䂓
䊍䊷䉺ᢿ✢⼊ႎ䊶䊍䊷䉺ㆊ㔚ᵹᬌ⼊ႎ
䇭㩷䊶SSR㓚ᬌ⼊ႎ䋨CT1䊶CT2䋩
• 䗮ֵ䆒ᅮ˄՟བ˖䗮ֵ䗳⥛˅ᖙ乏ϢϞԡᴎϔ㟈DŽ
•
ᬃᣕҹϟ䗮ֵ䆂˖Compoway/F (Sysway) ModbusDŽৃ㓪ൟোϡᬃᣕSYSWAY䗮ֵ䆂DŽ
• E53-CNQ01N2ǃE53-CN01N2E53-CNH01N2া䰤Ѣৡ⿄ᏺ᳝Ā–HāĀ–HTā
ৢ㓔ⱘൟোDŽ৺߭ˈህӮᇐ㟈ᬙ䱰DŽ
䂓џӊ䕧ܹ
䂓ࡴ⛁఼ᮁ㒓䄺/
ࡴ⛁఼䖛⌕Ẕ⌟䄺㪆
HS䄺˄CT1/CT2˅
䂓䗮ֵ˄
RS-485㪆RS-232C
˅
• 㾘Ḑ:Ⳉ⌕12Vˈ21mA˄ᏺⷁ䏃ֱᡸ˅
䂓ࠊ䕧ߎ2˄䕧ߎ⬉˅
• 㾘Ḑ˖Ⳉ⌕12Vf10λˈ20mA˄ᏺⷁ䏃ֱᡸ˅
• 㽕ᡞES1B 㑶⛁Ӵᛳ఼ⱘ䚼⬉⑤Ў݊ҪⳂⱘՓ⫼ˈ䇋䆶OMRONҷ⧚ଚDŽ
ϡᕫ㒭ৡ⿄ᏺ᳝Ā–HāĀ–HTāৢ㓔ⱘൟো㗠ϡ᳝ES1BӴᛳ఼䕧ܹⱘൟোՓ⫼
(53-CNPHN2ˈE53-CNPBN2E53-CNP03N2DŽ
䂓ES1Bⱘ䚼⬉⑤
㦰䯈ߛᤶ
E5CN/E5CN-H/E5CN-HT䇭
᭄ᄫᓣ⏽ᑺࠊҾ
䗮ֵ
џӊ䕧ܹ
ࡴ⛁఼⚻ᮁ䄺
ࡴ⛁఼䖛⌕Ẕ⌟䄺
/
㩷
HS䄺˄CT1/CT2˅
ࠊ䕧ߎ2˄⬉䕧ߎ˅
⫼ѢES1Bⱘ䚼⬉⑤
䕀ᤶ䕧ߎ
ᛳ䇶ᙼ䌁фOMRON E5CN ⏽ᑺࠊ఼DŽՓ⫼ࠡᭀ䇋
䆺㒚䯙䇏ᴀݠDŽ䇋ཹֱㅵᴀݠҹᇚᴹখ㗗᠔䳔DŽ
ྚ啭݀ৌ
©All Rights Reserved
Ⳍկ⬉Ẕ⌟⬉⌕ؐⱘ䆒ゟ
• Փ⫼ҹϟ݀ᓣᴹ䆒ゟẔ⌟⬉⌕ؐ
• ᔧϾࡴ⛁఼䖲㟇CTᯊˈᡞ᳔ᇣⱘࡴ⛁఼⚻ᮁ⬉⌕ؐЎࡴ⛁఼ᮁ㒓⬉⌕ؐDŽ˄བᵰ᠔
᳝ࡴ⛁఼䛑Փ⫼Ⳍৠ⬉⌕ᇣˈ߭ᇚϔϾࡴ⛁఼ⱘᮁ㒓⬉⌕ؐЎ⚻ᮁؐDŽ˅
• ⹂ֱ⒵䎇ҹϟᴵӊ˖
ࡴ⛁఼Ꮉ⬉⌕ᇣѢ10.0Aᯊ˖ℷᐌⱘࡴ⛁఼⬉⌕ؐˉࡴ⛁఼ᮁ㒓⬉⌕ؐ
㻢
1A
ᔧ⬉⌕ؐᇣѢ1AᯊˈẔ⌟ࡳ㛑ϡৃ䴴DŽ
ࡴ⛁఼Ꮉ⬉⌕ㄝѢ㗙Ѣ10.0Aᯊ˖ℷᐌⱘࡴ⛁఼⬉⌕ؐˉࡴ⛁఼ᮁ㒓⬉⌕ؐ
㻢
2.5A
ᔧ⬉⌕ؐᇣѢ2.5AᯊˈẔ⌟ࡳ㛑ϡৃ䴴DŽ
•
Ẕ⌟⬉⌕ৃҹ䆒㕂Ў0.1A㟇49.9AЁⱘӏᛣؐDŽᔧẔ⌟⬉⌕㹿䆒㕂Ў0.0A㗙50.0Aᯊˈࡴ
⛁఼ᮁ㒓ϡӮ㹿Ẕ⌟DŽ䆒ᅮؐЎ0.0Aᯊˈ㒧ᵰᰃߛᤶࡴ⛁఼ᮁ㒓䄺ЎOFFDŽ
䆒ᅮؐЎ50.0Aᯊˈ㒧ᵰᰃߛᤶ䄺ЎONDŽ
• ᠔᳝ࡴ⛁఼ℷᐌᎹᯊⱘᘏ⬉⌕ؐϡᕫ催Ѣ50.0ADŽབᵰ⬉⌕ؐ催Ѣ55.0AˈĀࡴ⛁఼⬉⌕
ⲥ㾚āখ᭄ᰒ⼎ЎĀffffāDŽ
CT˖E54ˉCT1㗙E54ˉCT3DŽ˄⣀䌁ф˅
ϝⳌկ⬉ϟⱘⲥ⌟⬉⌕
•
ᔧՓ⫼ϝⳌկ⬉ᯊˈ䇏পϸ໘ⱘ⬉⌕ؐህ㛑ѻ⫳ࡴ⛁఼ᮁ㒓HS䄺఼DŽ㒓䏃㒚㡖খ㾕⫼᠋ݠDŽ
Ẕ⌟䆒ᅮ˙
ℷᐌᎹࡴ⛁఼⬉⌕ؐδࡴ⛁఼ᮁ㒓⬉⌕ؐ
2
2162869-1A
CHT6
ᣝ 䇭
ᇥѢ1⾦
ࠊᇚذℶDŽ
ࠊℷ䖯㸠
ࠊذℶ
ҷ㸼㦰ᬍব
᪡㦰
䗮䆃䆒ᅮ㦰
߱ྟ䆒ᅮ㦰
ҙ᳝䗮ֵⱘൟোᰒ⼎DŽ
ֱᡸ㦰
䇗ᭈ㦰
Ϟ⬉
催㑻ࡳ㛑
䆒ᅮ㦰
䕧ܹᆚⷕ
˄-169˅
䂓ৃ䗝䆒ᅮ߫㸼˄া߫ߎৃ䗝ܗⱘখ᭄˅
Փ⫼䇈ᯢк
CHN
ᣝ 䇭
ᇥѢ1⾦
ᣝ 䇭
ᇥѢ1⾦
䭓ᣝ
㟇ᇥ3⾦
䭓ᣝ
㟇ᇥ1⾦
䭓ᣝ
M
㟇ᇥ1⾦
䭓ᣝ
M
㟇ᇥ3⾦
