Sharp 14D2-G User Manual

10
10-1 10-2
14D1-S/G/W
14D2-S/G
FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)
No. Adjusting point Adjusting procedure/conditions Waveform and others
CONTRAST key
1. Receive "Monoscope Pattern" signal. 2. Set P-Mode to select CONTRAST. 3. Press Volume Up/Down key to check whether the
CONTRAST effect is OK or not.
1
1. Receive "Color Bar" signal. 2. Set P-Mode to select COLOUR. 3. Press Volume Up/Down key to check whether
the COLOUR effect is OK or not.
2
COLOUR key
BRIGHTNESS key
1. Receive "Monoscope Pattern" signal. 2. Set P-Mode to select BRIGHTNESS. 3. Press Volume Up/Down key to check whether
the BRIGHTNESS effect is OK or not.
3
TINT key 1. Receive the "NTSC Colour Bar" signal thru AV in.
2. Set P-Mode to select TINT. 3. Press Volume Up/Down key to check TINT, UP
for GREEN direction and DOWN for PURPLE di- rection whether is OK or not.
4
SHARPNESS Key
1. Receive "Monoscope Pattern" signal. 2. Set P-mode to select SHARPNESS. 3. Press Volume Up/Down key to check whether
the SHARPNESS effect is OK or not.
5
WHITE TEMP 1. Receive "Monoscope Pattern" signal.
2. Set FUNCTION to select WHITE TEMP. 3. Press Volume Up/Down key to check WHITE
TEMP Option, STANDARD: NORMAL SETTING, WARM for more REDDISH direction changing, COOL for more BLUISH di- rection changing.
8
NORMAL Key7
1. Once in PICTURE Mode, and theNORMAL key
is pressed, all the settings will be present to nor- mal setting. (Normal setting value for every mode). » CONTRAST : MAX » COLOUR : CENTER » BRIGHTNESS : CENTER » TINT : CENTER » SHARPNESS : CENTER
Notes:If nothing is display
mean contrast, colour, bright, tint, sharpness are all in nor- mal setting.
CH DISPLAY COLOUR
1. All Ch (1~99) will have an OSD display of the
channel number in green colour under AFT ON condition.
6
FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)
(Continued)
No. Adjusting point Adjusting procedure/conditions Waveform and others
COLOUR SYSTEM
1. Receive the "PAL COLOUR BAR" signal, press
the COLOUR SYSTEM key to select modes ex- cept PAL, check the COLOUR is not working prop- erly. Then, select the "PAL" mode. Check again its colour so that it is working properly.
2. Receive "SECAM COLOUR BAR" signal, press
COLOUR SYSTEM key to select modes except SECAM, check the COLOUR is not working prop- erly. Then, select the "SECAM" mode. Check again its colour so that it is working properly.
3. Receive "NTSC 4.43/3.58 COLOUR BAR" signal
thru AV, press COLOUR SYSTEM key to select modes except N4.43/3.58, check the COLOUR is not working properly. Then, select the "NTSC 4.43/3.58" mode. Check again its colour so that it is working properly.
9
OSD LAN- GUAGE QUANTITY CHECK
Check OSD LANGUAGE quantity and type as Eng- lish, Russian, Chinese, French, Arabic and Malay.
12
1. Receive "PAL COLOUR BAR" signal. 2. Turn up the volume control to maximum, make
sure the sound is heard from the speakers. Then put the unit in no signal state.
3. Check the sound mute is effective. 4. Finally turn sound level of CTV to minimum.
SOUND SYSTEM
10 1. Receive "PAL-D/K" signal, press the "SOUND
SYSTEM" to select B/G, I. Check the sound out- put is not working properly. Select D/K and check the sound output to make sure it is working prop- erly.
2. Receive "PAL-I" signal, press the "SOUND SYS-
TEM" to select B/G, D/K. Check the sound output is not working properly. Select I and check the sound output to make sure it is working properly.
3. Receive "PAL-B/G" signal, press the "SOUND
SYSTEM"to select I, D/K. Check the sound out- put is not working properly. Select B/G and check the sound output to make sure it is working prop- erly.
NOISE MUTE CHECKING
11

Sharp 14D2-G Specifications

General

Brand	Sharp
Model	14D2-G
Category	TV
Language	English