8 – English
EN
Durability is the average economic life of the product. The value of durability is
strongly influenced by the demand index of the manoeuvres performed by the
automatism: that is the sum of all the factors which contribute to the wear of
the product (see Table 2).
To establish the probable durability of your automatism proceed as follows:
01. Calculate the demand index
summing the values in percentage of the
entries present in Table 2 to each other.
Example:
- leaf weight = 200 Kg (demand index = 20%)
- leaf length = 1,5 m (demand index = 20%)
- no other stress elements present
Total demand index
= 40%
02. In Graph A, from the value just found, trace a vertical line until you intersect
the curve; from this point trace a horizontal line to cross the line of “cycles
of manoeuvres”. The value established is the estimated durability of your
product.
Example:
Total demand index
= 40% ––> Durability estimate = 59.000 cycles of
manoeuvre.
Warnings – The estimate of durability is performed on the basis of the design
calculations and the results of tests carried out on prototypes. In fact, being an
estimate, it does not give any guarantee on the actual duration of the product.
GRAPH A
demand index (%)
cycles of manoeuvres
DURABILITY OF THE PRODUCT
Demand index
> 100 Kg 10 %
Leaf weight:
> 200 Kg 20 %
> 300 Kg 30 %
> 400 Kg –
Leaf length: (1 ÷ 2 m) 20 %
Operating temperature: 20 %
Blind leaf: 15 %
Installation in windy area: 15 %
TABLE 2
CE declaration of conformity
and declaration of incorporation of “quasi-ma-
chine”
Declaration in accordance with Directives: 2004/108/EC (EMC);
2006/42/EC (MD) annex II, part B
Note: The content of this declaration corresponds to declaration made in
the official document filed in the offices of Nice S.p.a., and particularly the
latest version thereof available prior to the printing of this manual. The text
herein has been re-edited for editorial purposes. A copy of the original
declaration may be requested from Nice S.p.a. (TV) I.
Declaration number: 462/WINGO4024
Revision: 0
Language: IT
Name of manufacturer: NICE S.p.A.;
Address: Via Pezza Alta N°13, 31046 Rustignè di Oderzo (TV) Italy;
Person authorized to provide technical documentation: Mr. Oscar
Marchetto;
Address: Via Pezza Alta N°13, 31046 Rustignè di Oderzo (TV) Italy;
Product type: 24 V D.C. electromechanical gearmotor for swing gate;
Model / Type : Wingo4024;
Accessories: none.
The undersigned Luigi Paro, as Managing Director, hereby declares
under his own responsibility that the product identified above complies
with the provisions of the following directives:
• DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND
COUNCIL of December 15 2004 concerning alignment of Member
States’ legislation regarding electromagnetic compatibility and abro-
gating directive 89/336/EEC, according to the following harmonized
standards: EN 61000-6-2:2005, EN 61000-6-3:2007.
The product also complies with the following directive in accordance
with the requirements for “quasi-machines”:
• Directive 2006/42/EC OF THE EUROPEAN PARLIAMENT AND
COUNCIL of 17 May 2006 regarding machines and amending direc-
tive 95/16/EC (consolidated text).
– I declare that the pertinent technical documentation has been pre-
pared in accordance with Annex VII B to Directive 2006/42/EC and
that the following essential requirements have been met: 1.1.1- 1.1.2-
1.1.3- 1.2.1-1.2.6- 1.5.1-1.5.2- 1.5.5- 1.5.6- 1.5.7- 1.5.8- 1.5.10-
1.5.11.
– The manufacturer agrees to send the national authorities pertinent
information on the “quasi-machine” in response to a motivated re-
quest without affecting its intellectual property rights.
– If the “quasi-machine” is operated in a European country with an of-
ficial language other than the language used in this declaration, the
importer must associate a translation with this declaration.
– The “quasi-machine” must not be operated until the final machine in
which it is to be incorporated is declared to conform to the provisions
of Directive 2006/42/EC, if applicable to it.
The product also complies with the following standards: EN 60335-
1:2002 + A1:2004 + A11:2004 + A12:2006 + A2:2006 + A13:2008 +
A14:2010, EN 60335-2-103:2003
The parts of the product which are subject to the following standards
comply with them: EN 13241-1:2003, EN 12445:2002, EN
12453:2002, EN 12978:2003.
Oderzo, 13.06.12
Mr. Luigi Paro
(Managing Director)
To Next Page
Loading...
Need help?
General