ߛᤶࠄ䗮ֵ䆒ᅮ㦰
䭓ᣝ 䬂㟇ᇥ3⾦ˈҢ᪡㦰䕀ࠄ߱ྟ䆒ᅮ㦰ˈݡᣝ䬂
䕀ࠄ䗮ֵ䆒ᅮ㦰DŽ
gൟোЎ-500ⱘѻકˈ䇋ᅝ㺙E53-CNƶƶN2DŽ
g᳝Ā-HāĀ-HTāৢ㓔ⱘൟোϞᑊᰒ⼎ᶤѯ䆒ᅮDŽ
g᳝݇᪡ᣛ⼎ⱘ䆺㒚ֵᙃˈ䇋খ㗗E5CN/E5AN/E5EN⫼᠋ݠǃE5CN-H/E5EN-H/E5AN-H⫼᠋ݠ
E5CN-HT/E5EN-HT/E5AN-HT⫼᠋ݠDŽ
g᳝݇䗮ֵ㾘Ḑⱘ䆺㒚ֵᙃˈ䇋খ㗗E5CN/E5AN/E5EN䗮ֵݠǃE5CN-H/E5EN-H/E5AN-H䗮ֵݠ
E5CN-HT/E5EN-HT/E5AN-HT⫼᠋ݠDŽ
䏃SPǂ
ࡴ⛁఼⬉⌕1ؐⲥ㾚ǂ
ࡴ⛁఼⬉⌕2ؐⲥ㾚ǂ
ⓣ⬉⌕1ⲥ㾚ǂ
ⓣ⬉⌕2ⲥ㾚ǂ
䗮䆃ݭǂ
ࡴ⛁఼⬉⌕1ؐⲥ㾚ǂ
ࡴ⛁఼ᮁ㒓Ẕ⌟1ǂ
ࡴ⛁఼䖛⌕Ẕ⌟1
ࡴ⛁఼⬉⌕2ؐⲥ㾚
ࡴ⛁఼ᮁ㒓Ẕ⌟2ǂ
ࡴ⛁఼䖛⌕Ẕ⌟2
ⓣ⬉⌕1ⲥ㾚ǂ
HS䄺1ǂ
ⓣ⬉⌕2ⲥ㾚
HS䄺2
䆒ᅮ⚍0ǂ
䆒ᅮ⚍1ǂ
䆒ᅮ⚍2ǂ
䆒ᅮ⚍3ǂ
Փ⫼䏃SPⱘϾ᭄ǂ
џӊ䕧ܹ1ߚ䜡ǂ
џӊ䕧ܹ2ߚ䜡ǂ
䆂䗝ᢽǂ
ܗোǂ
䗮ֵ⊶⡍⥛ǂ
᭄↨⡍ǂ
ذℶ↨⡍ǂ
䗮䆃༛ي偠ǂ
থ䗕ㄝᕙᯊ䯈ǂ
Փ⫼䏃SPǂ
HBA ON/OFFǂ
ࡴ⛁఼ᮁ㒓䫕ᄬǂ
ࡴ⛁఼ᮁ㒓⒲ৢǂ
HS䄺Փ⫼
HS䄺䫕ᄬǂ
HS䄺⒲ৢ
ࡴ⛁఼䖛⌕Փ⫼
ࡴ⛁఼䖛⌕䮽䫕
ࡴ⛁఼䖛⌕⒲ৢ
᪡㦰
䇗ᭈ㦰
߱ྟ䆒ᅮ㦰
䗮ֵ䆒ᅮ㦰
催㑻ࡳ㛑䆒ᅮ
㦰
0㟇3
0.0㟇55.0
0.0㟇55.0
0.0㟇55.0
0.0㟇55.0
ON䇮OFF
0.0㟇55.0
0.0㟇50.0
0.0㟇55.0
0.0㟇55.0
0.0㟇50.0
0.0㟇55.0
0.0㟇55.0
0.0㟇50.0
0.0㟇55.0
0.0㟇50.0
䆒ᅮ⚍ϟ䰤㟇䆒ᅮ⚍Ϟ䰤 0
䆒ᅮ⚍ϟ䰤㟇䆒ᅮ⚍Ϟ䰤
䆒ᅮ⚍ϟ䰤㟇䆒ᅮ⚍Ϟ䰤 0
䆒ᅮ⚍ϟ䰤㟇䆒ᅮ⚍Ϟ䰤
0㟇2
0㟇
㪈㪇
0㟇㪈㪇
Compoway/F(Sysway),Modbus
0㟇99
1.2ˈ2.4ˈ4.8ˈ9.6ˈ19.2ˈ38.4ˈ57.6
7ˈ8
1ˈ2
᮴ˈ يˈ ༛
ᢙ
0㟇99
ON䇮OFF
ON䇮OFF
ON䇮OFF
0.1㟇50.0
ON䇮OFF
ON䇮OFF
0.1㟇50.0
ON䇮OFF
ON䇮OFF
0.1㟇50.0
0
OFF
0.0
0.0
50.0
50.0
0
0
1
0
1
Compoway/F
1
9.6
7
2
20
OFF
ON
OFF
0.1
ON
OFF
0.1
ON
OFF
0.1
NA
A
A
A
A
NA
A
A
A
A
A
A
A
A
A
A
EU
EU
EU
EU
NA
NA
NA
NA
NA
kbps
Bits
Bits
NA
ms
NA
NA
NA
A
NA
NA
A
NA
NA
A
m-sp
ct1
ct2
lcr1
lcr2
cmwt
ct1
hb1
oc1
ct2
hb2
oc2
lcr1
hs1
lcr2
hs2
sp-0
sp-1
sp-2
sp-3
ev-m
ev-1
ev-2
psel
u-no
bps
len
sbit
prty
sdwt
mspu
hbu
hbl
hbh
hsu
