LG V280 User Manual

16
Before Operation-DVD part
LANGUAGE
Menu Language
Select a language for the VCR and DVD’s setup menu
and information display.
Disc Audio / Subtitle / Menu
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
Original: Refers to the original language in which the
disc was recorded.
Other: To select another language, press number
buttons then ENTER/OK to enter the corresponding
4-digit number according to the language code list in
the reference chapter (see page 33). If you enter the
wrong language code, press CLEAR.
DISPLAY
TV Aspect
4:3 : Select when a standard 4:3 TV is connected.
16:9 : Select when a 16:9 wide TV is connected.
Display Mode
Display Mode setting works only when the TV Aspect
mode is set to “4:3”.
Letterbox: Displays a wide picture with bands on the
upper and lower portions of the screen.
Panscan:
Automatically displays the wide picture on the
entire screen and cuts off the portions that do not fit.
Progressive Scan
Progressive Scan Video provides the highest quality
pictures with less flickering.
If you are using the Component Video jacks for connec-
tion to a TV or monitor that is compatible with a pro-
gressive scan signal, set Progressive Scan to On.
To turn On progressive scan:
Connect component out of this unit to the input of your
monitor/television, set your television or monitor to
Component Input.
1. Select “Progressive Scan” on the DISPLAY menu
then press B.
2. Select “On” using the v / V buttons.
3. Pressing ENTER/OK will set this unit to Progressive
scan mode.
Caution:
Once the setting for progressive scan output is entered,
an image will only be visible on a progressive scan
compatible TV or monitor. If you set Progressive Scan
to On in error, you must reset the unit.
1) Remove any disc from the unit and close the disc
tray. See that “DISC” is displayed on the display
window.
2) Press STOP on the remote control and hold it for five
seconds before releasing it. The video output will be
restored to the standard setting and a picture will
once again be visible on a conventional analog TV or
monitor.
TV Output Select
Set this unit TV Output Select options according to the
TV connection type.
YPbPr: When your TV is connected with the
COMPONENT/PROGRESSIVE SCAN VIDEO OUT
jacks on this unit.
RGB: When your TV is connected with the SCART
(RGB signal) jack.
DVD
DVD
DVD
Menu Language
Original
English
Off
Original
Disc Audio
Disc Subtitle
Disc Menu
Move Select
LANGUAGE
DISPLAY
TV Aspect
Widescreen
16 : 9
Display Mode
OffProgressive Scan
Move Select
TV Output Select RGB
DISPLAY
TV Aspect
TV Output Select
Display Mode
Move Enter Prev.
OnProgressive Scan
Off

LG V280 Specifications

General

power requirements	AC 200-240V, 50/60 Hz
power consumption	17W
operating temperature	5˚C to 35˚C (41˚F to 95˚F)
operating humidity	5 % to 90 %
laser wavelength	650 nm
frequency response (DVD PCM 96 kHz)	8 Hz to 44 kHz
frequency response (DVD PCM 48 kHz)	8 Hz to 22 kHz
frequency response (CD)	8 Hz to 20 kHz
signal-to-noise ratio	More than 100dB
harmonic distortion	Less than 0.008%
dynamic range (DVD)	More than 100 dB
dynamic range (CD)	More than 95 dB
audio input (VCR SCART)	-6.0dBm, more than 10 kohms
audio input (VCR RCA)	-6.0dBm, more than 47 kohms
video input (VCR SCART/RCA)	1.0 Vp-p, 75 ohms
video output (DVD)	1 Vp-p 75 ohms, sync negative
component video output (Y)	1.0 V (p-p), 75 Ω
component video output (Pb/Pr)	0.7 V (p-p), 75 Ω
RGB output (DVD)	0.7 Vp-p, 75 ohms
audio output (coaxial audio DVD)	0.5 V (p-p), 75 Ω
audio output (analog audio DVD)	2.0 Vrms (1 KHz, 0 dB), 600 Ω
audio output (VCR SCART)	-6.0dBm, less than 1 kohms
video output (VCR SCART)	1.0Vp-p, 75 ohms
RGB output (VCR)	0.7 Vp-p, 75 ohms

Weight and Dimensions

dimensions	430 x 78.5 x 265 mm (W x H x D)
mass	4.2 kg