1. OPERATION (FOR PROGRAMMING, PROCEED TO STEP 2)
This MMK200 Digital Keypad is designed for use with Mighty Mule automatic gate operators. The radio format provides unparalleled
security with more than a million different codes.
To activate the automatic gate operator, the user enters their unique 1 to 6 digit long code on the unit’s keypad and presses the (
) button.
For up to 30 seconds after the last activation, the keypad can be re-triggered by simply pressing the (
) button again. This allows the user to
stop or reverse the opener quickly, without having to re-enter their code.
The keypad has built-in lighting for use at night or in dark areas. The clear silicone keys are backlit with a pleasing blue glow. Pressing any
key will activate the backlight.
The Mighty Mule gate operator contains a built-in receiver that is
programmed by sending a signal from the keypad. This stores the keypad’s
code into the receiver’s memory. The receiver will retain its memory even
without power and will only activate from the “memorized” keypad.
MMK200
Digital Keypad
for Automatic
Gate Operators
2. PROGRAM A KEYPAD CODE TO THE OPENER (MODELS MM371, MM372, MM571, MM572)
On the control board, press and hold the S3 button ( ) until LED2 [beside the S3 button] illuminates and the buzzer sounds. Release
the (S3) button (
).
While the LED2 button is lit, enter a 1-6 digit code into the keypad. Then PRESS and HOLD the keypad’s
key until the opener
BEEPS and the light BLINKS once. Repeat Steps 1 & 2 for any additional keypad codes.
DELETE A KEYPAD CODE: Follow Steps 1 and 2 (above) to delete (overwrite) an existing keypad code.
10021997 Rev-D
REMOVE THE BATTERY ASSEMBLY
TO ACCESS THE SECOND MOUNTING
HOLE (SEE CHANGING BATTERIES,
BELOW).
ALIGN THE SCREW WITH THE
MOUNTING HOLE AND TIGHTEN.
REPLACE THE BATTERY ASSEMBLY.
DRIVE THE PROVIDED SCREW
INTO THE MOUNTING SURFACE
(NOT ALL THE WAY).
ALIGN THE SCREW WITH U-SHAPED
SLOT ON THE BACK OF THE UNIT,
INSERT AND SLIDE DOWNWARD
UNTIL SECURE.
ADJUST THE SCREW DEPTH IF
NEEDED.
USE THE ANCHOR
SUPPLIED IF REQUIRED
USE THE ANCHOR
SUPPLIED IF REQUIRED
WALL MOUNTING
INSTALL 3 FRESH AAA BATTERIES
INTO THE CRADLE.
REPLACE BATTERY CRADLE AND
SECURE THE SCREW.
REMOVE ONE SCREW THEN REMOVE
THE BATTERY CRADLE.
REMOVE THE OLD BATTERIES FROM
THE CRADLE, AND DISPOSE OF THEM
PROPERLY.
CHANGING BATTERIES
KEYPAD OPERATION
MIGHTY MULE LIMITED WARRANTY
This product is warranted to the original consumer (“You”) by Nice North
America against defects in material and workmanship for a period of
twelve (12) months from the date of purchase. This limited warranty
only extends to you if the item was purchased directly from Nice North
America or through an authorized sales partner. Nice North America
will, at its option, either repair or replace any product that it conrms is
defective and eligible for service under this warranty and will return the
repaired or replaced product to you at Nice North America’s cost. This
warranty does not apply to damage to the product from negligence,
abuse, abnormal usage, misuse, accidents, acts of god, normal wear
and tear, failure to follow the manufacturer’s instructions, or arising from
improper installation, storage or maintenance. Some states do not allow
the exclusion or limitation of incidental and consequential damages,
so the above limitation or exclusion may not apply. This warranty gives
you specic legal rights and you may also have other rights, which vary
from state to state. In order to be protected by this warranty, a copy of
the receipt or other valid proof of purchase must be provided with any
product that is being repaired or replaced under this warranty. In order to
initiate warranty service for your product, please contact Tech Services
at (800) 421-1587 for a Return Authorization Number (“RA”) and other
important details.
DAYTIME OPERATION
PRESS THE LIGHT ( ) BUTTON (TO LIGHT KEYPAD)
NIGHTTIME OPERATION
1-6 DIGIT KEYPAD CODE THAT
WAS PROGRAMMED INTO THE OPENER
ENTER THE KEYPAD CODE
PRESS
ENTER THE KEYPAD CODE
PRESS
1-6 DIGIT KEYPAD CODE THAT
WAS PROGRAMMED INTO THE OPENER
WARNING: Changes, modications or adjustments not expressly approved
by Nice North America could void the user’s authority to operate this
equipment. There Are No User Serviceable Parts.
NOTICE: This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This device complies with Industry Canada License-exempt RSS standards.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
DELETING A KEYPAD CODE (MM271 OR MM272)
Follow Steps 1 through 5 to delete the keypad code.
Note: If using the MM271, the gate must be in the closed position to delete an existing keypad code. It can be open or closed to program a
new code.
SCREW ANCHORS
MOUNTING SCREWS
KEYPAD
PACKAGE INCLUDES
3 AAA batteries included.
WARNING
KEEP BATTERIES OUT REACH OF CHILDREN. Swallowing batteries can
lead to serious injury or death. If you suspect someone has swallowed a
battery, go to the hospital immediately. Do not induce vomiting or eat or
drink anything.
For more information, call the National Battery Ingestion Hotline: 202-
625-3333.
The battery identication number for this product is AAA Alkaline (LR03).
SOFT BLUE LIGHTS
ILLUMINATE THE KEYS
FOR NIGHTTIME USE.
THE KEY STAYS ACTIVE FOR 30 SECONDS
AFTER A CODE IS USED SO THE OPENER
CAN BE STOPPED OR REVERSED.
TEN KEYS FOR ENTERING
1-6 DIGIT KEYPAD CODES
USING NUMBERS OR LETTERS.
KEY FEATURES
Compatible with Mighty Mule
automatic gate operators:
271, 272, 371W, 372W, 571W
and 572W
Installation Instructions
PROGRAMMING A KEYPAD CODE (MM271 OR MM272)
1. Use the ON/OFF switch on the opener control box to
power the system off.
2. Enter the desired 1-6 digit code into the keypad.
PRESS and HOLD the
key, and continue to hold
until instructed to release.
3. While still holding the
key, use the ON/OFF switch
on the control box to power the system ON.
4. After the startup beep, there will be a silence for 5-10
seconds, followed by an uninterrupted beep.
5. Release the
key after the beep.
UP
DOWN
Press the
S3 button ( )
Mighty Mule Technical Service: 800-421-1587
For more information about the full line of Mighty Mule
Automatic Gate Operators, Gate Openers and Access
Controls visit.
www.mightymule.com
Niceforyou.com
©2024 Nice North America LLC.
Mighty Mule is a registered trademark of Nice North America LLC.
All rights reserved.
To Next Page
Need help?
General