hsl
hsh
ocu
ocl
och
㦰 䆒ᅮ ᰒ⼎ 䆒ᅮؐⲥ㾚ؐ 㔎ⳕؐԡ
᳔2⚍
㞾ࡼࡼˈ䕀ᤶℷড᪡ˈSPᓣߛᤶˈ100% ATᠻ㸠প⍜ˈ
40% ATᠻ㸠প⍜ˈ䆒ᅮᬍব⫼⽕⫼ˈ䗮ֵݭܹ⫼⽕⫼ˈ䄺䮽䫕প⍜ㄝ
ǂǂǂǂǂON˖᳔1k㱅ǃOFF˖᳔ᇣ100k㱅
ǂǂǂǂǂON˖⅟ԭ⬉᳔1.5VǃOFF˖ⓣ⬉⌕᳔0.1mA
ǂǂǂǂǂON˖㒜ッ⬉⌕˖㋘7mAⷁ䏃
䕧᭄ܹ
ࡳ㛑
䕧ܹ㾘Ḑ
㾺⚍䕧ܹ
䴲㾺⚍䕧ܹ
䂓䕀ᤶ䕧ߎ
䂓⸳ቯ䊥䉴䊃৻ⷩ䋨䉥䊒䉲䊢䊮ᯏ⢻䈮㒢ቯ䋩
䂓䉟䊔䊮䊃ജ
ᬌ㔚ᵹ୯䈱᳞䉄ᣇ䋨න⋧䈪䊍䊷䉺ᢿ✢⼊ႎ䈱႐ว䋩
䊶ᰴ䈱ᑼ䈪⸳ቯ୯䉕᳞䉄䈩䈒䈣䈘䈇䇯
䊶䊍䊷䉺䉕䋲ᧄએCT䈮ㅢ䈚䈢䈫䈐䈱ᢿ✢ᤨ䈱㔚ᵹ୯䈲䇮ᦨ䉅ዊ䈘䈇㔚ᵹ୯䈱䊍䊷䉺䈏ᢿ✢䈚䈢䈫䈐䈱୯
䈫䈚䈩䈒䈣䈘䈇䇯䋨䈜䈼䈩ห䈛㔚ᵹ୯䈱䈫䈐䈲䇮䋱ᧄ䈏ᢿ✢䈚䈢䈫䈐䈱୯䋩
䊶ᰴ䈱᧦ઙ䉕ḩ䈢䈜䉋䈉䈮䈚䈩䈒䈣䈘䈇䇯
䇭㪈㪇㪅㪇Aᧂḩ䈱䊍䊷䉺䋺ᱜᏱ୯䈱㔚ᵹ୯䋭ᢿ✢ᤨ䈱㔚ᵹ୯㻢1A
䇭1Aᧂḩ䈱䈫䈐䈲ᬌ䈏ቯ䈮䈭䉍䉁䈜䇯
䇭10.0Aએ䈱䊍䊷䉺䋺ᱜᏱ୯䈱㔚ᵹ୯䋭ᢿ✢ᤨ䈱㔚ᵹ୯㻢2.5A
䇭2.5Aᧂḩ䈱䈫䈐䈲ᬌ䈏ቯ䈮䈭䉍䉁䈜䇯
䊶⸳ቯ୯䈱▸࿐䈲0.1䌾49.9A䈪䈜䇯⸳ቯ୯䈏䇸㪇㪅㪇䇹䉁䈢䈲䇸㪌㪇㪅㪇䇹䈱䈫䈐䈲䇮䊍䊷䉺ᢿ✢ᬌ䉕ⴕ䈇䉁䈞䉖
䌿䇸㪇㪅㪇䇹䈱䈫䈐䈲䇮䊍䊷䉺ᢿ✢⼊ႎ㪔䇸OFF䇹䍂䇸㪌㪇㪅㪇䇹䈱䈫䈐䈲䊍䊷䉺ᢿ✢⼊ႎ䋽䇸ON䇹䈫䈭䉍䉁䈜䇯
䊶䊍䊷䉺䈱ᱜᏱ㔚ᵹ୯䈱ว⸘䈲䇮50Aએ䈫䈚䈩䈒䈣䈘䈇䇯55.0A䉕䈋䉎䈫䈐䈲䇮䇸䊍䊷䉺㔚ᵹ୯䊝䊆䉺䇹
䊌䊤䊜䊷䉺䈪䈲䇮䇸ffff䇹䉕␜䈚䉁䈜䇯
㪚㪫䈲ᄁ䈱ᒻ㪜㪌㪋㪄㪚㪫㪈䋨ⓣᓘ㱢㪌㪅㪏䋩䉁䈢䈲ᒻ㪜㪌㪋㪄㪚㪫㪊䋨ⓣᓘ㱢㪈㪉䋩䉕䈗↪䈒䈣䈘䈇䇯
ᬌ㔚ᵹ୯䈱᳞䉄ᣇ䋨䋳⋧䈱႐ว䋩
䊶3⋧㔚Ḯ䉕䈗↪䈱႐ว䇮2䉬ᚲ䈱㔚ᵹ୯䉕⺒䉂ㄟ䉃䈖䈫䈪䇮䊍䊷䉺ᢿ✢䊶SSR㓚䈱ᬌ䈏น⢻䈪䈜䇯
㩷㩷⚦䈭⚿✢ᣇᴺ䈭䈬䈲䇮䊡䊷䉱䊷䉵䊙䊆䊠䉝䊦䉕ෳ⠨䈮䈚䈩䈗↪䈒䈣䈘䈇䇯
䂓ㅢାᯏ⢻䋨RS-485䊶RS-232C䋩
⸳ቯ୯䋽
ᱜᏱᤨ䈱㔚ᵹ୯䋫ᢿ✢ᤨ䈱㔚ᵹ୯
2
ᒻE5CN/ᒻE5CN-H/ᒻE5CN-HT䇭
䊂䉳䉺䊦⺞▵⸘
ㅢାᯏ⢻
䇭䉟䊔䊮䊃ജ
䇭
䊍䊷䉺ᢿ✢⼊ႎ䊶䊍䊷䉺ㆊ㔚ᵹᬌ⼊ႎ
䇭㩷㪪㪪㪩㓚ᬌ⼊ႎ䋨㪚㪫㪈䊶㪚㪫㪉䋩
䇭ᓮജ㪉䋨㔚ജ䋩
䇭ᒻ
ES1B
↪ᄖㇱଏ⛎㔚Ḯ
䇭વㅍജ
ขᛒ⺑ᦠ
䉥䊛䊨䊮ຠ䉕䈍⾈䈇䈕䈇䈢䈣䈐䈅䉍䈏䈫䈉䈗䈙䈇䉁䈜䌿
䈖䈱ຠ䉕ో䈮ᱜ䈚䈒↪䈚䈩䈇䈢䈣䈒䈢䉄䈮䇮㔚᳇䈱⍮⼂
䉕䈜䉎ኾ㐷ኅ䈏ᛒ䈦䈩䈒䈣䈘䈇䇯
䈍䈇䈮䈭䉎೨䈮䈖䈱ขᛒ⺑ᦠ䉕䈍⺒䉂䈮䈭䉍䇮චಽ䈮
䈗ℂ⸃䈒䈣䈘䈇䇯䈍⺒䉂䈮䈭䈦䈢ᓟ䉅䇮䈇䈧䉅ᚻర䈮⟎䈇䈩
䈗↪䈚䈩䈒䈣䈘䈇䇯
©All Rights Reserved
JPN
ㅢା⸳ቯ䊧䊔䊦䈻䈱⒖ⴕ
ㆇォ䊧䊔䊦䈎䉌䇭㩷㩷㩷䉨䊷䉕㪊⑽એ䈚䇮ೋᦼ⸳ቯ䊧䊔䊦䈮⒖ⴕ䈚䈢ᓟ䇮
䈘䉌䈮䇭㩷㩷㩷䉨䊷䉕䈚䈩䈇䈢䈣䈒䈫ㅢା⸳ቯ䊧䊔䊦䈮⒖ⴕ䈚䉁䈜䇯䇭
䊧䊔䊦䈱ಾ䉍ᦧ䈋ᣇᴺ
ᓮ䈏ᱛ䈚䉁䈜
ᓮ
ᓮᱛ
䊧䊔䊦⒖ⴕ
ㆇォ䊧䊔䊦
ㅢା⸳ቯ䊧䊔䊦
ೋᦼ⸳ቯ䊧䊔䊦
ㅢାᯏ⢻ઃ䈐ᯏ⒳䈱䉂
␜䈘䉏䉁䈜䇯
䊒䊨䊁䉪䊃䊧䊔䊦
⺞ᢛ䊧䊔䊦
䇭䉨䊷
㪈⑽ᧂḩ
䇭䉨䊷
㪊⑽એ
䇭䉨䊷
㪈⑽એ
䇭䉨䊷
㪈⑽એ䈪ὐṌ
