Makita HR4001C Technical Information

Model No.
Description
NEW TOOL
CONCEPT AND MAIN APPLICATIONS
P 1 / 20
Specification
Standard equipment
Optional accessories
Continuous Rating (W)
Voltage (V)
No load speed: min-1=rpm.
Blow per min: min-1=bpm.
Cycle (Hz)
Input Output
500
Max. Output (W)
110
120
220
230
240
12
11
6.2
6.2
6.2
50 / 60
50 / 60
50 / 60
50 / 60
50 / 60
1,100
1,100
1,100
1,100
1,100
1,500
1,500
1,200
1,200
1,500
Current (A)
Model No.
Side handle assembly (D-shaped) .......... 1 pc
Side handle (Bar-shaped) ....................... 1 pc
Depth gauge ........................................... 1 pc
Assorted T.C.T. hammer bits
Assorted Bull points
Assorted Core bits
Assorted Cold chisels
Assorted Scaling chisels
Chisel for tile removal
Grooving chisel
Clay spade
Bushing tool
Rammer
Shank for rammer and bushing tool
Chemical anchor adaptor
Bit Grease
Grease vessel
Side handle assembly (D-shaped)
Plastic Carrying Case
Blow Out Bulb
Safety Goggle
Hammer Service Kit
Bit grease ................................. 1 pc
Plastic carrying ........................ 1 pc
Cleaning cloth .......................... 1 pc
HR4001C HR4010C
6.3 (13.9)5.9 (13.0)
Europe: 4.0 (13.1); Brazil, Chile: 2.0 (6.6); Other countries: 5.0 (16.4)
HR4011C
Dimensions: mm (")
Width (W)
Height (H)
Length (L)
Model No. HR4001C HR4010C HR4011C
468(18-1/2)
116(4-9/16)106(4-3/16)
261(10-1/4)
Note: The standard equipment for the tool shown above may differ by country.
HR4001C, HR4010C, HR4011C
Rotary Hammers 40mm (1-9/16")
Bit type
Capacity: mm (")
Torque limiter
Double insulation
Net weight: kg (lbs)
Power supply cord: m (ft)
Electronic
features
Variable speed control by dial
Constant speed control
Soft start
Yes
Yes
Yes
Yes
Yes
Concrete: 40 (1-9/16)
105 (4-1/8)
235 - 480
1,350 - 2,750
Max Core bit diameter
Max bit diameter
SDS Max-drive, Shank diameter: 18mm (11/16")
These three rotary hammers have been developed to surpass
competitions in vibration level, operation efficiency and
cost-effectiveness.
Listed below are their main features.
Active dynamic vibration absorber
Model No.
Vibration absorbing handle
Selectable two on-off switches
HR4001C
Yes Yes
Yes
YesYes
No
No
HR4010C HR4011C
No
No
HR4001C
L
H
W
L
H
W
L
H
W
HR4010C
HR4011C
500
550
550
550
T
ECHNICAL INFORMATION

Makita HR4001C Specifications

General

Cord length	4 m
Input power	1100 W
Output power	1200 W
Power source	AC
Impact rate	2750 bpm
Rated speed (max)	480 RPM
Impact energy (max)	6.8 J
Sound pressure level	92 dB
Drilling diameter in concrete (max)	40 mm

Weight and Dimensions

Depth	106 mm
Width	468 mm
Height	261 mm
Weight	6300 g