Fold
Fold
Fold
Fold
Fold
Fold
Fold
Fold
Fold
Fold
Fold
Fold
Fold
Fold
OVERVIEW
The Shaw Direct IRC600 IR/UHF
Remote Controls by Universal
Electronics are our latest genera-
tion universal remote controls.
Their sophisticated technology
allows you to consolidate up to
five of your original home enter-
tainment remote controls into one
easy-to-use product.
The remote control requires
installing two (2) new AA batter-
ies (included) and simple pro-
gramming instructions to control
your TV. For best results, please
read and perform all instructions
listed here. Also, keep this guide
for future reference.
INSTALLING BATTERIES
1. Pull back the remote control’s
battery cover and remove it.
2. Insert the two (2) supplied
AA batteries according to the
+ and
-
marks in the battery
case.
3. Push the battery cover back
into place.
4. Test the unit by pressing the
power key.
If batteries are inserted cor-
rectly, the Red Light will blink.
NOTE: When batteries need replace-
ment, the remote control will stop
operating. Replace the old batteries
replace old batteries with new AA
batteries.
PROGRAMMING SAT CONTROL
Your remote control address is set at
the factory to 01869 to control all of
the functions on your Motorola satellite
receiver. However, if you have more
than one satellite receiver, you may
want to prevent the remote control in
one room from affecting the satellite
receiver in another room. To prevent
this kind of interference, you must
“pair” each remote control with each
receiver by assigning a new “address”
to each combination. This “address”
assignment is made using your remote
control as follows:
1.
Press the SAT button to select
the remote control's SAT mode.
2. Press the Options button to
display the Options screen on
your TV.
3. On the System Setting
/ Setup screen, use the
buttons to highlight the
Change System Setting /
System Setup option, then
press Enter/OK.
4. On the Systems Setting
/ Setup screen, use the
buttons to highlight the
Change Installation Setting
/ System Settings (applies to
DSR 5xx, 207, 317 receivers)
option than press Enter/OK.
5 On the System Settings
(applies to DSR 5xx, 207, 317
receivers) screen, use the
buttons to highlight
the Installation Settings
option, the press ENTER/OK.
6. On the Installation Settings
screen and use the
buttons to highlight the
Remote Control Address
option, then press ENTER/OK.
7. Once you are on the Remote
Control Address screen, dis-
regard the instructions on
screen and follow the steps
using the remote control
Keypad...
8.
Press and hold the SAT key
until the red lights flash twice
and release the SAT key.
9. Enter in the new 5 Digit SAT
address from the below list.
10. Press the Enter button to set
the same address in your
Satellite receiver. The new
address will be displayed
in the upper right corner of
your TV screen.
11. Exit from the Remote Control
Address screen.
PROGRAMMING DEVICE CONTROL
The Shaw Direct IRC 600 IR/UHF
Remote Controls are preprogrammed
to operate a Motorola satellite receiver,
a Sony TV, and Sony DVD player, than
the default brands, perform the follow-
ing steps; otherwise skip this section.
1.
Turn on the TV.
NOTE: Please read steps 2 to 4
completely before proceeding.
Highlight or write down the codes
and device you wish to program
before moving on to step 2.
2. Press and hold
Device key (TV or
AUX)
until the
Red Lights
blinks
twice, then release
TV
.
3. Locate the code for your device
in
Manufacturer’s Codes
on the
back of this user guide. Brands
are listed in alphabetical order
with the most popular codes
listed first.
4. Enter the first five-digit code for
your TV. If you perform this pro-
cedure correctly, the
Red Light
will blink twice.
NOTE: If you enter an invalid code,
the red light will display not blink
when entering the last digit and
exit the programming mode.
Repeat steps 2 to 4 with a valid
code.
5. Aim the remote control at your
TV and press
Power
once. The
device should turn off. If it does
not respond, repeat steps 2 to 4,
trying each code listed for your
brand until you find one that
works. If it still does not work, try
Searching For Your Code.