䇭㪂䇭㩷㩷䉨䊷
㪈⑽એ
䇭䉨䊷
㪈⑽ᧂḩ
䇭㪂䇭㩷㩷䉨䊷
㪊⑽એ
㜞ᯏ⢻⸳ቯ䊧䊔䊦
䇭䉨䊷
㪈⑽એ
䊌䉴䊪䊷䊄
ജ
㪄㪈㪍㪐
ᦨᄢ䋲ὐ
䉥䊷䊃㪆䊙䊆䊠䉝䊦䇮ᱜㅒォ䇮SP䊝䊷䊄ಾᦧ䇮100%㪘㪫ታⴕ㪆ᱛ䇮40%㪘㪫ታⴕ㪆ᱛ䇮
⸳ቯᄌᦝ⸵น㪆ᱛ䇮ㅢାᦠㄟ䉂ᱛ㪆⸵น䇮⼊ႎ䊤䉾䉼⸃㒰䇭╬
䇭䇭䇭䇭䇭㩷㩷㩷㩷㩷ON䋺㪈㫂㱅એ䇮㪦㪝㪝䋺㪈㪇㪇㫂㱅એ
䇭䇭䇭䇭䇭㩷㩷㩷㩷㩷ON䋺ᱷ⇐㔚1.5Vએ䇮OFF䋺ṳ䉏㔚ᵹ0.1mAએ
䇭䇭䇭䇭䇭㩷㩷㩷㩷㩷ONᤨ┵ሶ㔚ᵹ䋺⚂7mA㩿⍴⛊㪀
ജὐᢙ
ᯏ⢻
ജ᭽
ធὐ
ήធὐ
䊙䊦䉼㪪㪧
䊍䊷䉺㔚ᵹ୯㪈䊝䊆䉺
䊍䊷䉺㔚ᵹ୯㪉䊝䊆䉺
ṳ䉏㔚ᵹ୯㪈䊝䊆䉺
ṳ䉏㔚ᵹ୯㪉䊝䊆䉺
ㅢାᦠㄟ
䊍䊷䉺㔚ᵹ୯㪈䊝䊆䉺
䊍䊷䉺ᢿᬌ㪈
䊍䊷䉺ㆊ㔚ᵹᬌ㪈
䊍䊷䉺㔚ᵹ୯㪉䊝䊆䉺
䊍䊷䉺ᢿᬌ㪉
䊍䊷䉺ㆊ㔚ᵹᬌ㪉
ṳ䉏㔚ᵹ୯㪈䊝䊆䉺
㪪㪪㪩㓚ᬌ㪈
ṳ䉏㔚ᵹ୯㪉䊝䊆䉺
㪪㪪㪩㓚ᬌ㪉
⋡ᮡ୯㪇
⋡ᮡ୯㪈
⋡ᮡ୯㪉
⋡ᮡ୯㪊
䊙䊦䉼㪪㪧↪ᢙ
䉟䊔䊮䊃ജഀઃ㪈
䉟䊔䊮䊃ജഀઃ㪉
䊒䊨䊃䉮䊦ㆬᛯ
ㅢା䊡䊆䉾䊃㪥㫆㪅
ㅢାㅦᐲ
ㅢା䊂䊷䉺㐳
ㅢା䉴䊃䉾䊒䊎䉾䊃
ㅢା䊌䊥䊁䉞
ㅍାᓙ䈤ᤨ㑆
䊙䊦䉼㪪㪧↪
䊍䊷䉺ᢿ↪
䊍䊷䉺ᢿ䊤䉾䉼
䊍䊷䉺ᢿ䊍䉴䊁䊥䉲䉴
㪪㪪㪩㓚↪
㪪㪪㪩㓚䊤䉾䉼
㪪㪪㪩㓚䊍䉴䊁䊥䉲䉴
䊍䊷䉺ㆊ㔚ᵹ↪
䊍䊷䉺ㆊ㔚ᵹ䊤䉾䉼
䊍䊷䉺ㆊ㔚ᵹ䊍䉴䊁䊥䉲䉴
ㆇォ䊧䊔䊦
⺞ᢛ䊧䊔䊦
ೋᦼ⸳ቯ䊧䊔䊦
ㅢା⸳ቯ䊧䊔䊦
㜞ᯏ⢻⸳ቯ䊧䊔䊦
㩷 䊧䊔䊦㩷 ⸳ቯ䊂䊷䉺㩷 㩷
䉨䊞䊤䉪䉺
㩷䇭䇭䇭䇭䇭䇭䇭䇭⸳ቯ㩿䊝䊆䉺㪀୯䇭䇭㩷䇭䇭䇭䇭䇭䇭䇭㩷ೋᦼ୯䇭䇭䇭㩷න
㪇䌾㪊
㪇㪅㪇䌾㪌㪌㪅㪇
㪇㪅㪇䌾㪌㪌㪅㪇
㪇㪅㪇䌾㪌㪌㪅㪇
㪇㪅㪇䌾㪌㪌㪅㪇
ON䇮OFF
㪇㪅㪇䌾㪌㪌㪅㪇
㪇㪅㪇䌾㪌㪇㪅㪇
㪇㪅㪇䌾㪌㪌㪅㪇
㪇㪅㪇䌾㪌㪌㪅㪇
㪇㪅㪇䌾㪌㪇㪅㪇
㪇㪅㪇䌾㪌㪌㪅㪇
㪇㪅㪇䌾㪌㪌㪅㪇
㪇㪅㪇䌾㪌㪇㪅㪇
㪇㪅㪇䌾㪌㪌㪅㪇
㪇㪅㪇䌾㪌㪇㪅㪇
⋡ᮡ୯䊥䊚䉾䊃㒢୯䌾⋡ᮡ୯䊥䊚䉾䊃㒢୯
⋡ᮡ୯䊥䊚䉾䊃㒢୯䌾⋡ᮡ୯䊥䊚䉾䊃㒢୯
⋡ᮡ୯䊥䊚䉾䊃㒢୯䌾⋡ᮡ୯䊥䊚䉾䊃㒢୯
⋡ᮡ୯䊥䊚䉾䊃㒢୯䌾⋡ᮡ୯䊥䊚䉾䊃㒢୯
㪇䌾㪉
㪇䌾㪈㪇
㪇䌾㪈㪇
Compoway/F(Sysway)䇮Modbus
㪇䌾㪐㪐
㪈㪅㪉䇮㪉㪅㪋䇮㪋㪅㪏䇮㪐㪅㪍䇮㪈㪐㪅㪉䇮㪊㪏㪅㪋䇮㪌㪎㪅㪍
㪎䇮㪏
㪈䇮㪉
䈭䈚䇮ᢙ䇮ᄸᢙ
㪇䌾㪐㪐
ON䇮OFF
ON䇮OFF
ON䇮OFF
㪇㪅㪈䌾㪌㪇㪅㪇
ON䇮OFF
ON䇮OFF
㪇㪅㪈䌾㪌㪇㪅㪇
ON䇮OFF
ON䇮OFF
㪇㪅㪈䌾㪌㪇㪅㪇
㪇
OFF
㪇㪅㪇
㪇㪅㪇
㪌㪇㪅㪇
㪌㪇㪅㪇
㪇
㪇
㪇
㪇
㪈
㪇
㪈
Compoway/F
㪈
㪐㪅㪍
㪎
㪉
ᢙ
㪉㪇
OFF
ON
OFF
㪇㪅㪈
ON
OFF
㪇㪅㪈
ON
OFF
㪇㪅㪈
䈭䈚
A
A
A
A
䈭䈚
A
A
A
A
A
A
A
A
A
A
EU
EU
EU
EU
䈭䈚
䈭䈚
䈭䈚
䈭䈚
䈭䈚
kbps
䊎䉾䊃
䊎䉾䊃
䈭䈚
ms
䈭䈚
䈭䈚
䈭䈚
A
䈭䈚
䈭䈚
A
䈭䈚
䈭䈚
A
m-sp
ct1
ct2
lcr1
lcr2
cmwt
ct1
hb1
oc1
ct2
hb2
oc2
lcr1
