Miele WTZH 730 WPM Quick Start Guide

Applications Operation
Separate washing Changing the programme sequence
OPERATION
SEPARATE WASHING
SEPARATE DRYING
Separate drying
WTZH 730 WPM en - AU, NZ M.-Nr. 10 868 090/00
Interrupting a programme
ĺ Switch the washer-dryer off with the
button.
ĺ To continue the programme, switch the
washer-dryer back on with the button.
ɉDo not switch the washer-dryer off
before the end of a drying programme. If
this is done, all items must be removed
immediately and spread out to cool down.
ɉBefore using the washer-dryer for
the first time, ensure that it is correctly
installed and connected. Install and
connect the appliance as described in the
operating instructions.
It is essential to read the separate
operating instructions.
You can use this washer-dryer to:
– wash separately
with a maximum load of 8.0kg,
– dry separately
with a maximum load of 5.0kg,
or
– wash and dry in a continuous
sequence
with a maximum load of 5.0kg.
1 Display with sensors
See points 11 to 16 for more
information.
2 Start/Stop button
For starting the programme selected
and cancelling a programme once it has
started.
3 Temperature button
For selecting a wash temperature.
4 Spin speed button
For selecting the spin speed.
5 Drying level button
For selecting the drying level.
6 Dispensing buttons
For selecting automatic detergent
dispensing and CapDosing.
7 Options buttons
Various options can be added to the
programmes.
8 Programme selector
For selecting washing and drying
programmes.
9 Optical interface
For service technicians.
10 button
For switching the washer-dryer on and
off.
11  sensor
Scrolls down the list to the next option
or decreases a value.
12 OK sensor
Confirms the programme selected, a
value set or opens a sub-menu.
13  sensor
Scrolls up the list to the next option or
increases a value.
14 Washing sensor
For selecting the washing function.
15 Drying sensor
For selecting the drying function.
16 Delay start sensor
For selecting Delay start.
Environmentally friendly washing and drying
– Load the maximum amount for the
programme you are using.
– When smaller amounts of laundry are
washed, the Auto load control system
will reduce the amount of water and
energy used.
– Use the Express programme for small,
lightly soiled loads.
– Modern detergents make it possible
to wash at lower temperatures (e.g.
20°C). Using lower temperature
settings will save energy.
– For precise dispensing, use automatic
detergent dispensing.
– Selecting the highest possible spin
speed for the wash programme will
save energy when drying in a tumble
dryer afterwards.
2. Selecting a programme
Switching the washer-dryer on
ĺ Press the  button.
Selecting a programme via the programme selector
ĺ Turn the programme selector to the required
programme.
The maximum load for the wash programme selected will
appear in the display. This will then be replaced by the
standard display.
Selecting a programme via “Further programmes”
ĺ Turn the programme selector to Further programmes.
ĺ Touch the  or sensor until the programme you want
appears in the display.
ĺ Confirm the programme with the OK sensor.
The maximum load for the wash programme selected will
appear in the display. This will then be replaced by the
standard display.
3. Loading the drum
Opening the door
ĺ Reach under the door grip and pull the door open.
The load display will appear.
ĺ Unfold the laundry and load loosely in the drum.
ĺ Pay attention to the load indication.
Closing the door
ĺ Make sure that no items are caught between the door
and the seal.
ĺ Shut the door with a gentle swing.
The display will ask you to enter the degree of soiling of
the laundry.
3 5
1
2
4
1 Detergent dispenser drawer
2 Control panel
3 Access to filters, pumps and
emergency release
4 Door
5 Access panel for TwinDos
containers
4. Selecting programme settings
Selecting the degree of soiling
ĺ Select the degree of soiling with the or sensor and
confirm with OK.
The dosage display will appear.
Confirming the detergent dosage display
ĺ Confirm with OK.
Selecting the temperature
ĺ Press the Temperature button.
ĺ Set the temperature you want with the  and 
sensors and confirm your selection with the OK sensor.
Selecting the spin speed
ĺ Press the Spin speed button.
ĺ Set the spin speed you want with the  and  sensors
and confirm your selection with the OK sensor.
Selecting options
ĺ Use the ProgrammeManager, Stains or Further options
buttons for selecting the options you want.
Selecting Delay start
ĺ Select a Delay start time if required.
5. Adding detergent
Detergent can be dispensed via TwinDos, via the
detergent dispenser drawer or with Caps.
TwinDos
The optimum amount of UltraPhase1 and UltraPhase2
will be dispensed automatically according to the colour
mix of the load.
ĺ Press the TwinDos button.
Detergent dispenser drawer
ĺ Pull out the detergent drawer and add detergent to the
compartments ,  or .
CapDosing
There are different types of capsules available.
Each capsule contains the correct amount of detergent for
one wash cycle.
ĺ Press the Cap button, select the type of capsule
and place a capsule in the compartment.
6. Starting the programme
ĺ Press the flashing Start/Stop button.
The door will lock and the programme will
start.
The programme status will appear in the
display.
7. At the end of the programme
The door remains locked during the anti-
crease phase.
ĺ Press the Start/Stop button.
ĺ Pull open the door.
ĺ Remove the laundry.
ɉCheck that all items have been
removed from the drum.
ĺ Check the folds in the door seal for any
small articles, e.g. buttons, which might
be lodged there.
Note: For safety reasons, close the door.
ĺ Switch the washer-dryer off with the
button.
ĺ Remove any used capsules from the
detergent dispenser drawer.
Leave the detergent dispenser drawer
slightly open to allow it to dry.
See the section “After each washing
or drying programme” in the chapter
