810762-UTG-E-1016
4 Johnson Controls Unitary Products
ACCESSORIES
Propane (LP) Conversion Kit - This accessory conversion kit
may be used to convert natural gas units for LP operation.
S1-1NP0347 - All Models except 130K Model
S1-1NP0501 - 130K Model
LP Stainless Steel Burner Kit - This accessory conversion kit
may be used to convert existing burners to stainless steel burn-
ers for LP use only.
S1-32926889000 - All LP Models
Natural (NAT) Gas Stainless Steel Burner Kit - This acces-
sory kit may be used to replace existing burners with stainless
steel burners for NAT gas use only.
S1-32924441000 - All NAT gas Models
Concentric Vent Termination - For use through rooftop, side-
wall. Allows combustion air to enter and exhaust to exit through
single common hole. Eliminates unsightly elbows for a cleaner
installation.
S1-1CT0302 (2") & S1-1CT0302-636 (2")
S1-1CT0303 (3") & S1-1CT0303-636 (3")
Sidewall Vent Termination Kit - For use on sidewall, two-pipe
installations only. Provides a more attractive termination for
locations where the terminal is visible on the side of the home.
S1-1HT0901 (3")
S1-1HT0902 (2")
Condensate Neutralizer Kit - Neutralizer cartridge has a 1/2”
plastic tube fittings for installation in the drain line. Calcium car-
bonate refill media is available from the Source 1 Parts (p/n
026-30228-000).
S1-1NK0301
Side Return Filter Racks - The S1-1SR0200 Kit accommo-
dates a 1”, 2” or 4” filter. The S1-1SR0402 Kit accommodates a
1” filter only.
S1-1SR0200 - All Models
S1-1SR0402 - All Models
Bottom Return Filter Racks - The S1-1BR05* series are gal-
vanized steel filter racks. The S1-1BR06* series are pre-painted
steel filter racks to match the appearance of the furnace cabi-
net. The S1-1BR05* and S1-1BR06* series filter racks accom-
modate a 1”, 2” or 4” filter.
S1-1BR0514 or S1-1BR0614 - For 14-1/2” cabinets
S1-1BR0517 or S1-1BR0617 - For 17-1/2” cabinets
S1-1BR0521 or S1-1BR0621 - For 21” cabinets
S1-1BR0524 or S1-1BR0624 - For 24-1/2” cabinets
Combustible Floor Base Kit - These kits are required to pre-
vent potential overheating situations when the furnaces are
installed in downflow applications directly onto combustible
flooring material. These kits are also required in any applica-
tions where the furnace is installed in a downflow configuration
without an indoor coil and where the combustible floor base kit
provides access for combustible airflow.
S1-1CB0514 - For 14-1/2” cabinets
S1-1CB0517 - For 17-1/2” cabinets
S1-1CB0521 - For 21” cabinets
S1-1CB0524 - For 24-1/2” cabinets
High Altitude Pressure Switches - For installation where the
altitude is less than 5,000 feet, it is not required that the pres-
sure switch be changed. For altitudes above 5,000 feet, see kits
below.
S1-1PS3306 - 060
S1-1PS3307 - 040, 080
S1-1PS3302 - 100, 120
Thermostats - Compatible thermostat controls are available
through accessory sourcing. For optimum performance, these
outdoor units are fully compatible with our residential touch
screen thermostat with proprietary (patent-pending) hexagon
interface. For more information, see the thermostat section of
the Product Equipment Catalog.
S1-THXU280 - All Models
To Next Page
Loading...
General