hs1
lcr2
hs2
sp-0
sp-1
sp-2
sp-3
ev-m
ev-1
ev-2
psel
u-no
bps
len
sbit
prty
sdwt
mspu
hbu
hbl
hbh
hsu
hsl
hsh
ocu
ocl
och
䂓Event input
Transition between levels
E5CN/E5CN-H/E5CN-HT
Digital Controller䇭
Communication
Event Input
Heater Burnout Alarm/
Heater Overcurrent Detection Alarm
Heater Short Alarm (CT1/CT2)
Control Output 2 (Voltage Output)
External Power Supply for ES1B
Transfer output
Press :
(less than
1 second).
Press :
(less than
1 second).
䂓Heater Burnout Alarm/Heater Short Alarm (CT1/CT2)
Establishing a value for the detection current for Single phase Power
• Use the following formula to establish a value for the detection current:
• When more than one heater is connected to the CT, use the burnout current of the heater using
the smallest current as the burnout value. (If all the heaters use the same size current, use the
value applicable to one heater as the burnout value.)
• Ensure that the following conditions are satisfied:
Heaters of less than 10.0A: Normal heater current value - Heater burnout current value
≥
1A
The detection function is unreliable for currents of less than 1A.
Heaters of 10.0A or more: Normal heater current value - Heater burnout current value
≥
2.5A
The detection function is unreliable for currents of less than 2.5A.
• The detection current can be set to anything from 0.1 to 49.9A. Heater burnout will not be
detected if the detection current is set to 0.0 or 50.0. Setting the value to 0.0 will have the effect
of switching the heater burnout alarm off; setting the value to 50.0 will have the effect of
switching the alarm on.
• The aggregate of the heaters' normal current values should not be more than 50.0A. If the value
exceeds 55.0A, the "heater current monitor" parameter will show "ffff".
CTs: E54-CT1 or E54-CT3. (available separately)
Finding the Detection Current for 3-phase Power
• When using 3-phase power, Heater burnout or HS alarms is available by reading the current
from two locations. Refer to the User's Manual for details on wiring.
Detection setting =
Normal heater current value + Heater burnout current value
2
Press 䇭
(less than 1 second)
Transition to Communication setting level
Press the 䇭 key for at least three seconds to move from the operation
level to the initial setting level; press the 䇭 key once again to move to
the communication setting level.
Hold 䇭 down
for at least
3 seconds
Hold 䇭 down
for at least
1 second
Hold 䇭+ M down
for at least 1 second
Hold 䇭+ M down
for at least 3 seconds
Control will stop.
Control in progress
Control stopped
Level change
Operation
level
Communication
setting level
Initial setting level
Displayed only for models
with communications.
