Orbit 96894 Quick Start Guide

Do not connect to power
source until after wiring
valves to timer
TIMER
QUICK START
GUIDE
RESET
PROGRAM
RAIN DELAY
AUTO
OFF
SET
CLOCK
SET
DATE
BUDGET
HOW
OFTE N
RUN
TIM E
START
TIME
PN 96894-50 rA
p 801 295 9820
f 801 951 5815
www.fluid-studio.net
1065 South 500 West
Bountiful, Utah 84010
proof no: 1
date: 05.19.10
des: SM spck: XX
job no: NA
client: Orbit
sku: 96894
upc: NA
file name: 96894-50 rA.indd
software: InDesign CS3
colors
additional instructions:
· Font sizes cannot be smaller than 7 pt.
· Accordian Fold
fold color
non printing
PMS
????
PMS
????
color
non printing
PMS
????
Registration
K
Printers are responsible for
meeting print production
requirements. Any changes
must be approved by the
client and Fluid Studio.
printed piece must meet
designated specifications
on this form.
dimensions:
flat: w: 16" h: 14"
finished: w 16" d: " h 14"
© 2007 Fluid Studio. This
work is the property of Fluid
Studio, and cannot be used,
reproduced or distributed
in any way without their
express permission.
Or
1. SELECT LOCATION
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
AUTO
OFF
SET
CLOCK
SET
DAY
BUDGET
HOW
OFTEN
RUN
TIME
START
TIME
.
For detailed instructions on outdoor wiring, see manual page 8
Warning: Check state and local codes. Orbit recommends using a
licensed electrical contractor for outdoor wiring of timer.
Indoor
Outdoor
Clean, dry, and out of direct sunlight
Allow 23 cm clearance for the swing door
4. CONNECT VALVE WIRE
TO TERMINAL
Station 1
Push tab
upward to
release wire
Strip wire
Push in
Only connect one valve to
each terminal (station)
Keyhole
Pre-formed
mounting holes
No. 8 Screw
Wall
3 mm
2. MOUNT TIMER
Level
Screw through one of the
pre-formed mounting holes.
MOUNTING TEMPLATE
GABARIT D`INSTALLATION
GUIA DE COLGAR
4.17”
(106mm)
p 801 295 9820
f 801 951 5815
www.fl uid-studio.net
1065 South 500 We st
Bountiful, Utah 84010
proof no: 3
date: 10.05.07
des: SM spck: SM
job no: 07WTM005259
client: Orbit
sku: 57880
upc: ? ????? ????? ?
fi le name: 07WTM005259
57880-04 rA.indd
software: Illustrator CS2
colors
additional instructions:
·
·
crop color
non printing
PMS
????
PMS
????
color
non printing
PMS
????
Registration
K
Printers are responsible for
meeting print production
requirements. Any changes
must be approved by the
client and Fluid Studio.
printed piece must meet
designated specifi cations
on this form.
dimensions:
fl a t : w: 9" h: 7"
fi nished: w 9" d: 0" h 7"
© 2007 Fluid Studio. Th is
work is the property of Fluid
Studio, and cannot be used,
reproduced or distributed
in any way without their
express permission.
Use included mounting template to
mark screw locations.
Hang timer on screw using keyhole.
To
Timer
Wire Nut
Solenoid
Common Wire
Valve
Connect one of the two wires from each valve to the
common wire leading to the timer (usually white).
Connect the other wire from each valve to one of the
colored wires leading to the timer.
3. CONNECT SPRINKLER
VALVES TO TIMER WIRES
REQUIRED TOOLS:
Phillips Screwdriver
Wire Strippers

Orbit 96894 Specifications

General

Brand	Orbit
Model	96894
Category	Timer
Language	English