Manitou MLA 628 -120 LSU 3-E2 Series User Manual

1 - 201 - 20
- Use the recommended lubricants (never use contaminated lubricants).- Use the recommended lubricants (never use contaminated lubricants).
- Do not fill the fuel tank when the I.C. engine is running.- Do not fill the fuel tank when the I.C. engine is running.
- Only fill up the fuel tank in areas specified for this purpose.- Only fill up the fuel tank in areas specified for this purpose.
- Do not fill the fuel tank to the maximum level.- Do not fill the fuel tank to the maximum level.
- Do not smoke or approach the lift truck with a flame,- Do not smoke or approach the lift truck with a flame, when the fuel tank is open or is being filled.when the fuel tank is open or is being filled.
HHYDRAULICYDRAULIC
- Any work on the load - Any work on the load handling hydraulic circuit is fohandling hydraulic circuit is forbidden except for the operarbidden except for the operations described in parttions described in part : 3 - MAINTENANCE.: 3 - MAINTENANCE.
- Do not attempt to loosen unions,- Do not attempt to loosen unions, hoses or any hydhoses or any hydraulic component with the circuit under pressure.raulic component with the circuit under pressure.
BALA
BALANCINNCING VAG VALVELVE : For inspection, see: For inspection, see : 3 – : 3 – MAINTENMAINTENANCEANCE : D - EVERY 500 : D - EVERY 500 HOURS SERVICE. It HOURS SERVICE. It is dangerous to change the setting andis dangerous to change the setting and
remove the balancing valves or safety valves which may be fitted to your lift truck cylinders. These operations must only be performed byremove the balancing valves or safety valves which may be fitted to your lift truck cylinders. These operations must only be performed by
approved personnel (consult your dealer).approved personnel (consult your dealer).
The HYDRAULIC ACCUMULATORS that may be fitted on your lift truck are pressurized units. Removing these accumulators and their pipe-The HYDRAULIC ACCUMULATORS that may be fitted on your lift truck are pressurized units. Removing these accumulators and their pipe-
work is a dangerous operation and must only be performed by approved personnel (consult your dealer).work is a dangerous operation and must only be performed by approved personnel (consult your dealer).
EE
LECTRICITYLECTRICITY
- Do not short-circuit the star- Do not short-circuit the star ter relay to start the IC engine. If the gear reverser is not in neutral and the parking brake is not enga-ter relay to start the IC engine. If the gear reverser is not in neutral and the parking brake is not enga-
ged,ged, the lift truck mathe lift truck may suddenly sy suddenly start to move.tart to move.
- Do not drop metallic items on the battery.- Do not drop metallic items on the battery.
- Disconnect the battery before working on the electrical circuit.- Disconnect the battery before working on the electrical circuit.
BALANCING VALVE : For inspection, see : 3 – MAINTENANCE : D - EVERY 500 HOURS SERVICE. It is BALANCING VALVE : For inspection, see : 3 – MAINTENANCE : D - EVERY 500 HOURS SERVICE. It is dangerous to chan-dangerous to chan-
ge the setting or remove the balancing valves or safety valves which may be fitted to your lift truck cylinders. Thesege the setting or remove the balancing valves or safety valves which may be fitted to your lift truck cylinders. These
operations must only be performed by approved personnel (consult your dealer).operations must only be performed by approved personnel (consult your dealer).
WARNINGWARNING
The HYDRAULIC ACCUMULATORS which may be fitted on The HYDRAULIC ACCUMULATORS which may be fitted on your lift truck, are under high pressure, your lift truck, are under high pressure, it is dangerous to dis-it is dangerous to dis-
mantle them. This operation must only be performed by approved personnel (consult your dealer).mantle them. This operation must only be performed by approved personnel (consult your dealer).
WARNINGWARNING

WWELDINGELDING
- Disconnect the battery before any welding operations on the lift truck.- Disconnect the battery before any welding operations on the lift truck.
- When carrying out electric welding work on the lift truck,- When carrying out electric welding work on the lift truck, connect the negative cable from the equipment connect the negative cable from the equipment directly to the part beingdirectly to the part being
welded,welded, so as to avoid high tension current passing through the alternatorso as to avoid high tension current passing through the alternator..
- Never carry out welding or work which gives off heat on an assembled tire. The heat would increase the pressure which could- Never carry out welding or work which gives off heat on an assembled tire. The heat would increase the pressure which could
cause the tire to explode.cause the tire to explode.
- If the lift truck is equipped with an electronic control unit,- If the lift truck is equipped with an electronic control unit, disconnect this before starting to weld,disconnect this before starting to weld, to avoid the risk of causto avoid the risk of causing irre-ing irre-
parable damage to electronic components.parable damage to electronic components.
WWASASHIHINGNG TTHHEE LLIIFFTT TTRRUUCCKK
- Clean the lift truck or at least the area concerned before any intervention.- Clean the lift truck or at least the area concerned before any intervention.
- Remember to - Remember to close and lock close and lock all accesses to all accesses to the lift truck (doors,the lift truck (doors, windows,windows, cowls…).cowls…).
- During washing,- During washing, avoid the articulations and electrical components avoid the articulations and electrical components and connections.and connections.
- If necessa- If necessary,ry, proteprotect against penetct against penetratioration of n of watewaterr,, steam or cleaning agensteam or cleaning agents,ts, compocomponents susnents susceptibceptible of le of being damagbeing damaged,ed, parti-parti-
cularly electrical components and connections and the injection pump.cularly electrical components and connections and the injection pump.
- Clean the lift truck of an- Clean the lift truck of any fuel,y fuel, oil or grease trace.oil or grease trace.
FOR ANY INTERVENTION OTHER THAN REGULAR MAINTENANCE,FOR ANY INTERVENTION OTHER THAN REGULAR MAINTENANCE, CONSULT YCONSULT YOUR DEALER.OUR DEALER.
CONTENTSCONTENTS
https://www.forkliftpdfmanuals.com/

Manitou MLA 628 -120 LSU 3-E2 Series Specifications

General

Brand	Manitou
Model	MLA 628 -120 LSU 3-E2 Series
Category	Forklifts
Language	English