Protect level
Adjustment
level
Advanced function
setting level
Input
password
(-169).
䂓
Options Settings List (Only parameters for option unit are listed.)
Thank you for purchasing the OMRON E5CN tempera-
ture controller. Read this manual carefully before using
the controller and always keep it close at hand while the
controller is in use.
OMRON CORPORATION
©All Rights Reserved
㪠㫅㫊㫋㫉㫌㪺㫋㫀㫆㫅㩷㪤㪸㫅㫌㪸㫃
EN
Operation
level
Adjustment
level
ޓޓޓޓޓInitial setting
ޓޓlevel
Communi-
cations
setting
level
Advanced
function
setting
level
0
OFF
0.0
0.0
50.0
50.0
0
0
0
0
1
0
1
Compoway/F
1
9.6
7
2
Even
20
OFF
ON
OFF
0.1
ON
OFF
0.1
ON
OFF
0.1
NA
A
A
A
A
NA
A
A
A
A
A
A
A
A
A
A
EU
EU
EU
EU
NA
NA
NA
NA
NA
kbps
Bits
Bits
NA
ms
NA
NA
NA
A
NA
NA
A
NA
NA
A
m-sp
ct1
ct2
lcr1
lcr2
cmwt
ct1
hb1
oc1
ct2
hb2
oc2
lcr1
hs1
lcr2
hs2
sp-0
sp-1
sp-2
sp-3
ev-m
ev-1
ev-2
psel
u-no
bps
len
sbit
prty
sdwt
mspu
hbu
hbl
hbh
hsu
hsl
hsh
ocu
ocl
och
Level Setting Display Set value/monitor value Default Unit
0 to 3
0.0 to 55.0
0.0 to 55.0
0.0 to 55.0
0.0 to 55.0
ON, OFF
0.0 to 55.0
0.0 to 50.0
0.0 to 55.0
0.0 to 55.0
0.0 to 50.0
0.0 to 55.0
0.0 to 55.0
0.0 to 50.0
0.0 to 55.0
0.0 to 50.0
Set point lower limit to set point upper limit
Set point lower limit to set point upper limit
Set point lower limit to set point upper limit
Set point lower limit to set point upper limit
0 to 2
0 to 10
0 to 10
Compoway/F(Sysway)䇮Modbus
0 to 99
1.2, 2.4, 4.8, 9.6, 19.2, 38.4,57.6
7, 8
1, 2
None, even, odd
0 to 99
ON, OFF
ON, OFF
ON, OFF
0.1 to 50.0
ON, OFF
ON, OFF
0.1 to 50.0
ON, OFF
ON, OFF
0.1 to 50.0
Contact input
No-contact input
• 4ࠄ20 mAˈܕ䆌䋳㥋⬉ᛳ˖᳔600 Ωˈߚ䕼⥛˖㑺10,000DŽ
•
E53-CNQFN2E53-CNBFN2া䰤Ѣৡ⿄ᏺ᳝Ā–HāĀ–HTāৢ㓔ⱘൟোDŽ৺߭ˈህӮᇐ㟈ᬙ䱰DŽ
Multi-SP
Heater current 1 value monitor
Heater current 2 value monitor
Leakage current 1 monitor
Leakage current 2 monitor
Communications writing
Heater current 1 value monitor
Heater burnout detection 1
Heater Overcurrent Detection 1
Heater current 2 value monitor
Heater burnout detection 2
Heater Overcurrent Detection 2
Leakage current 1 monitor
HS alarm 1
Leakage current 2 monitor
HS alarm 2
Set point 0
Set point 1
Set point 2
Set point 3
Number of multi-SP uses
Event input 1 allocation
Event input 2 allocation
Protocol selection
Unit No.
Communications baud rate
Data bits
Stop bits
Communications parity
Send wait time
Multi-SP use
HBA ON/OFF
Heater burnout latch
Heater burnout hysteresis
HS alarm use
HS alarm latch
HS alarm hysteresis
Heater Overcurrent Use
Heater Overcurrent Latch
Heater Overcurrent Hysteresis
Number of inputs
Functions
Input specifications
2 points max.
Auto/Manual, Invert Direct/Reverse Operation, SP Mode Switch, 100% AT Execute/
Cancel, 40% AT Execute/Cancel, Setting Change Enable/Disable, Communications
Write Enable/Disable, Alarm Latch Cancel, etc.
䇭䇭䇭䇭䇭 ON䋺1kΩ max., OFF䋺100kΩ min.
䇭䇭䇭䇭䇭 ON䋺residual voltage1.5V max.㪃㩷OFF䋺leakage current 0.1mA㩷max.
