOW
POWER
:Limits the maximum volume level to 25. (Select if the
maximum power of each speaker is less than 50W to prevent damaging
the speakers.);
HIGHPOWER
:The maximum volume level is 35.
D.T.EXP
(Digital Track
Expander)
ON
:Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost in
audio data compression.;
OFF
:Cancels.
TEL
MUTING
*
8
ON
:Mutes the sounds while using the cellular phone (not connected
through KS-BTA100).;
OFF
:Cancels.
SPK/PRE
OUT
Depending on the speaker connection method, select the appropriate
setting to get the desired output. (
Speaker output settings
)
AUDIO SETTINGS
*
4
Displayed only when [
SUB.W
] is set to [
ON
].
*
5
Displayed only when [
SPK/PRE
OUT
] is set to [
SUB.W/SUB.W
].
*
6
Displayed only when [
SPK/PRE
OUT
] is set to [
REAR/SUB.W
] or [
SUB.W/SUB.W
].
*
7
This adjustment will not affect the subwoofer output.
*
8
Does not work if [
BT
ADAPTER
] is selected for [
AUX
] in [
SRC
SELECT
]. (
4
)
Speaker output settings
Select the output setting for the speakers [
SPK/PRE OUT],
base on the
speaker connection method.
Connection via lineout terminals
For connections through an external amplifier. (
19
)
Setting on
[
SPK/PRE OUT]
Audio signal through lineout terminal
REAR/SW
REAR/REAR
Rear speakers output
REAR/SUB.W
Subwoofer output
SUB.W/SUB.W
Subwoofer output
Connection via speaker leads
For connections without using an external amplifier. However, with this
settings you can also enjoy the subwoofer output. (
19
)
Setting on
[
SPK/PRE OUT]
Audio signal through rear speaker lead
L (left) R (right)
REAR/REAR
Rear speakers output Rear speakers output
REAR/SUB.W
Rear speakers output Rear speakers output
SUB.W/SUB.W
Subwoofer output (Mute)
If [
SUB.W/SUB.W
] is selected:
– [
HIGH120HZ
] is selected in [
SUB.W
LPF
] and [
THROUGH
] is not available.
– [
R01
] is selected in [
FADER
] and selectable range is [
R06
]to [
00
].
To Next Page
Loading...
Need help?
General
