~
K&M
KONIG
&
MEYER
~
Stands
For
Music
19790 Tablet PC stand holder
- Efficient and
flexible-
the Tablet Holder comes with a 3/8" (5/8") connection thread
- Write, read, surf, look at pictures
or
watch videos - made easy
- Equally suited for the stage, home and studio.
- For tablets of all manufacturers - not bound to a specific brand
-Screen
sizes (Width:
222-334
mm, Height:
128-232
mm)
- Helpful settings for quick setup and adjustments
- Provides any number of adjustments:
Tablet Size, Adjustment Angle, Direction, Portrait/Landscape
ATIACH
Tablet
to
the
STAND
(1)
Thank you for choosing this product. The instructions provide directions to
all
of the important setup and handling steps. We recommend you keep these
instructions for future reference.
SAFETY NOTES
When mounting the Tablet PC ensure that it is property
placed and secured according to the instructions. K&M
is not
liable in the case of improper use and associated
consequences i.e. damages!
-Only
use suitable
stands-
the prerequisites are:
I
I =
I
I ,
. I
I
I
stability, weight bearing load, centered load, 3/8" (5/8")
connectionfuffiad
,
a~K&M19~260,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
260/
1
, 20
1
A/2, 2
5
6
80
,
26085
,
26125
,
26150
, FIRST TIME PLACEMENT
of
the
Tablet
J(2-9)
·
~~;~~O:~~h~~:r
examples (Selection
of
varJ1ous
Tablets
see
262, 2625o
~
.a -
,.,.u
.c
- Place the Tablet PC carefully
in
position and 2
tighten the screws, then check that the Tablet PC * \
is securely
1n
place
~-'2J""'
.,
\'!I
adjusting settings (angle, format)
SETUP
ATTACH Tablet to the STAND (1)
1
a.
Turn the the stand's knurled disc as far
as
it will
go
onto the siand's threaded bol
b.
Screw the Tablet holder onto the threaded bolt
c.
Tighten the knurled screw to the mount
FIRST TIME PLACEMENT of the Tablet (2-9)
Many settings are possible - identify the
required settings
2 First open the three knurled pins until
there is enough room to place the tablet
3
a.
Release the upper support arm,
b.
extend it out as far as it goes and
c. tighten the
clamping screw.
4
a.
Release side support arms and ...
b
....
with the help
of
the scale symmetrically
extend to a rough position,
c. tighten both
clamping screws.
5 Place the tablet into the corner supports to
!
ensure that it fits
a.
Tablet is too narrow: Retract the support m
-··
b. Tablet is too wide: Extend the support
arms (symmetrically)
until it fits.
Tab
too
narrow
arms a bit (symmetrically) until
it
fits.
~
c.
Tablet fits, if the corner supports do not show
'<V"...__.---....,.,
any space between the tablet and the holder
..
__
..
when looking at it from the side. l w
__:J
6 a. Place the tablet in both corner supports...
.......____
6.a
b . ... and hold the tablet ·
7 Retract the upper support arm
a.
Release the clamp screw and retract the support arm ...
b
..
.. until the tablet is securely held in place.
c. Tighten the clamping screw
.
~
8 Gently clamp the tablet into the corner 8
supports by tightening the knurled pins
9 Your Tablet should be securely positioned now.
Please ensure that this is the case. :
:
a. Does the
Tablet sit securely in the holder : :
without any play? · ·
b.
Are the three knurled handles properly tightened?
c. Are the three
plastic finger screws properly tightened?
If
this is not the case, please refer to points (2-8).
---4.c
(
~
Tab
nts
9.a
To Next Page
Need help?
General