䇭䇭䇭䇭䇭 ON terminal current䋺Approx. 7mA(short-circuit)
Power on
㔚Ḯᛩ
䊶-500䉺䉟䊒䈲ᒻE53-CN**N2䉕ข䉍ઃ䈔䈩䈗↪䈒䈣䈘䈇䌿
䊶䇸-H䉺䉟䊒䇹䇸-HT䉺䉟䊒䇹䈮䈲␜䈘䉏䈭䈇⸳ቯ䊂䊷䉺䈏䈅䉍䉁䈜䇯
䊶ᧄᯏ䈱⚦䈭↪ᣇᴺ䈲䇮ౠ䇸ᒻE5CN/AN/EN䊡䊷䉱䊷䉵䊙䊆䊠䉝䊦䇹䇸ᒻE5CN-H/E5AN-H/E5EN-H䊡䊷䉱䊷䉵䊙䊆䊠䉝䊦䇹
㩷㩷䇸ᒻE5CN-HT/E5AN-HT/E5EN-HT䊡䊷䉱䊷䉵䊙䊆䊠䉝䊦䇹䉕ෳᾖ䈚䈩䈒䈣䈘䈇䇯
䊶ㅢା᭽䈱⚦䈲ౠ䇸ᒻE5CN/AN/ENㅢା䊙䊆䊠䉝䊦䇹䇸ᒻE5CN-H/E5AN-H/E5EN-Hㅢା䊙䊆䊠䉝䊦䇹䇸ᒻE5CN-HT/E5AN-HT/
E5EN-HTㅢା䊙䊆䊠䉝䊦䇹䉕ෳᾖ䈚䈩䈒䈣䈘䈇䇯
䊶
ㅢା䈱ฦ⒳⸳ቯ䋨ㅢାㅦᐲ╬䋩䈲䇮䉮䊮䊏䊠䊷䉺䈫ᧄᯏ䈏৻⥌䈚䈩䈇䉎䈖䈫䉕䈗⏕䈒䈣䈘䈇䇯
䊶ㅢା䊒䊨䊃䉮䊦䈲䇮Compoway/F(Sysway)䇮Modbus䉕䉰䊘䊷䊃䈚䈩䈇䉁䈜䇯䊒䊨䉫䊤䊛䉺䉟䊒䈲
Sysway䉕䉰䊘䊷䊃䈚䈩䈇䉁䈞䉖䇯
䊶⺋േ䈱ේ࿃䈫䈭䉍䉁䈜䈱䈪䇮ᒻE53-CNQ01N2䇮ᒻE53-CN01N2䈍䉋䈶ᒻE53-CNH01N2䈲䇮
䇸
–H
䉺䉟䊒䇹䇸
–HT
䉺䉟䊒䇹䈪䈱䉂䈗↪䈒䈣䈘䈇䇯
䊶᭽䋺DC12V䇭21mA䋨⍴⛊⼔࿁〝ઃ䈐䋩
䂓ᓮജ䋲䋨㔚ജ䋩
䊶᭽䋺DC12V±10%䇭20mA䇭㩿⍴⛊⼔࿁〝ઃ䈐㪀
䋪ᒻES1B↪ᄖㇱଏ⛎㔚Ḯ䉕↪ㅜ䈪↪䈘䉏䉎႐ว䈲ᒰ␠༡ᬺᜂᒰ⠪䉁䈪䈗⋧⺣䈒䈣䈘䈇䇯
㩷㩷㩷ᒻE53-CNPHN2䇮ᒻE53-CNPBN2䈍䉋䈶ᒻE53-CNP03N2䈲䇮ᒻES1B↪䉶䊮䉰ജ䉕ᜬ䈢䈭䈇
䇭㩷䇸
–H
䉺䉟䊒䇹䇸
–HT
䉺䉟䊒䇹䈪䈲↪䈚䈭䈇䈪䈒䈣䈘䈇䇯
䂓ᒻES1B↪ᄖㇱଏ⛎㔚Ḯ
䂓વㅍജ
䊶4-20mA䇮⸵ኈ⽶⩄䍐䍻䍩䍽䍎䍞䍼䍻䍛䋺600Ωએ䇮ಽ⸃⢻䋺⚂10000
䊶
⺋േ䈱ේ࿃䈫䈭䉍䉁䈜䈱䈪䇮E53-CNQFN2䈍䉋䈶E53-CNBFN2䈲䇮䇸–H䉺䉟䊒䇹䇸–HT䉺䉟䊒䇹䈪䈱䉂䈗
㩷㩷↪䈒䈣䈘䈇䇯
• For -500 models, install the E53-CN䂔䂔N2.
• Some settings are not displayed on models with a model number with an "-H" or "-HT" suffix.
• For detailed operating instructions, refer to the E5CN/E5AN/E5EN User's Manual, E5CN-H/E5EN-H/E5AN-H User's Manual, or
E5CN-HT/E5EN-HT/E5AN-HT User's Manual.
• For detailed communications specifications, refer to the E5CN/E5AN/E5EN Communications Manual, E5CN-H/E5EN-H/E5AN-H
Communications Manual, or E5CN-HT/E5EN-HT/E5AN-HT User's Manual.
•
The communications settings (e.g., communications speed) must be the same as those of the host computer.
• The following communications protocols are supported: CompoWay/F (Sysway) and Modbus.
Programmable models do not support the SYSWAY communications protocol.
•
Use the E53-CNQ01N2, E53-CN01N2, or E53-CNH01N2 only for models with a model number with an "-H"
or "-HT" suffix. Otherwise, malfunction may result.
• Specifications: 12 VDC, 21 mA (with short-circuit protection circuit)
䂓Control Output 2 (Voltage Output)
• Specifications:12 VDCr10% at 20mA (with short-circuit protection circuit)
*Consult your OMRON sales representative about using the ES1B Infrared Thermosensor's external power supply for
other purposes. Do not use the E53-CNPHN2, E53-CNPBN2, or E53-CNP03N2 for models with a model number with an
"-H" or "-HT" suffix that do not have an ES1B sensor input.
䂓External Power Supply for ES1B
䂓
Communication (RS-485,RS-232C)
䂓Transfer output
• 4 to 20 mA, Allowable load impedance: 600 Ω max., Resolution: Approx. 10,000
•
Use the E53-CNQFN2 or E53-CNBFN2 only for models with a model number with an "-H" or "-HT" suffix.
Otherwise, malfunction may result.
To Next Page
Need help?
General
