Home
Lenze
Recording Equipment
E84DGFCA Series
Lenze E84DGFCA Series User Manual
4
of 1
of 1 rating
75 pages
Give review
Manual
Specs
To Next Page
To Next Page
Loading...
L
Ä.YR$ä
13564903
AS-Interface
(AS-i)
Accessories
Inverter Drives 8400 motec
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Communication Manual
EN
E84DGFCAxxx
2
Table of Contents
AS-Interface
1
Contents
2
1 About this documentation
4
1.1 Document history
6
1.2 Conventions used
7
1.3 Terminology used
8
1.4 Notes used
9
2 Safety instructions
10
2.1 General safety and application notes
10
2.2 Device and application-specific safety instructions
11
2.3 Residual hazards
11
3 Product description
12
3.1 Application as directed
12
3.2 Features and variants
13
3.3 Connections and interfaces
15
4 Technical data
17
4.1 General data and operating conditions
17
4.2 Protocol data
18
4.3 Communication time
19
5 Installation
20
5.1 Mechanical installation
21
5.2 Electrical installation
22
5.2.1 Bus cable specification
22
5.2.2 AS-i connection
23
5.2.3 Voltage supply
24
6 Commissioning
25
6.1 Before initial switch-on
25
6.2 How to configure the host (master)
26
6.3 Settings for AS-i communication in the »Engineer«
27
6.3.1 Addressing the AS-i slaves
27
6.3.2 All parameters for setting the AS-i communication
28
6.4 Initial switch-on
29
7 Data transfer
30
7.1 AS-i messages
30
7.2 AS-i cycle
32
7.3 Synchronisation
33
7.4 AS-i concept of the Communication Unit
34
7.5 Data transmission slave 1 (AS-i profile 7.A.5)
35
7.6 Data transmission slave 2 (AS-i profile 7.A.7)
37
8 Process data transfer
39
8.1 Accessing process data / PDO mapping
40
8.2 Port interconnection of process data objects (PDO)
41
9 Parameter data transfer
44
9.1 CTT2: Read parameter value
45
9.2 CTT2: Write parameter value
46
9.3 CTT2: Read code number
47
9.4 CTT2: Write code number
48
9.5 CTT2: Block parameter transfer
49
9.5.1 Read mode
49
9.5.2 Write mode
51
9.6 CTT2: Standard error codes
52
9.7 CTT2: Acyclic device error codes
53
10 Diagnostics
54
10.1 LED status displays
54
10.2 Diagnostics with the »Engineer«
55
11 Error messages
56
11.1 Short overview of the AS-i error messages
56
11.2 Possible causes and remedies
57
12 Parameter reference
61
12.1 Communication-relevant parameters of the operating system
61
C01501 | Response in case of communication fault with MCI
61
C01503 | MCI timeout
61
12.2 Parameters relevant for AS-i communication
62
C13200 | Active address
62
C13202 | Slave address EPM value
62
C13204 | Override Slave Addresses
63
C13205 | Override of slave addresses during initialisation
63
C13206 | Slave profiles
63
C13207 | Response in case of communication fault
64
C13208 | AS-i monitoring times
64
C13210 | AS-i Bus transaction counter
64
C13211 | bus status
65
C13213 | CTT2 block parameter transfer: Write parameter block configuration
65
C13214 | CTT2 block parameter transfer: Read parameter block configuration
66
C13220 | Display: Last data to master
66
C13221 | Display: Last data from master
67
C13852 | All words to standard device
67
C13853 | All words from standard device
67
C13900 | Firmware product type
68
C13901 | Firmware compilation date
68
C13902 | Firmware version
68
C13950 | Internal communication status
68
12.3 Table of attributes
69
Index
71
Your opinion is important to us
74
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Lenze E84DGFCA Series and is the answer not in the manual?
Ask a question
Lenze E84DGFCA Series Specifications
General
Brand
Lenze
Model
E84DGFCA Series
Category
Recording Equipment
Language
English
Related product manuals
Lenze E94AZMS Series
73 pages
Lenze EZS3 A200 Series
74 pages
Lenze Drive PLC
112 pages
Need help?
General
To Next Page
