Kyocera KM-1620 Error Code List

Downloaded from www.coronatechnical.com manuals search
engine
Kyocera KM-1620/ KM-2020 Error Code List
Self-diagnosis
(1) Self diagnostic codes
Code
Contents
Remarks
Causes
Check procedures/corrective measures
C0100
(A0100*)
Backup memory read/write problem
(main PCB)
• Read and write data does not match.
Defective backup
RAM or main
PCB.
Replace the main PCB and check for cor-
rect operation.
C0110
(A0110*)
Backup memory data problem (main
PCB)
• Data in the specified area of the
backup memory does not match the
specified values.
Problem with the
backup memory
data.
Turn safety switch off and back on and run
maintenance item U020 to set the contents
of the backup memory data again.
Defective backup
RAM.
If the C011 is displayed after re-setting the
backup memory contents, replace the
backup RAM or main PCB.
C0150
(A0150*)
Backup memory read/write problem
(engine PCB)
• Read and write data does not match.
Defective backup
RAM or engine
PCB.
Replace the engine PCB and check for
correct operation.
C016
(A016*)
Backup memory data problem (en-
gine PCB)
• Data in the specified area of the
backup memory does not match the
specified values.
Problem with the
backup memory
data.
Turn safety switch off and back on and run
maintenance item U020 to set the contents
of the backup memory data again.
Defective backup
RAM.
If the C016 is displayed after re-setting the
backup memory contents, replace the
backup RAM or engine PCB.
C0170
Accounting count problem
• When the power is turned on, the to-
tal count and the scan count are ab-
normal both on the main PCB and the
engine PCB.
Defective main
PCB or engine
PCB.
Replace the main PCB or engine PCB and
check for correct operation.
C0180
Machine number mismatch
• When the power is turned on, the ma-
chine number does not match be-
tween the main PCB and the engine
PCB.
Correct EEPROM
is not installed.
Install the correct EEPROM. If it does not
solve the problem, contact the Service Ad-
ministrative Division.
Data damage of
EEPROM.
Contact the Service Administrative Divi-
sion.
C0210
(A0210*)
Communication problem between
the main PCB and engine board PCB
• When the power is turned on, the ma-
chine does not detect the low level of
SBSY and the high level of SDIR for
three seconds.
Poor contact in
the connector ter-
minals.
Check the connection of connectors YC6
on the main PCB and YC1 on the engine
PCB, and the continuity across the connec-
tor terminals. Repair or replace if neces-
sary.
Defective main
PCB or engine
PCB.
Replace the main PCB or engine PCB and
check for correct operation.
C0410
(A0410*)
Optional DP communication problem
• Communication fails five times suc-
cessively.
DP installed incor-
rectly.
Check the installation state of the DP and
adjust it if it is not properly installed.
Defective main
PCB or DP driver
PCB.
Replace the main PCB or DP driver PCB
and check for correct operation.
“A” is displayed on the operation panel.

Kyocera KM-1620 Specifications

General

Time to first page (black, normal)	5.9 s
Print speed (black, normal quality, A4/US Letter)	16 ppm
Internal memory	32 MB
Maximum internal memory	160 MB
Custom media sizes	98x147 - 297x432 (mm)
Maximum print size	A3 (297 x 420 mm)
Standard media sizes	A3, A4, A5, Ledger, Letter, Legal, Folio
Zoom capability	50 - 200%
Maximum number of copies	250 copies
Copy speed (black, normal quality, A4)	16 cpm
Standard input capacity	300 sheets
Grayscale levels	256
Type	Digital copier
Dimensions (WxDxH)	574 x 552 x 502 mm
Number of print cartridges	1
Recommended media weight	45 - 160 g/m²
Compatible ink types, supplies	TK-410
Maximum duty cycle	20000 pages per month
Power requirements	220-240V, 50/60 Hz
Power consumption (standby)	88 W
Power consumption (typical)	356 W
Certification	GS TUV CE ISO 9001 ISO 14001

Weight and Dimensions

Weight	39000 g