BUS CONTROL IN
BUS AUDIO IN
Source selector*
Sélecteur de source*
XA-C30
* not supplied
non f ourni
Sony Corporation © 2003 Printed in Korea
3-251-806-11 (1)
Cautions
• This unit is designed for negative ground 12 V DC
operation only.
• Do not get the wires under a screw, or caught in
moving parts (e.g. seat railing).
• Before making connections, turn the car ignition
off to avoid short circuits.
• Connect the yellow and red power input leads
only after all other leads have been connected.
• Run all ground wires to a common ground
point.
• Be sure to insulate any loose unconnected wires
with electrical tape for safety.
• The use of optical instruments with this product
will increase eye hazard.
Notes on the power supply cord (yellow )
• When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
• When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
• The numbers in the list are keyed to those in the
instructions.
• The bracket 1 and the protection collar 3 are
attached to the unit before shipping. Before
mounting the unit, use the release keys 5 to
remove the bracket 1 and the protection collar 3
from the unit. For details, see “Removing the
protection collar and the bracket (4)” on the
reverse side of the sheet.
• Keep the release keys 5 for future use as they
are also necessary if you remove the unit from
your car.
Caut ion
Handle the bracket 1 carefully to avoid injuring
your fingers.
Note
Bef ore installing, make sure that t he catches on both
sides of t he bracket 1 are bent inwards 2 mm (
3
/32 in). If
the cat ches are st raight or bent out wards, the unit
will not be inst alled securely and may spring out.
Installation/Connections
Installation/Connexions
FM/AM
Compact Disc
Player
Connection example (2)
Notes (2-A)
• Be sure t o connect the ground cord before connect ing
the amplif ier.
• If you connect an optional power amplifier and do not
use the built -in amplif ier, t he beep sound w ill be
deactivat ed.
Tip (2-B-
)
For connect ing t wo or more CD/MD changers, the source
select or XA-C30 (optional) is necessary.
Connection diagram (3)
1 To a metal surface of the car
First connect the black ground lead, t hen connect
the yellow and red pow er input leads.
2 To the power antenna control lead or pow er
supply lead of antenna booster amplifier
Notes
• It is not necessary t o connect this lead if there is no
pow er ant enna or antenna boost er, or wit h a
manually-operated t elescopic ant enna.
• When your car has a built -in FM/AM ant enna in
the rear/side glass, see “ Notes on t he cont rol and
pow er supply leads.”
3 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any ot her syst em may damage t he unit.
4 To the interface cable of a car telephone
5 To the +12 V pow er terminal which is energized
in the accessory position of the ignition key
sw itch
Notes
• If there is no accessory position, connect to the +12
V pow er (bat tery) t erminal which is energized at
all t imes.
Be sure to connect t he black ground lead to a
metal surface of the car first .
• When your car has a built -in FM/AM ant enna in
the rear/side glass, see “ Notes on t he cont rol and
pow er supply leads.”
6 To the +12 V pow er terminal which is energized
at all times
Be sure to connect t he black ground lead to a metal
surface of the car first .
Notes on the control and pow er supply leads
• The power antenna control lead (blue) supplies +12 V
DC w hen you turn on the t uner.
• When your car has built -in FM/AM ant enna in the rear/
side glass, connect t he power antenna control lead
(blue) or the accessory power input lead (red) to the
pow er terminal of t he existing ant enna booster. For
details, consult your dealer.
• A power antenna wit hout relay box cannot be used
wit h t his unit .
2
A
B
AUDIO OUT REAR
BUS AUDIO IN
BUS CONTROL IN
1
45
Equipment used in illust rat ions (not supplied)
Appareils utilisés dans les illustrations (non fournis)
Rear speaker
Haut-parleur arrière
Front speaker
Haut-parleur avant
1
CD/MD changer
Changeur de CD/ M D
Rotary commander RM-X4S
Satellite de commande RM -X4S
Power amplifier
Amplificateur de puissance
× 4
23
CDX-MP40
× 2
1
Catch
AUDIO OUT FRONT
Downloaded from: https://www.usersmanualguide.com/
To Next Page
Need help?
General