6. The TV code will be stored in the
Digital Adapter and will be repro-
grammed when the batteries are
changed and the Digital Adapter
remote is successfully re-paired
with the Digital Adapter.
TV Code:
AUX Code:
TV Code:
SEARCHING FOR YOUR CODE
If your brand of Device does not
respond to the remote control after
trying all of the codes listed, or if your
brand is not listed at all, try searching
for your code.
1. Turn on your Device.
2. Press and hold
Device key (TV or
AUX)
until the
Red Lights
blinks
twice, then release
TV
.
3. Enter in
9
-
9
-
1
. The
Red Light
will blink twice.
4. While pointing the remote
control at the Device, press and
release the CH + key until the
Device turns off. (Note: You may
need to press [CH+] numerous
times).
NOTE: In the search mode, the
remote control will send IR codes
from its library to the library of
IR codes
5. Press
Device key
once to lock in
the code. The
Red Light
will blink
twice.
CHECKING THE CODES
If you have set up the remote control
using the
Searching For Your Code
procedure, you may need to find out
which five-digit code is operating your
TV. Perform the following steps after
setting up your TV to find out which
five-digit code operates your TV.
1. Press and hold
TV
until the
Red
Light
blinks twice, then release
SET
.
2. Enter in
9
-
9
-
0
. The
Red Light
will blink twice.
3. To view the code for the first
digit, press
1
once. Wait 3 sec-
onds and count the number of
times the
Red Light
blinks (e.g.,
3 blinks =3) and write down the
number in the left most TV Code
box (at end of this section).
NOTE: If a code digit is “0”, the
red light will not blink.
4. Repeat step 3 four more times for
the remaining digits. Use
2
for the
second digit, 3 for the third digit,
4 for the fourth digit and 5 for the
fifth digit. Finish writing down the
code in the TV Code boxes (at end
of this section).
CHANGING VOLUME CONTROL
Volume Lock allows you to control the
volume through the device identified
as having your primary speaker(s),
regardless of which mode you are
using. On the Shaw Direct IRC600 IR/
UHF Remote Controls, Global Volume
Lock is set to TV, so you can control
TV volume while in the AUX, or SAT
mode. You can perform Individual
Volume Unlock on a selected device to
set its volume control for independent
operation.
Locking Volume to a Specific Mode.
1. Press and hold
SAT
until the
Red
Lights
blinks twice, then release
SAT
.
2. Enter in
9
-
9
-
3 (The Red Light will
blink twice after the 3).
3. Press and release the Mode Key
(e.g. TV) to lock Volume to.
Unlocking Volume from a specific
Mode.
1. Press and hold
Mode key to be
unlocked (e.g. AUX)
until the
Red
Lights
blinks twice, then release
SAT
.
2. Enter in
9
-
9
-
3 (The Red Light will
blink twice after the 3).
3. Press and release the Volume
Down Key the Red light will flash
4 times
USING THE MASTER POWER KEY
The Shaw Direct IRC600 IR/UHF
Remote Controls have a unique fea-
ture that allows you to sequentially
turn up to five of your home entertain-
ment devices on or off with a single
key press.
NOTE: The MASTER POWER (Power)
default setting is the SAT mode.
If it is not programmed only the
Satellite receiver and TV will turn
on or off. In the AUX or TV mode,
pressing the Power key will only
turn on or off the selected device.
Programming the Master Power Key
1. Press and hold
SAT
until the
Red
Light
blinks twice, then release
SET
.
2. Enter in
9
-
9
-
5
The
Red Light
will blink twice.
3. Press and release each mode key
once in the order that you them
in the Master Power sequence.
4. Press and release the Power key
(The red light under SAT will flash
twice).
Using the Master Power Key
After Programming, point the remote
control at your devices and press
and hold the POWER key in for 1.5
seconds
Programming the Master Power Key
1. Press and hold
SAT
until the
Red
Light
blinks twice, then release
SET
.
