(Type FSP CATEGORY IV Direct
or Non Direct Vent Air Furnace)
Installer:
Affix all manuals
adjacent to the unit.
As a professional installer you have an obligation to know
the product better than the customer. This includes all safety
precautions and related items.
Prior to actual installation, thoroughly familiarize yourself
with this Instruction Manual. Pay special attention to all
safety warnings. Often during installation or repair it is
possible to place yourself in a position which is more
hazardous than when the unit is in operation.
Remember, it is your responsibility to install the product
safely and to know it well enough to be able to instruct a
customer in its safe use.
Safety is a matter of common sense...a matter of thinking
before acting. Most dealers have a list of specific good
safety practices...follow them.
The precautions listed in this Installation Manual are intended
as supplemental to existing practices. However, if there is
a direct conflict between existing practices and the content
of this manual, the precautions listed here take precedence.
RECOGNIZE THIS SYMBOL
AS A SAFETY PRECAUTION.
*NOTE: Please contact your distributor or our website for
the applicable Specification Sheet referred to in this manual.
I
NSTALLATION
I
NSTRUCTIONS
FOR
*CVC96 & *MVC96
T
WO
-S
TAGE
G
AS
F
URNACE
These furnaces comply with requirements em-
bodied in the American National Standard / Na-
tional Standard of Canada ANSI Z21.47·CSA-2.3
Gas Fired Central Furnaces.
is a registered trademark of Maytag Corporation or its related companies and is used under license. All rights reserved.
IOG-2008D
10/15
5151 San Felipe Suite 500
Houston, TX 77056
www.goodmanmfg.com • www.amana-hac.com
© 2014-2015 Goodman Manufacturing Company, L.P.
TABLE OF CONTENTS
SAFETY CONSIDERATIONS.................................... 3
SHIPPING INSPECTION .......................................... 4
ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS .................. 4
TO THE INSTALLER ........................................... 5
PRODUCT DESCRIPTION ....................................... 5
FEATURES .................................................... 5
PRODUCT APPLICATION ....................................... 5
LOCATION REQUIREMENTS & CONSIDERATIONS ........... 6
CLEARANCES AND A CCESSIBILITY ................................. 8
EXISTING FURNACE REMOVAL ................................... 8
THERMOSTAT LOCATION ........................................ 9
COMBUSTION & VENTILATION AIR REQUIREMENTS........ 9
INSTALLATION POSITIONS ...................................10
HORIZONTAL APPLICATIONS & CONSIDERATIONS ........10
FURNACE SUSPENSION ........................................10
FRONT COVER PRESSURE SWITCH TUBE LOCATION ...............10
DRAIN TRAP AND LINES ......................................10
LEVELING ...................................................10
ALTERNATE VENT/FLUE AND COMBUSTION A IR CONNECTIONS .....10
ALTERNATE ELECTRICAL AND GAS LINE CONNECTIONS ............11
DRAIN PAN ..................................................11
FREEZE PROTECTION .........................................11
PROPANE GAS/HIGH ALTITUDE INSTALLATIONS ..........11
VENT/FLUE PIPE & COMBUSTION AIR PIPE ................12
DUAL CERTIFICATION: NON-DIRECT/DIRECT VENT ...............12
MATERIALS AND JOINING METHODS .............................12
PROPER VENT/FLUE AND COMBUSTION A IR PIPING PRACTICES .....13
TERMINATION LOCATIONS ......................................13
CANADIAN VENTING REQUIREMENTS ............................14
STANDARD FURNACE CONNECTIONS .............................14
VENT/FLUE PIPE ............................................14
COMBUSTION A IR PIPE ........................................14
NON-DIRECT VENT INSTALLATIONS .............................15
NON-DIRECT VENT (SINGLE PIPE) PIPING ......................16
VENT/FLUE PIPE TERMINATIONS...............................16
VENT & COMBUSTION AIR INTAKE MEASUREMENTS FOR
STANDARD HORIZONTAL TERMINATIONS (DUAL PIPE) ..........18
VENT/INTAKE TERMINATIONS FOR INSTALLATION OF MULTIPLE
DIRECT VENT FURNACES ...................................19
CONCENTRIC VENT TERMINATION ...............................19
SIDE WALL VENT KIT ........................................19
CONDENSATE DRAIN LINES & DRAIN TRAP ................19
GENERAL DRAIN INFORMATION .................................19
FIELD SUPPLIED DRAIN .......................................19
UPFLOW MODEL INSTALLED VERTICALLY ........................20
DRAIN EXITING RIGHT SIDE ...................................20
To Next Page
Need help?
General
