MOVING DOOR CAN CAUSE SERIOUS INJURY OR DEATH.
•DO NOT install transmitter unless the door operator’s safety device works as required by the door
operator’s manual.
• Wall Console must be mounted in sight of door, at least 5 feet above oor and clear of moving door parts.
•Keep people clear of opening while door is moving.
•DO NOT allow children to play with the transmitter or door operator.
If safety reverse does not work properly:
•Close door then disconnect opener using the manual release handle.
•DO NOT use transmitter or door operator.
• Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.
FCC Part 15.21 Statement:
Changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
FCC / IC Statement:
This device complies with FCC Part 15 and Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation of the device.
NOT FOR USE WITH ANY GARAGE DOOR OPENER MANUFACTURED PRIOR TO 1993.
SAFETY BEAMS (PHOTOCELLS) MUST BE IN PLACE AND OPERATIONAL.
THINGS TO KNOW BEFORE STARTING:
• During programming, the garage door opener may operate. Ensure that the garage door opening is clear
of personnel or any obstructions.
• Do not to press the LEARN button for longer than the noted 2-3 seconds as it could cause your existing,
operational remotes and keypads to no longer work.
Below are the brands and specications that this remote is compatible with and the available methods that
can be used to program them. Review Chart A for compatibility and method, then proceed to STEP 1.
NOTE: During programming, the garage door opener will operate. Ensure that the
garage door opening is clear of personnel or any obstructions.
Chart A
PARTS
Visor Clip
Visor Clip
Holder
Key Chain
1. Remove small phillips head backing screw.
2. Pry case open with small coin or screwdriver.
3. Replace battery with CR2032 coin cell.
STEP 1 - Find Specications & Learn Button
1. Locate the brand and opener/receiver specications for your device by consulting the label on the
opener/receiver, the instruction manual, the current remote controls for the opener, or the original
manufacturer of the opener/receiver.
2. Find the LEARN/PROG button on your device - shape, color or name of this button could vary by brand.
For garage door openers, be sure to check under the light covers. For commercial or gate openers,
this button may be on the circuit board of the opener. In some cases, this button could also be on an
external receiver that is mounted on or nearby the product. Consult the devices manual if needed.
STEP 3 - PROGRAMMING REMOTE
Review Chart A to nd your specications and available programming options. Each button can be
programmed individually to operate up to 4 dierent brands of garage door openers and gate receivers.
Activation Tab: Pull tab to activate the remote.
STEP 2 - Activate Remote/Button Layout & Led
LED - The LED will light with each button press and will
also light in response to button presses during dierent
programming modes.
1 2
3 4
FIG. 1
PRGM
SET
RADIO
SIGNAL
LEARN
CODE
CODE
LEARN
Gate
Receivers
EXAMPLES:
*For Marantec® openers, reference operator manual to program remotes to the operator head.
UNIVERSAL REMOTE
INSTRUCTIONS
To Clear the Universal Remote:
ID# 4 ONLY: Chamberlain®/LiftMaster®/Craftsman® Yellow Learn Button Inst.
1. On remote, press and hold down button #2. (Reference FIG. 1)
2. While still holding down button #2, press button #4 four times - then release both buttons (blue LED begins
ashing)
3. Press the remote button of your choice four times and then simply WAIT until the blue LED stops blinking and
goes out (@15 sec).
4. Press and hold down the remote button you just chose - after the white LED blinks (@5 sec) - release button.
4a. ONLY IF you had to manually change your Yellow Learn Button opener to a 390MHz due to
interference issues - simply press and hold the button in the step above for 10 seconds - after the
white LEDs blink for the second time - all LEDs will go out completely - then release the button. If
you did not have to manually change the opener to 390MHz, ignore this line 4a.
5. On the opener, press the LEARN/PROGRAM button for 2-3 seconds - then release.
6. On the remote, press the button you chose ONE time. Opener will click.
7. On the opener, press the LEARN/PROGRAM button again for 2-3 seconds - then release.
8. On the remote, press the button you chose ONE time again. Opener will click again.
9. Test the button - programming is complete.
TIP: Allow the LED light on the universal transmitter to stop ashing before your next button press.