2. Enter in
9
-
9
-
5
The
Red Light
will blink twice.
3. Press and release the Power key
(The red light under SAT will flash
twice).
TROUBLESHOOTING
PROBLEM: The remote has stopped
controlling the Digital
Adapter.
SOLUTION: Retry the Manual Pairing
operation.
PROBLEM: During programming,
the Red Light displays
one long blink.
SOLUTION: An invalid entry has
occurred. Check the key
to be entered and try
programming again.
PROBLEM: When using the volume
lock sequence or code
verification, the Red
Light displays one long
blink.
SOLUTION: The long blink indicates
that a valid TV code has
not been programmed.
SETUP CODES FOR AMPLIFIERS
Anthem 32220
Cary Audio Design 31879
Denon 32134
Elan 30647
Flextronics 31879
Halcro 31934
Harman/Kardon 30892
Krell 31837, 32463
Left Coast 30892
Lexicon 31802
Marantz 30892, 31892, 32138
Mark Levinson 32405
Optimus 30823
Parasound 31934
Philips 30892
Pioneer 30823
Polk Audio 30892, 32242
Primare 31851
RCA 30823
Thule Audio 31851
SETUP CODES FOR TUNERS
Aiwa 31405, 30189, 31388, 31641
Akai 31512
Alco 31390
Altec Lansing 32595, 32596
AMC 31077
Amphion Media 31563
AMW 31563
Anam 31609
Apex Digital 31257, 31430, 31774
Arcam 31189, 30189
Audiotronic 31189
Audiovox 31390
B & K 30820
Bose 31229, 30639, 31629, 31841,
31933
Boston Acoustics 32162
Cambridge Sound 31370
Carver 31189, 30189
Coby 31389
Curtis 31389
Daewoo 31250
Denon 31360, 32279, 32857
Fisher 31801
Gateway 31517
Harman/Kardon 30189, 31304, 31306, 32241,
32443
Hitachi 31273, 31801
iHome 32435
iLive 32013
Insignia 31030, 31077, 31751, 31893,
32126, 32169, 32175, 32472,
32474
Integra 31298, 31320, 31805
iSymphony 32018, 32258, 32442
JBL 31306
JVC 31374, 31495, 32040, 32161,
32239, 32331
Kenwood 31313, 31570, 31569
KLH 31390, 31428
Koss 31366, 31497
LG 31293, 32197, 32284
Linn 30189
Liquid Video 31497
Magnavox 31189, 31269, 30189, 31514
Marantz 31189, 31269, 30189, 31289,
32114
McIntosh 31289
Micromega 31189
Mitsubishi 31393
Myryad 31189
Nakamichi 31313
NexxTech 31751
Norcent 31389, 31751
Nova 31389
Onkyo 30842, 31298, 31320, 31531,
31805, 32451
Optimus 31023
Oritron 31366, 31497
Panasonic 31308, 31518, 31275, 31288,
31316, 31548, 31633, 31763,
31764, 32221, 32452, 32967
Philco 31838
Philips 31189, 31269, 30189, 31266,
32311, 32459
Pioneer 31023, 31384, 31935
Polaroid 31508
Polk Audio 30189, 31289, 32244, 32270
Proscan 31254
RCA 31023, 31609, 31254, 31390,
31511, 32041
Rio 31869
Samsung 31295, 31304, 31500, 31868
Sansui 30189
Sanyo 31469, 31801
Sherwood 31077, 31517, 31653, 31905,
32169
Sherwood New 32169
Sonic Blue 31869
Sony 31759, 31058, 31441, 31258,
31622, 31558, 31658, 31758,
31822, 31858, 32172, 32216,
32320, 32475, 32522
Stereophonics 31023
Sunfire 31313
Teac 31390, 31528
