SERVICE MANUAL
Sony Video & Sound Products Inc.
HT-ST5000
SA-ST5000
SPECIFICATIONS
HT-ST5000
SOUND BAR
SA-ST5000
ACTIVE SPEAKER SYSTEM
9-896-393-01
2017D33-1
©
2017.04
US Model
Canadian Model
AEP Model
UK Model
Ver. 1.0 2017.04
• All of the units included in the HT-ST5000
(SA-ST5000/SA-WST5000/Remote control)
are required to confi rming operation of SA-
ST5000. Check in advance that you have all
of the units.
COMPONENT MODEL NAME
HT-ST5000
Bar Speaker (Active Speaker System) SA-ST5000
Subwoofer (Active Subwoofer) SA-WST5000
• Please refer to service manual separately issued for Subwoofer.
Note:
Be sure to keep your PC used for service and
checking of this unit always updated with the
latest version of your anti-virus software.
In case a virus affected unit was found during
service, contact your Service Headquarters.
Amplier section
U.S. models:
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(FTC)
Front L + Front R:
With 6ohms loads, both channels
driven, from 200 - 6,000Hz; rated
20W per channel minimum RMS
power, with no more than 1% total
harmonic distortion from 250mW to
rated output.
Front tweeter L + Front tweeter R:
With 6ohms loads, both channels
driven, from 6,000 - 20,000Hz; rated
20W per channel minimum RMS
power, with no more than 1% total
harmonic distortion from 250mW to
rated output.
POWER OUTPUT (reference)
Front L/Front R speaker blocks: 50W
(per channel at 6ohms, 1kHz)
Front tweeter L/Front tweeter R
speaker blocks: 50 W (per channel at
6ohms, 10kHz)
Center speaker block: 50 W (per
channel at 6ohms, 1kHz)
Center tweeter speaker block: 50 W
(per channel at 6ohms, 10kHz)
Top speaker block: 50 W (per channel
at 6ohms, 1kHz)
CND, AEP, UK models:
POWER OUTPUT (rated)
Front L + Front R: 30W + 30W
(at 6ohms, 1kHz, 1% THD)
POWER OUTPUT (reference)
Front L/Front R speaker blocks: 50W
(per channel at 6ohms, 1kHz)
Front tweeter L/Front tweeter R
speaker blocks: 50 W (per channel at
6ohms, 10kHz)
Center speaker block: 50 W (per
channel at 6ohms, 1kHz)
Center tweeter speaker block: 50 W
(per channel at 6ohms, 10kHz)
Top speaker block: 50 W (per channel
at 6ohms, 1kHz)
HDMI Section
Connector
Type A (19pin)
USB section
(USB) port:
Type A (For connecting USB memory)
LAN section
LAN(100) terminal
100BASE-TX Terminal
Wireless LAN section
Communication system
IEEE 802.11 a/b/g/n
Frequency band
2.4GHz, 5GHz
BLUETOOTH section
Communication system
BLUETOOTH Specication version 4.1
Output
BLUETOOTH Specication Power
Class1
Maximum communication range
Line of sight approx. 30m
1)
Maximum number of devices to be
registered
9 devices
Frequency band
2.4 GHz band (2.4GHz - 2.4835GHz)
Modulation method
FHSS (Freq Hopping Spread Spectrum)
Compatible BLUETOOTH proles
2)
A2DP 1.2 (Advanced Audio Distribution
Prole)
AVRCP 1.5 (Audio Video Remote
Control Prole)
Supported Codecs
3)
SBC
4)
, AAC
5)
, LDAC
Transmission range (A2DP)
20 Hz - 40,000 Hz (LDAC sampling
frequency 96kHz with 990 kbps
transmission)
20 Hz - 20,000 Hz (Sampling frequency
44.1kHz)
1)
The actual range will vary depending on
factors such as obstacles between
devices, magnetic elds around a
microwave oven, static electricity,
cordless phone use, reception
sensitivity, the operating system,
software applications, etc.
2)
BLUETOOTH standard proles indicate
the purpose of BLUETOOTH
communication between devices.
3)
Codec: Audio signal compression and
conversion format
4)
Abbreviation for Subband Codec
5)
Abbreviation for Advanced Audio
Coding
Front L/Front R speaker block section
Speaker system
2-way coaxial speaker system,
Acoustic suspension
Speaker
Woofer: 65mm (2 5/8 in.) cone type,
Magnetic uid speaker
Tweeter: 14mm (9/16 in.) soft dome
type
Center speaker block section
Speaker system
Center: 2-way coaxial speaker system,
Acoustic suspension
Satellite: Full range speaker system,
Acoustic suspension
Speaker (5 speakers)
Center woofer: 65mm (2 5/8 in.) cone
type, Magnetic uid speaker
Tweeter: 14mm (9/16 in.) soft dome
type
Satellite: 65mm (2 5/8 in.) cone type,
Magnetic uid speaker
Top speaker block section
Speaker system
Full range speaker system, Acoustic
suspension
Speaker
65mm (2 5/8 in.) cone type, Magnetic
uid speaker
General
Power requirements
120 V AC, 60 Hz (US, CND)
Power consumption
On: 90W
For details about the power
consumption during standby mode,
see “Power Consumption by the
Setting Value for Each Standby
Mode”
Dimensions* (approx.) (w/h/d)
1,180mm × 80mm × 142mm (46 1/2 in
× 3 1/4 in × 5 5/8 in) (without grille
frame)
1,180mm × 80mm × 145mm (46 1/2 in
× 3 1/4 in × 5 3/4 in) (with grille frame)
*Not including projection portion
Mass (approx.)
8.3kg (18 lb 4 4/5 oz) (without grille
frame)
8.8kg (19 lb 6 2/5 oz) (with grille
frame)
Compatible iPod/iPhone models
The compatible iPod/iPhone models are as
follows. Update your iPod/iPhone with the
latest software before using with the
system.
BLUETOOTH technology works with:
iPhone 7 Plus/iPhone 7/iPhone SE/iPhone
6s Plus/iPhone 6s/iPhone 6 Plus/
iPhone6/iPhone 5s/iPhone 5c/iPhone 5/
iPhone 4s
iPod touch (6th generation)/iPod touch
(5th generation)
Inputs
HDMI IN 1/2/3*
ANALOG IN
TV IN (OPT)
Outputs
HDMI OUT (TV (ARC))*
*HDMI IN 1/2/3 and HDMI OUT (TV (ARC))
jacks support HDCP 2.2 protocol. HDCP
2.2 is newly enhanced copyright
protection technology that is used to
protect content such as 4K movies.
Design and specications are subject to
change without notice.
Communication system
Wireless Sound Specication version
3.0
Frequency band
5.2GHz (5.180GHz - 5.240GHz)
5.8GHz (5.736GHz - 5.814GHz)
Modulation method
DSSS
Wireless transmitter section
• Bar Speaker (1)
• Grille frame (1)
• Remote control (1)
• R03 (size AAA) battery (2)
• WALL MOUNT TEMPLATE (1)
• Optical digital cable (1) (AEP, UK)
What’s in the Box
• Startup Guide
• Operating Instructions
• HDMI cable (supports the specication
equal to Premium High Speed HDMI
cable with Ethernet) (1) (US, CND)
• Subwoofer (1)
220 V - 240 V AC, 50 Hz/60 Hz (AEP, UK)
To Next Page
Need help?
General
Weight and Dimensions
