110
The System Setup and Other Setup menus
12
8 Select the HPF (High Pass Filter) setting you want.
This can only be set when ZONE 2 is selected in step 2.
The low frequency component output from the AUDIO ZONE 2 OUT terminals is cut. When a subwoofer is con-
nected in Zone 2, we recommend setting this to “ON”. This is only valid when Zone 2 is connected using the
AUDIO ZONE 2 OUT terminals.
! OFF (default) – The High Pass Filter function is disabled.
! ON – The High Pass Filter function is enabled.
9 Select the TONE setting you want.
This can only be set when ZONE 2 is selected in step 2.
The bass and treble for ZONE 2 can be adjusted. When BYPASS is selected, the original sound is played as such.
When ON is selected, the BASS and TREBLE can be adjusted.
! When the speaker terminals are being used for ZONE 2, the ZONE 2 TONE effect is available when
Speaker System is set to 5.2 +ZONE 2+ZONE 3 or 5.2 +ZONE 2+HDZONE. The ZONE 2 TONE effect is not
available when Multi-ZONE Music is selected.
10 Adjust the bass (BASS) and treble (TREBLE) to your tastes.
This can only be set when ZONE 2 is selected in step 2 and ON is selected in step 8.
The BASS and TREBLE can each be adjusted between –10.0dB and +10.0dB, in 1 dB steps.
11 When you’re finished, press RETURN.
You will return to the Other Setup menu.
On Screen Display Setup
When the receiver is operated, its status (the input name, listening mode, etc.) is displayed superimposed over
the video output on the display. This status display can be turned off by switching this setting to OFF. The setting
can be made for the main zone and HDZONE, respectively.
! Default: ON (both the main zone and HDZONE)
1 Select ‘On Screen Display Setup’ from the Other Setup menu.
2 Select and set the main zone or HDZONE for which you wish to change the setting.
3 Select the On Screen Display setting you want.
4 When you’re finished, press RETURN.
You will return to the Other Setup menu.
Notes
! The on-screen display is only displayed for video output from the HDMI terminal.
! When the video input signal is a 3D signal, the on-screen display may not be displayed.
! The size of the characters displayed differs according to the output resolution.
Play ZONE Setup
Select the zone for playing the audio contents of devices in the home network when using in the DMR mode.
! For playable DLNA-compatible network devices, see page 69 .
1 Select ‘Play ZONE Setup’ from the Other Setup menu.
2 Select the zone in which you want to play the audio contents.
3 When you’re finished, press RETURN.
You will return to the Other Setup menu.
Notes
! If another zone is on, it may not be possible to play the audio contents. In this case, turn the other zone off,
then play the audio contents.
! MAIN/HDZONE at ZONE Setup must be set to HDZONE in order to use the HDZONE function (page 109 ).
Multi Channel Input Setup
SC-LX88 only
You can adjust the level of the subwoofer for a multi-channel input. Also, when the multi-channel input is
selected as an input function, you can display the video images of other input functions. In the Multi Channel
Input Setup, you can assign a video input to the multi-channel input.
1 Select ‘Multi Ch In Setup’ from the Other Setup menu.
2 Select the ‘SW Input Gain’ setting you want.
! 0dB – Outputs sound of the subwoofer at the level originally recorded on the source.
! +10dB – Outputs sound of the subwoofer at the level increased by 10 dB.
3 Select the ‘Video Input’ setting you want.
When the multi-channel input is selected as an input function, you can display the video images of other input
functions. The video input can be selected from the following: SAT/CBL, DVR/BDR, OFF.
4 When you’re finished, press RETURN.
You will return to the Other Setup menu.
Maintenance Mode
Only use this if so instructed by a Pioneer service engineer or custom installer.
To Next Page
Loading...
Need help?
General
Weight and Dimensions
