Kenwood AR-404 User Manual

‘Resetting the Microcomputer
If the microcomputer may malfunction (unt cannot be
‘operated
or
shows
an
erroneous
dispiay
ifthe
power
cord
‘unplugged wile the power is ON, oF due to some other
fextoma factor If this happens, exacute the folowing pro
‘cedure
toreset
the
microcomputer
and
return
the
unit
tots
‘normal operating condition
For USA ond Canad
‘Unplug
the
power
cord from
the
wall
outlet.
then
ua
it
holding
down
the
POWER
ki
Except loc USA sad Canada
‘With the power cord pluggedin, ture the POWER key
OFF. Then, while holding down the ON/STANDBY
‘kay, prose the POWER key.
‘Pionse note that resetting the mcrocomputer will lear
‘the contents of the memory and returns the unt tothe
‘State was 6 when fief the factory
[No
sound
from
the
speakers.
The
spaaker
coe
tin.
“MUTE is On
‘a disconnected.
«VOLUME
i
set
to
the
minimum
pose
|
«Beet
the
volume
toa
proper
lve:
1 The SPEAKERS swiches ae sotto OFF
‘Connect
propery
refering
to
“Setting
‘up
the
system”
=
‘Turn OFF the MUTE
the SPEAKERS swcion to Ol
“The
standby
indicator
blinks
and
|
*
Speaker
cords
ae
short-cwcuted
* Turn the powe of, eliminate the shor
‘sound
is
not
output.
‘cccuting,
then
tun
on
the
power
agen
Sound
is
not
output
from
one
of
|
+The
speaker
ceria
csconnocied,
|
+
Conpwct
pope
ralring
to
“Betting
the
speakers.
‘up
the
system”
“|
"A
humming
noise
Is
generated
|
The
audio
cord
from
the
wntable
isnot
|
©
Insert
the
aude
cord
plugs
securely
into
‘Gihen
the
PHONO
inputselectorle
|
connected
to
the
PHONO
jacks
the
PHONO
jacks
elected,
«Tho
tunable
is
not
grounded
+
Connect
the
grounding
wire
tothe
GND
terminal on the rear panel. C8)
Tuner
not tuned.
‘No antenna is connected
‘The broadcast band snot set properly.
{The
frequency
of
he
dosved
stavonis
|
+
Tune
the
frequency
ofthe
desired
st
‘Connect an antenna 2
1 Set the broadcast band propery.
von
mobile.
7
Noize
due
tigation
ne
fom
an
auto-
|
©
instal
the
outdoor
antenna
away
from
«Nowe
due
to
interference
trom
an
elec:
|
«
Tura
off
the
power
tothe
appliance.
ne appliance.
‘Noise dv0 10 8 nearby TV set
‘the road
‘+nstalthe receiver farther away fom the
wv
be received by pressing the corre-
sponding numeric key:
‘Astation
which
was
preset
cannot
|
+
Theprosetstatonbelongstoafraquency
|
*Preset
a
station
with
a
recsivable
fe-
that
cannot
be
received
‘quency.
‘The
preset
memory
was
cleared
be-
|
+
Preset
the
station
again
‘cause
the
power
cord
had
been
un-
lugged
fora
long
period
of
ie,

Kenwood AR-404 Specifications

General

Brand	Kenwood
Model	AR-404
Category	Receiver
Language	English