Marantz SR6003 User Manual

61
ENGLISH
BASIC
CONNECTIONS
BASIC OPERATION
ADVANCED
CONNECTIONS
SETUP
ADVANCED
OPERATION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
ADVANCED
OPERATION
CHANNEL DIRECT CALL
You can select the desired channel by directly tapping
the numeric keypads on the remote controller.
1
.
2
.
3
.
4
.
1.
To select tuner, press the TUNE button twice
within two seconds on the remote controller.
2.
Press the BAND button to select SIRIUS
band.
3.
Press the F.DIRECT button.
“SR - - -” will appear on the display.
4.
Input the three digit number for your desired
channel with the numeric keypad on the
remote controller.
5.
The desired channel will automatically be
tuned.
Note:
•
If there is no input on the keypad for 5 sec., the input
is cancelled to return to the original display.
Notes:
•
“UPDATING” is displayed while updating channel
map.
• “SUB UPDT” is displayed while updating
subscription.
• When the selected channel is not available,
“INVALID” is dispIayed.
PRESET MEMORY
You can store the desired channel in the Preset
Memory.
(You can preset 50 SIRIUS Satellite Radio channels
in addition to FM/AM stations.)
2. 4.3.
2
.
3
.
(Using the unit)
1.
Tune into the desired channel.
2.
Press the MEMORY button on the front panel.
”- -” (preset number) starts blinking on the
dispIay.
--SR040
3.
Select the preset number by pressing the 1
or 2 cursor buttons, While this is still blinking
(approx. 5 seconds)
01SR040
4.
Press the MEMORY button again to enter.
The display stops blinking.
The channel is now stored in the specified
preset memory location.
(Using the remote controller)
1.
Tune into the desired channel.
2.
Press the MEMO button on the remote
controller. “- -” (preset number) starts blinking
on the display.
3.
Enter the desired preset number by pressing
the numeric buttons.
Note:
•
When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
CHECKING THE SIRIUS PRESET CHANNEL
The preset channel can be checked on the on screen
display.
1
.
2
.
3
.
4
.
(Using the remote controller)
1.
To select tuner, press the TUNE button twice
within two seconds on the remote controller.
2.
Press the BAND button to select SIRIUS
band.
3.
Press the INFO button. to view a list of tuner
preset channeI on the on screen display.
4.
If there are 10 or more preset channel, press
the lNFO button again.
SIRIUS PRESET LIST
NO. 1 SR010 XXXXXXXXXX
NO. 2 SR011 XXXXXXXXXX
NO. 3 SR015 XXXXXXXXXX
NO. 4 SR022 XXXXXXXXXX
NO. 5 SR125 XXXXXXXXXX
Note:
•
The preset channel indication disappears in about 5
sec.
SR6003U01ENG34.indd61SR6003U01ENG34.indd61 08.8.11:08:08PM08.8.11:08:08PM

Marantz SR6003 Specifications

General

Channels	7.1
HDMI Inputs	4
HDMI Outputs	1
Response Bandwidth	10 Hz - 100 kHz
Signal-To-Noise Ratio	105 dB
THD	0.08%
Input Impedance	47 kOhm
Input Sensitivity	200 mV
Tuner Bands	AM/FM
HDMI Switching	Yes
Frequency Response	10 Hz - 100 kHz
HDMI Pass-Through	Yes
AM/FM Tuner	Yes
Multi-room Output	Yes
Zone 2 Output	Yes
Dolby Technologies	Dolby Digital Plus, Dolby TrueHD
DTS Technologies	DTS-HD Master Audio
Video Upscaling	Up to 1080p
Network Connectivity	No
Audio D/A Converter	192kHz/24-bit
Output Impedance / Channel	8 ohms
Video Inputs	4 HDMI, 3 Component, 4 Composite
Video Outputs	1 HDMI, 1 Component, 1 Composite
Audio Inputs	Digital coaxial x 2, Digital optical x 2
Audio Outputs	Pre-out
Amplifier Output Details	110W x 7 (8 ohms, 20Hz-20kHz, 0.08% THD)
Output Power / Channel	110W (8 ohms, 20Hz-20kHz, 0.08% THD)