LEARN METHOD
1. Find and remember the required number of button presses (ID#) in the LEARN METHOD column
next to your brands/specication in Chart A.
IMPORTANT: For ID#4 Chamberlain®/LiftMaster®/Craftsman® Yellow Learn Button ONLY - move
immediately to instructions at right. For all other ID#s, proceed below.
2. On remote, press and hold down button #2. (Reference FIG. 1)
3. While still holding down button #2, press button #4 four times - then release
both buttons (blue LED begins ashing).
4. Press the remote button of your choice the required number of times from Chart A and then
simply WAIT until the blue LED stops blinking and goes out (@15 sec).
5. On the opener, press the LEARN/PROGRAM button for 2-3 seconds - then release.
6. Press and release the remote button you just programmed once every 2 seconds until the garage door
opener operates.
7. Test the button - programming is complete.
TIP: Allow the LED light on the universal transmitter to stop ashing before your next button press.
AVAILABLE PROGRAM METHOD
LEARN METHOD ID#
Brand Name Specication Notes
Number of
Button Presses (ID#)
Genie® 315/390 MHz, Intellicode® I, 1995-current 1
Overhead Door® 315/390 MHz, CodeDodger® I, 1995-current 1
Chamberlain®
LiftMaster®
CraftsMan®
Purple Learn Button, Security +®, 2006-2014, 315 MHz 2
Orange/Red Learn Button, Security +®, 1996-2005, 390 MHz 3
Yellow Learn Button, Security +2.0®, 2011-current, 315, 390 MHz
4
Green Learn Button, Billion Code®, 1993-1995, 390 MHz 5
Genie® 315/390 MHz, Intellicode® II, 2010-2011 6
Overhead Door® 315/390 MHz, CodeDodger® II, 2010-2011 6
Sommer® 310 MHz, Rolling Code 7
Linear® 318 MHz, Mega Code® 8
Wayne Dalton® 372.5 MHz, Rolling Code, 1999-current 9
Ryobi® 372.5 MHz, Rolling Code 10
Guardian® 303 MHz, Fixed Learn Code 11
Xtreme® brand 303 MHz, Fixed Learn Code 11
Marantec® 315 MHz, Fixed Learn Code 12
*Chamberlain® 390 MHz, 9 Switch/3 Position Dip Switch
*Stanley® 310 MHz, 10 Switch/2 position Dip Switch
*Genie® 390 MHz, 9 & 12 Switch/2 Position Dip Switch, 1993-1995
*Overhead Door®
360,380,390,412 MHz, 9 Switch/3 Position Dip Switch,
1993-Current
Changing The Battery
Overhead Door® and CodeDodger® are registered trademarks of Overhead Door Corporation. All other listed names and
trademarks are the property of their respective owners.
*For instructions on these Overhead Door® specications, visit www.overheaddoor.com/documents/universal-
remote-dip-switches.pdf
For these dip switch instructions,
visit
www.overheaddoor.com*
For Patent Information: www.overheaddoor.com/patents
©2022, Overhead Door Corporation
If at any time you need to clear the universal remote of its programming and start again, follow the below steps.
If you have only one opener, you may also simply program over what has previously been done.
1. On the remote, press and hold down button #3. (Reference FIG. 1)
2. While still holding down button #3, press button #4 four times - then release both buttons
(LED will ash and go out).
If the above does not work, clear the remote in the same manner that you would clear an original OEM remote
from the head. Please consult your opener manual for instruction. In most situations, clearing at the opener
head will clear all radio frequency devices (like remotes or keypads) that are currently programmed.
Programming Assistance:
If the opener does not activate after the steps shown, repeat steps or contact Customer Care by
phone at: 1-800-929-3667 for programming assistance. You may also scan this QR code for additional
information and links.
To Next Page
Need help?
General