Technics 31308, 31518, 31633
Thorens 31189
Toshiba 31788
Venturer 31390
Vizio 31517
Wards 30189
Yamaha 30176, 30376, 31176, 31276,
31331, 31375, 31376, 31476,
31815, 32061, 32455, 32467,
32471
Zenith 31293
SETUP CODES FOR DIGITAL MEDIA
Apple 31115
B & W 32441
Denon 32502
HTI 32439
Vizio 32454
Yamaha 31797, 32021, 32458
ZVOX 32332, 32334
SETUP CODES FOR TELEVISION
Accurian 11803
Action 10873
Admiral 10463
Advent 10761, 10783, 10815, 10817,
10842
Akai 10812, 11675, 10702, 10030,
10672, 11676, 11935, 12232
Albatron 10700, 10843
Ampro 10751
AOC 10030, 11365, 11589, 11590,
12014, 12087, 12402, 12479
Aomni 11623
Apex Digital 10748, 10879, 10765, 10767,
10890, 11217, 12397
Astar 11531, 11738
Audiovox 10451, 10623, 10802, 10846,
10875, 11937, 11951, 11952
Aventura 10171
Axion 11937
Bell & Howell 10154
BenQ 11032, 11212, 11315
Boxlight 10893
Broksonic 10463, 11905, 11929, 11935,
11938
Byd:sign 11309
C & M 10700
Candle 10030
Carnivale 10030
Carver 10054
CCE 10623
Celebrity 10000
Celera 10765
Changhong 10765
Citizen 10060, 10030, 11669, 11671,
11672, 11928, 11935
Coby 11634, 12306, 12314, 12315
12326, 12338, 12340, 12343
12344, 12345, 12347, 12348
12350, 12351, 12560
Commercial Solutio 11447, 10047
Crosley 10000, 10054
CTX 10700
Curtis 11326, 12352, 12466
Cytron 11326
Daewoo 10154, 10451, 11661,10623,
10661, 10672, 11928
Dell 11264, 11080, 11178, 11403,
11863
Denon 10145
Diamond Vision 11996
Digital Lifestyles 11765
Digital Projection 11750
DirecTV 11501
Disney 11665, 12152
Dream Vision 11164
Dumont 10017
Durabrand 10463, 10178, 10171, 11034,
11665
Dwin 10720, 10774
Dynex 11463, 11780, 11785, 11810,
12049, 12184
Electroband 10000
Electrograph 11755, 11623
Electrohome 10463, 11670, 11672
Element 11687, 12183
Emerson 11864, 10154, 10451, 10463,
10178, 10171, 11661, 10623,
11394, 11665, 11905, 11928,
11929, 11944, 11963
Emprex 11422, 11765
Envision 10030, 10813, 11365, 11589,
12014, 12087
Epson 10833, 10840, 11290
ESA 10812, 10171, 11944, 11963
Fisher 10154
Fujitsu 10809, 10683, 10853
Funai 10000, 10171, 11271, 11904,
11963, 11979
Gateway 11755, 11756
GE 11447, 10047, 10051, 10451,
10178, 11347, 11922, 12359
GFM 10171, 11665, 11963, 12167
Gibralter 10017, 10030
Go Video 10886, 11823
GoldStar 10178, 10030, 11926
Grundig 10683
Haier 11034, 11749, 12309
Hallmark 10178
Hanns.G 11783
Hannspree 11348, 11351, 11745, 11783
Harley Davidson 11904
Harman/Kardon 10054
Helios 10865
Hello Kitty 10451
Hewlett Packard 11494
Hisense 10748, 11314, 11660, 12098,
12355, 12419
Hitachi 11643, 11145, 10145, 11345,
11904
HP 11494
Humax 11501
Hyundai 10849, 11219, 11294
iLo 11286, 11603, 11665, 11684,
11990
Infinity 10054
InFocus 11164, 12199
Fold
SHAW DIRECT IRC600 IR/
UHF Remote Control
To Next Page
Need help?
General