“Washing and drying in a continuous
sequence”.
2. Selecting a programme
Switching the washer-dryer on
ĺ Press the  button.
Selecting a programme via the
programme selector
ĺ Turn the programme selector to the
required programme.
Selecting a programme via “Further
programmes“
ĺ Turn the programme selector to Further
programmes.
ĺ Touch the  or sensor until the
programme you want appears in the
display.
ĺ Confirm with OK.
The maximum load for the wash
programme selected will appear in the
display. This will then be replaced by the
standard display.
1. Preparing the laundry
ĺ Empty all pockets.
ɉForeign objects (e.g. nails,
coins, paper clips etc.) can
cause damage to fabrics and to
components in the machine.
ĺ Sort the laundry by colour and by care label. Most
garments have a textile care label in the collar or side
seam.
ĺ Pre-treat stains and badly soiled areas (see the booklet
“Miele's guide to laundry care”).
3. Loading the drum
Opening the door
ĺ Reach under the door grip and pull the
door open.
ĺ Load the laundry loosely in the drum.
Do not overload the drum. Overloading
can cause unnecessary wear and tear of
the laundry, give a disappointing drying
result and cause more creasing.
ĺ Remove foreign objects like detergent
dispensing devices from the laundry.
ɉThey can melt and damage the dryer
and the laundry.
Closing the door
ĺ Shut the door with a gentle swing.
ĺ Make sure that no items are caught
between the door and the seal.
4. Selecting programme settings
Selecting the drying level
ĺ Press the Drying level button.
Select the drying level or duration you want
with the and  sensors and confirm your
selection with OK.
5. Starting the programme
ĺ Press the flashing Start/Stop button.
The door will lock and the drying
programme will start.
The programme status will appear in the
display.
The mains water tap must be kept open
for drying.
6. At the end of the programme
The door remains locked during the anti-
crease phase.
ĺ Press the Start/Stop button.
The door will be unlocked.
If you have unloaded the drum during the
anti-crease phase, make sure you spread
out the laundry to cool it down.
ĺ Pull open the door.
ĺ Remove the laundry.
See the section “After each washing
or drying programme” in the chapter
“Washing and drying in a continuous
sequence”.
ĺ Switch the washer-dryer off.
Cancelling a programme
ĺ Press the Start/Stop button and select
Cancel programme.
ĺ Touch the OK sensor.
The suds will be drained away or the
laundry will be cooled down before the door
can be opened.
Removing the laundry
ĺ Pull the door open and unload the drum.
Selecting another programme
ĺ Close the door.
ĺ Select the required programme.
ĺ Press the Start/Stop button.
Changing
Changing a programme
– after the programme has started is not
possible.
Changing the temperature
– is possible up to 5minutes after the
programme has started (not with the
Cottons programme).
ĺ Press the Temperature button.
ĺ Change the temperature using the  or
 sensors and confirm your choice with
OK.
DRYING
If you have washed a full load of laundry
and you wish to dry the laundry in the
washer-dryer afterwards, you will have
to remove half the load and carry out the
drying process in two loads.
1. Preparing the laundry
ĺ Sort the laundry according to the type
of fibre and weave, garment care label
symbol and the drying level required.
ĺ Before drying, check the drying symbol
on the care label.
Selecting drying
ĺ Touch theWashing and Drying sensors
until just theDrying indicator light remains
on.
The Washing indicator light must not be
lit up as this would mean that the relevant
wash programme would begin before the
drying process.
Selecting thermospin
ĺ Press the Spin speed button.
ĺ Set the spin speed you want with the 
and  sensors and confirm your selection
with OK.
Selecting options
ĺ Select the option you want using either
the ProgrammeManager or Further
options button.
Selecting Delay start
ĺ Select a Delay start time if required.
Changing the spin speed
– is possible up to the start of the spin
cycle.
ĺ Press the Spin speed button and change
the spin speed.
Changing the drying level / drying
duration
– is possible while a wash programme is
running.
ĺ Press the Drying level button and change
the drying level.
Selecting or deselecting drying
– is possible while a wash programme is
running.
ĺ Touch the Drying sensor.
Changing options
– Some options can be selected or
deselected after a programme has
started.
Changes cannot be made while the safety
lock is active.
Adding or removing laundry
You can add or remove items during the
first few minutes after the programme has
started.
ĺ Press the Start/Stop button.
ĺ Select Add laundry using the  or 
sensor.
If this message does not appear in the
display, then it is no longer possible to
add or remove items of laundry.
ĺ Confirm with OK.
The programme will stop and the door will
unlock.
ĺ Pull open the door and add or remove
items.
ĺ Close the door.
ĺ Press the Start/Stop button.
ĺ The programme will continue.

Miele WTZH 730 WPM Specifications

General

Current	10 A
Connected load	2400 W
AC input voltage	220-240 V
AC input frequency	50 Hz
Water consumption per cycle	105 L
Water consumption washing per cycle	- L
Energy consumption washing per cycle	5.36 kWh
Door hinge	Right
Control type	Buttons, Rotary
Display type	LED
Loading type	Front-load
Product color	White
Built-in display	Yes
Appliance placement	Freestanding
Half-load	-
Drum capacity	8 kg
Drying system	Steam
Drying capacity	5 kg
Maximum spin speed	1600 RPM
Noise level (spin)	72 dB
Noise level (wash)	46 dB
Noise level (drying)	58 dB
Cord length	2 m
Annual water consumption washing	11400 L
Annual energy consumption washing	220 kWh
Annual water consumption washing & drying	21000 L
Annual energy consumption washing & drying	1072 kWh

Weight and Dimensions

Depth	714 mm
Width	596 mm
Height	850 mm
Weight	102000 g
Depth with door open	1132 mm