Kaabo Skywalker 8H User Manual

19 20
DISPLAY &
KEY SETTINGS
3. Power Buon. To turn the scooter on or off press buon for 2 seconds.
4. Accelerator. Pull to accelerate. The stronger you pull, the faster it
accelerates. The scooter is delivered in “Non-Zero Start” seng
(Kick-And-Go is ON), i.e. the accelerator only works if the scooter is
already in moon.
5. Mode Buon. Press to select various display opons:
Detailed P-sengs mode. To access P-sengs to make various advanced
changes, press POWER [3] and MODE [5] simultaneously for 2 seconds.
Cycle through the P-sengs using the MODE buon. To select a P-seng in
order to make changes press the POWER buon. Change the value (up or
down) using the MODE (Up) and POWER (Down) buons. To return to the
P-sengs menu aer changing a value, wait 2 seconds. To return to operang
mode, wait a further 2 seconds. Only
COMMENTMODE
TIME
Time since powering on the scooter.
TRIP Distance travelled since powering on the scooter.
ODO Total distance travelled.
VOL Current baery voltage.
CH2:00
Charging mode. Time (2 hours) scooter stays ON (overrides auto-switch off)
so you can use display’s USB port to charge e.g. your phone.
P-SETTINGS
P0
Tire diameter .
P1
Controller shut-down voltage. Default set to 52V .
P2
Motor magnec pole seng. Default is 30. Do not change.
P3
Speed signal selecon. Default is 0. Do not change.
P4
Distance / speed unit. 0=km, 1=miles
P5
Start seng. 1=non-zero start (Kick-and-Go), accelerator won’t work if scooter not in
moon; 0=immediate start (CAUTION while using this!)
P6
Cruise control. 0=cruise control OFF, 1=cruise control ON.
P7
Inial acceleraon. 0=strong, 1=so.
P8
Electric (regenerave) braking (E-ABS). 0=E-ABS off, 1=E-ABS on
P9
Speed limit as % of top speed, i.e. 100=no speed limit.
PA
Clear total distance travelled (ODO).
PB
Scooter auto-turn off me in minutes.
PC
Display brightness (1=low, 3=high)
Driving Mode Selecon
Located underneath the main display on the right side of
the handle bar you can find two switches to configure
driving modes:
The ECO/TURBO switch regulates the power of your scooter. By pressing
down the buon, ECO mode is acvated which will reduce torque and top
speed to maximize range. When the buon is not pressed, TURBO mode is
acvated and there is no restricon of power.
The SINGLE/DUAL switch toggles single or dual motor drive. By pressing down
the buon DUAL motor drive is acvated. When the buon is not pressed,
SINGLE (rear) motor drive is acvated.
For Maximum range, select ECO mode and SINGLE motor drive. For maximum
power and speed, select TURBO mode and DUAL motor drive.
Display Sengs
Scooter is equipped with the following display:
Gear change. To change the gear (1=slow, 2=medium, 3=fast), while the
scooter is powered ON, press the POWER buon to enter gear seng mode.
Press MODE to switch between gears. To return to operang mode either
press POWER or wait for 2 seconds.
1. Speedometer. Shows the speed at which you are travelling.
2. Baery Indicator. Charge your scooter frequently, do not let it run out
of baery. As a rough guideline, charge at or below 2 bars.

Kaabo Skywalker 8H Specifications

General

Brand	Kaabo
Model	Skywalker 8H
Category	Scooter
Language	English