Enlever toutes les pièces du carton, les organiser selon les numéros de pièce indiqués sur la liste et vous assurer que les
quantités des pièces sont correctes.
ÉTAPE 1 Insérer cinq roulettes (2) dans la base (1), les pousser très fort jusqu’à ce que vous entendiez ou sentiez la roulette (2) s’enclencher. Insérer le vérin
pneumatique (3) dans la base (1) et glisser les soufflets (4) sur le vérin pneumatique (3).
ÉTAPE 2 Fixer les accoudoirs (8L et 8R) au coussin du siège (7) en utilisant un bouton (9), une rondelle plate (10) et une rondelle en étoile (11) pour chaque
accoudoir (8). RESSERRER COMPLÈTEMENT TOUS LES BOUTONS (9).
ÉTAPE 3 Fixer le mécanisme (5) au coussin du siège (7) avec six vis du mécanisme (12). RESSERRER COMPLÈTEMENT TOUTES LES VIS DU
MÉCANISME (12).
ÉTAPE 4 Fixer le support du dossier (17) au dossier (6) avec des vis du montage du dossier (13). RESSERRER COMPLÈTEMENT TOUTES LES VIS
DE SUPPORT DU DOSSIER (13).
ÉTAPE 5 Insérer le support du dossier (17) dans l’arrière du mécanisme (5) et fixer avec des vis du montage du dossier (15), d’une rondelle plate (10) et d’une
rondelle en étoile (11). Fixer la couverture du support du dossier (16) au support du dossier (17) avec deux vis de support de dossier (14). RESSERRER
COMPLÈTEMENT TOUTES LES VIS.
ÉTAPE 6 Placer le siège assemblé sur le vérin pneumatique (3) et mettre de la pression.
ATTENTION : AVANT D’UTILISER LE FAUTEUIL, VOUS ASSURER D’AVOIR RESSERRÉ COMPLÈTEMENT TOUTES LES VIS.
92893
MANAGER’S CHAIR
OPERATING INSTRUCTIONS
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and
knobs are securely tightened.
3. Check that all bolts screws and knobs are tight every
three months or as needed.
4. Do not overturn back tilt knob when decreasing
tension.
5. Dispose of packing material properly. Do not use
plastic cover as head covering. It may cause
suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.
LIMITED WARRANTY
Pro-Line II chairs are warranted* from the date of purchase against failure due to material and workmanship as follows:
•Lifetimeoncomponentpartsincludingpneumaticcylinder,controlmechanism,baseandcasters.
•3Yearsonupholsteryfabricandfoamagainstwearanddeterioration.
Tomakeawarrantyclaim,contactPartsDepartment.Providemodelnumberanddescriptionoftheproblemandobtainreturnauthorization.
Atit’soptionOfceStarProductswill:
(a)Supplycompatiblecomponentsofcurrentmanufacture.
(b)Repairthecustomer’scomponent.Thecustomermustprepayfreightonanycomponentsreturnedtothefactory.
ReturnfreightoncomponentsstillinwarrantywillbepaidbyOfceStarProducts.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs. or
less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other
event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or
consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a five
year warranty on all parts applies. Fabric and foam is warranted for one year. Thiswarrantygivesyouspeciclegalrights,andyoumayalsohaveotherrights
whichvaryfromstatetostate.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts
are damaged or missing. Our Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail
parts@officestar.net, by Fax 1-909-930-5629, or toll free parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00
p.m. Pacific Time.
FEATURES
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and pull lever (4) up.
Tolowerseatheightsitonchairandpulllever(4)up.
• SEAT ANGLE ADJUSTMENT
To adjust seat angle, lift lever (2). Leave lever up for free float or
pushlever(2)downtolock.
• BACKREST ANGLE ADJUSTMENT
To adjust back angle lift lever (1). Leave lever (1) up for free
oatorpushlever(1)downtolockatanyangle.
• SEAT SLIDER ADJUSTMENT
Toslideseatforwardorbackward,pullhandlebar(3)out.
Release handle bar (3) to lock desired seat position.
• TILT TENSION ADJUSTMENT
Toadjusttitletension,Turnknob(6)clockwisetoincrease
tensionandcounter-clockwisetodecreaseoreasethetension.
• SEAT/BACK ANGLE ADJUSTMENT & FORWARD TILT
To adjust Seat/Back angle, lift lever (2) leave lever up for free
float orpushleverdowntolock.Forforwardtiltleanbackwith
lever(2)inthedownpositionandpushlever(5)forward.Lift
lever(2)andtheseatwillltiltforwardforkeyboard
intensive activities.
• ARM HEIGHT ADJUSTMENT
Toadjustarmheight,pushbuttom(7)toallowthearmstomove
upordownfreely.Releasebuttom(7)oncethedesired
height is reached.
• ARM WIDTH ADJUSTMENT
Toadjustarmwidth,loosenknob(8)toallowthearmstomove
inandoutfreely.tightenknob(8)oncethedesiredwidthisreached.
© Office Star Products Janvier 2012
92893
FAUTEUIL DE DIRECTION
INSTRUCTIONS DE MONTAGE
PIÈCE QTÉ
1. Base .......................1
2. Roulettes ....................5
3. Vérin pneumatique ............1
4. Soufflet .....................1
5. Mécanisme ..................1
6. Dossier .....................1
7. Coussin du siège ..............1
8. Accoudoir (8L et 8R) ...........2
9. Bouton ......................2
10. Rondelle plate ...............3
11. Rondelle en étoile ............3
12. Vis du mécanisme ............6
13. Vis du support du dossier ......1
14. Vis de la couverture du dossier . . 2
15. Vis du montage du dossier .....1
16. Couvercle de support du dossier . 1
17. Support du dossier ...........1
18. Clé Allen (non montré) .........2
1
2
3
4
5
6
7
8
2
3
5
4
7
6
8L
1
8R
9
10
11
12
13
14
16
17
9
10
11
11
10
15